Installation Guide

Please read the manual before use, children shall
operate this product under the guidance of adults,
do not allow children to play with this product.
Do not disassemble, modify or repair the waste
processor
When using, please open the tap first, and then the
disposer; after food waste is grinded, rinse it with
water continuously, so that food waste and
corrosive detergents will not remain in the disposer.
The continuous load operation shall not exceed 10
minutes, and the interval between each use shall be
greater than 30 minutes.
This product is designed to dispose of normal
household food waste;inserting materials other
than food waste into disposer could cause personal
injury and/or property damage.
To reduce the risk of injury and/or property damage,
do not use the sink containing the disposer for
purposes other than food preparation (such as baby
bathing or washing hair).
Turn off the machine and tap only after the food
waste has been grinded and the machine and
running water have been heard.
When not operating a disposer, leave the stopper in
place to reduce the risk of objects falling into the
disposer.
If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly
qualified-persons in order to avoid a hazard.
Do not store or use gasoline or other flammable
vapors and liquids in vicinity of disposer.
Please do not put your hands in the disposer.
LEAK HAZARD: Regularly inspect disposer and
plumbing fittings for leaks, which can cause proper
ty damage and could result in personal injury.
It can handle:Leftovers, vegetables, egg shells,
livestock small bones,tea leaves Fruit skins,small
fruit pits,cooked meat, small corncobs,cereal and
other food waste.
Do not put the following into a disposer: High-
fiber foods,hair, hemp rope, big pork bones,clam or
oyster shells, caustic drain cleaners or similar
products, glass, china, or plastic, metal (such as
bottle caps, steel shot, tin cans, or utensils), hot
grease or other hot liquids.
Note: to prevent water accumulation in the disposer, the water pipe inserted into the wall/
floor drain must be lower than the disposer outlet.
1.Tape measure
2.Wire cutters
3.flashlight
4.wire strippers
5.flathead screwdriver
6.Phillips screwdriver
7.Adjustable pliers
PERSONAL INJURY
Wearing safety glasses is recommended
during the installation of the food waste disposer.
1. Loosen nut (1) at top of trap (4) with pipe wrench .
2. Loosen nut (2) at top of extension pipe. Remove extension pipe..
3. Loosen nut (3) at base of sink flange4.
4. Push sink flange up through sink hole and remove it
5. Clean sink flange area of any putty or other debris.
Remove flange mounting assembly from machine,turn mounting
assembly over,Use Hex wrench to loosen three mounting screws ,
Mounting assembly will now come apart.
Note: the diameter of the disposer flange (GB) is 4.331in.
① Ensure there is no debris around the sink drain hole, mount the upper
seal ring on the flange, and put the flange into the sink drain hole. You
may need to place a heavy object in the sink or hold it down by hand to
keep the flange in place (place a towel under the object to prevent
scratching).
② Under the sink, mount the lower seal ring and upper buckle (flat side
up) on the flange in order.
③ Put the upper buckle of the lower seal ring in place, and mount the
middle buckle on the flange to hold the upper buckle.
④ When the upper and middle buckle of lower seal ting hold the sink
bottom tightly, tighten the three hex socket screws at the same time
until the mounting component is firmly installed on the sink, improper
operation will cause water leakage
Note: the flange is designed with convex points. When the flange is
connected with the middle buckle, the convex points shall be stuck in the
middle of the middle buckle to prevent the equipment from falling due to
vibration.
WARNING:WHEN USING ELECTRIC
APPLIANCES, BASIC PRECAUTIONS ARE
ALWAYS TO BE FOLLOWED, INCLUDING
2.HELPFUL TOOLS
1.INSTALLATION INSTRUCTIONS
3.DISCONNECT SINK DRAIN
1.Sink Plug
2.Stainless Steel Flange
3.Flange Waterproof Rubber
4.Foam Gasket
5.Sink Flange
7.Screws (3)
8.Splash Guard
9.Mounting Ring
10.Dishwasher Inlet
12.Reset Button
6.Backup Ring
11.Dishwasher Valve
(With Rubber Gasket)
13.Water Outlet Gasket
14.Drain Pipe
15.Hex Wrench
16.Dishwasher Connecting
17.Drain Pipe Connecting
(With Rubber Gasket)
1.Dimensions
Model
EM200
CGMD-65
QSD-38
MCD17-T7
12.913in.
13.385in.
12.795in.
13.779in.
3.47in.
3.47in.
3.47in.
3.47in.
3.248in.
3.248in.
3.248in.
3.248in.
4.921in.
5.551in.
4.921in.
5.905in.
7.677in.
7.677in.
7.677in.
7.677in..
Size
① ② ③ ④ ⑤
CAUTION
4.SEPARATE COMPONENTS BEFORE CONNECTION OF
DISPOSER AND SINK
5.CONNECT FLANGE MOUNTING ASSEMBLY TO SINK
For safety and ease of garbage disposal installation, we recommends
the use of these helpful tools
-1- -2-
MOUNTING ASSEMBLY
1 2 3
4
5 6 7
NOTE: This has been designed to operate on 110-120 Volt, 50/60 Hz exclusively. Using any other
voltage or Hz will adversely affect performance.
IMPORTANT: Read all instructions thoroughly. Keep this guide for future reference.
WARNING: Be sure to review safety instructions pertaining to a risk of fire, electrical shock
or injury to persons before using disposal.
PLEASE READ THIS MANUAL CAREFULLY BEFORE USE
THE COMPANY RESERVES THE RIGHT TO INTERPRET THE MANUAL
THE ACTUAL PRODUCT APPEARANCE SHALL PREVAIL.
PLEASE KEEP IT TOGETHER WITH THE INVOICE AFTER READING.
THE PRODUCT TECHNOLOGY OR SOFTWARE MAY BE UNGRADED WITHOUT PRIOR NOTICE
MODEL NO.:EM200
CGMD-65
QSD-38
MCD17-T7
USER MANUAL
FOOD WASTE DISPOSER