INSTRUCTION BOOKLET GB GAS HOB TBG 640 Please read this instruction booklet before using the appliance 1
Important Safety Information You MUST read these warnings carefully before installing or using the oven. If you need assistance, contact our Customer Care Department on 08705 950950 Installation z z z z z z z This appliance must be installed and serviced by a competent person as stated in the Gas Safety (Installation and Use) Regulations Current Editionsand the IEE Wiring Regulations. For appliances installed in the Republic of Ireland please refer to NSAI-Domestic Gas Installations I.S.
Contents For the User For the Installer Important Safety Information Description of the Hob Operation Maintenance and Cleaning Something Not Working? Service and Spare Parts Guarantee/Customer Service 2 3 4 5 6 15 16 European Guarantee 17 Engineers technical data Important safety requirements Installation Building In Electrical connections Wiring diagram Fault finding Commissioning Conversion from natural gas to LPG 7 8 9 10 11 12 12 14 14 Guide to Use the instructions The following symbols will be
Operation Hob Burners ) To light a burner: z push the electric ignition pushbutton which is marked z by a little spark ( ); at the same time turn the relevant control knob anticlockwise to maximum position ( ); check the flame is regular and adjust it as required. If you cannot light the flame even after several attempts,check the "cap" and “crown” (see diagram, lett. A, B) are in the correct position. z Do not keep the control knob pressed for more than 15 seconds.
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Wipe the hob top regularly using a well wrung out soft cloth and a little washing up liquid.
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee.
Instructions for the Installer Engineers technical data Overall dimensions Width Depth Height (Above worktop) Rear Left Burner (semi-rapid) Heat Input 2.0 kW (6824 BTU/HR) 580 mm. 500 mm. 8 mm. Front Left Burner (rapid) Heat Input 3.0 kW Natural Gas (10236 BTU/HR) 2.8 kW L.P.G. (9554 BTU/HR) Cut out dimensions Width Depth Thickness 550 mm. 470 mm. 30 mm. Rear Right Burner (semi-rapid) Heat Input 2.0 kW (6824 BTU/HR) Front Right Burner (auxiliary) Heat Input 1.
Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S. 813 Current Editions and the ETCI Rules for Electrical Installations. Provision for ventilation Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. 6172/ B.S.
Installation IMPORTANT This hob must be installed by qualified personnel to the relevant British Standards. Any gas installation must be carried out by a registered CORGI installer. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. WHEN THE HOB IS FIRST INSTALLED Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory.
Building In 1 ON/OFF SWITCH Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2.
Electrical Connections THIS HOB MUST BE EARTHED. Permanent Connection Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations.
Wiring diagram L 1 A 0 2 3 220/240 A. IGNITOR SWITCH 4 B B. IGNITOR UNIT N Fault finding Preliminary Electrical Systems Check Earth Wire Green/Yellow Green Yellow START Isolate appliance and carry out: A: Earth Continuity check. ( ) E( ) FUSE Brown Blue SOCKET (face view) PLUG (with cover removed) Neutral Wire Blue N L Blue Brown Green Yellow NO YES Carry out: C: Polarity check. Has inlet fuse blown? NO YES Carry out: D: Resistance to Earth check.
Ignition System / Gas Ignition Ignitor does not spark YES Check gas supply at burner NO Check plug top fuse and replace if necessary Light burner manually Check polarity and earth continuity of supply point Check by pass simmer adjusted Check position of the electrode Check earth continuity of appliance Check continuity from 'N' on the mains connector block and "O" on the ignitor unit Check continuity from 'L' on the mains connector block and the taps ignition switches Check continuity from igni
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. Procedure: ) Re-ignite the burner and set to MIN. Remove the control knob.
Service and Spare Parts In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Electrolux Service Force Centre by telephoning: 0870 5 929929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www.serviceforce.co.
Guarantee/Customer Service Standard guarantee conditions We, Electrolux, undertake that if within 12 months of the date of the purchase this Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: · The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
European Guarantee This appliance is guaranteed by Electrolux in each of the countries listed below for the period specified in the appliance guarantee or otherwise by law.
www.electrolux.com www.tricity-bendix.co.
