INSTRUCTION BOOKLET GB GAS HOB TBG 640 Please read this instruction booklet before using the appliance 1 IE
Important Safety Information You MUST read these warnings carefully before installing or using the oven. If you need assistance, contact our Customer Care Department on 08705 950950 Installation ! ! ! ! ! ! ! This appliance must be installed and serviced by a competent person as stated in the Gas Safety (Installation and Use) Regulations Current Editionsand the IEE Wiring Regulations. For appliances installed in the Republic of Ireland please refer to NSAI-Domestic Gas Installations I.S.
Contents For the User For the Installer Important Safety Information Description of the Hob Operation Maintenance and Cleaning Something Not Working? Service and Spare Parts Customer Care Department 2 3 4 5 6 6 7 Guarantee Conditions 7 Engineers technical data Important safety requirements Installation Building In Electrical connections Wiring diagram Fault finding Commissioning Conversion from natural gas to LPG 8 9 10 11 12 13 13 15 15 Guide to Use the instructions The following symbols will be fo
Operation Hob Burners " To light a burner: ! push the electric ignition pushbutton which is marked ! by a little spark ( ); at the same time turn the relevant control knob anticlockwise to maximum position ( ); upon ignition, keep the knob pushed down about 5 seconds. This will allow the "thermocouple" (see diagram, lett. D) to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted. ! then, check the flame is regular and adjust it as required.
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Wipe the hob top regularly using a well wrung out soft cloth and a little washing up liquid.
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee.
Customer Care Department For general enquiries concerning your Tricity Bendix appliance or for further information on Tricity Bendix products, please contact our Customer Care Department by letter or telephone at the address below or visit our website at www.tricity-bendix.co.
Instructions for the Installer Engineers technical data Overall dimensions Width Depth Height (Above worktop) Rear Left Burner (semi-rapid) Heat Input 2.0 kW (6824 BTU/HR) 580 mm. 500 mm. 8 mm. Front Left Burner (rapid) Heat Input 3.0 kW Natural Gas (10236 BTU/HR) 2.8 kW L.P.G. (9554 BTU/HR) Cut out dimensions Width Depth Thickness 550 mm. 470 mm. 30 mm. Rear Right Burner (semi-rapid) Heat Input 2.0 kW (6824 BTU/HR) Front Right Burner (auxiliary) Heat Input 1.
Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S. 813 Current Editions and the ETCI Rules for Electrical Installations.
Installation IMPORTANT This hob must be installed by qualified personnel to the relevant British Standards. Any gas installation must be carried out by a registered CORGI installer. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. WHEN THE HOB IS FIRST INSTALLED Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory.
Building In 1 ON/OFF SWITCH Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2.
Electrical Connections THIS HOB MUST BE EARTHED. Permanent Connection Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations.
Wiring diagram L 1 A 0 2 3 220/240 A. IGNITOR SWITCH 4 B. IGNITOR UNIT B N Fault finding Preliminary Electrical Systems Check Green Yellow Earth Wire Green/Yellow START Isolate appliance and carry out: A: Earth Continuity check. ( ) E( ) FUSE Brown Blue SOCKET (face view) PLUG (with cover removed) Neutral Wire Blue N L Blue Brown Green Yellow NO YES Carry out: C: Polarity check. Has inlet fuse blown? NO YES Carry out: D: Resistance to Earth check.
Ignition System / Gas Ignition Ignitor does not spark YES Check gas supply at burner NO Check plug top fuse and replace if necessary Light burner manually Check polarity and earth continuity of supply point Check by pass simmer adjusted Check position of the electrode Check earth continuity of appliance Check continuity from 'N' on the mains connector block and "O" on the ignitor unit Check continuity from 'L' on the mains connector block and the taps ignition switches Check continuity from igni
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. Procedure: " Re-ignite the burner and set to MIN. Remove the control knob.
CUSTOMER CARE Tricity Bendix Major Appliances Addington Way Luton Bedfordshire LU4 9QQ Tel: 08705 950 950 © Electrolux plc 2003 www.electrolux.com 35692-2801 02/06 Grafiche MDM - Forlì www.tricity-bendix.co.
