User's Manual

7
Configuration D [SW 4 off / SW 5 on / SW 6 on]:
• Button (1/2): Unlocks all entry doors
• Button (3/4): Unlocks all entry and compartment doors
• Button (5/6): Unlocks all curb side compartment doors (relay
banks C-D)
• Button (7/8): Unlocks all driver side compartment doors (relay
banks A-B)
• Button (9/0): Toggles Aux 1 output
• Interior Switch Dip Switch Setting Configurations:
The following vehicle switch assignments of connector J1 and 3 define
functional assignment of interior switches. When the switch input is
grounded, its corresponding function is specified.
Configuration A [SW 4 off / SW 5 off / SW 6 off]:
1) J3 pin 4: Locks all doors
2) J3 pin 3: Unlocks all doors
3) J1 pin 1: Unassigned
4) J1 pin 2: Unassigned
5) J3 pin 5: Unassigned
6) J3 pin 2: Unassigned
Configuration B [SW 4 off / SW 5 off / SW 6 on]:
1) J3 pin 4: Locks all doors
2) J3 pin 3: Unlocks all doors
3) J1 pin 1: Locks all compartment doors (banks A-D, not entry door
relays)
4) J1 pin 2: Unlocks all compartment doors (banks A-D, not entry
door relays)
5) J3 pin 5: Locks entry door(s)
6) J3 pin 2: Unlocks entry door(s)
Configuration C [SW 4 off / SW 5 on / SW 6 off]:
1) J3 pin 4: Locks all doors
2) J3 pin 3: Unlocks entry door(s)
3) J1 pin 1: Unlocks bank A compartment(s)
4) J1 pin 2: Unlocks bank B compartment(s)
5) J3 pin 5: Unlocks bank C compartment(s)
6) J3 pin 2: Unlocks bank D compartment(s)
Configuration D [SW 4 off / SW 5 on / SW 6 on]:
1) J3 pin 4: Locks all doors
2) J3 pin 3: Unlocks all doors
8
3) J1 pin 1: Unlocks curb-side compartment doors (banks C-D)
4) J1 pin 2: Unlocks driver-side compartment doors (banks A-B)
5) J3 pin 5: Locks entry door(s)
6) J3 pin 2: Unlocks entry door(s)
Notes:
• See the table on page 8 for S2 DIP switch assignments.
• Configuration D is the default.
• DIP switch 7:
The setting of DIP switch 7 defines the type of remote fob transmitter,
either standard fob or cargo fob.
• Off: Standard fob
• On: Cargo fob
• DIP switch 8:
The setting of DIP switch 8 defines the type of CAN protocol, either RV-C
or SAE J1939.
• Off: RV-C
• On: SAE J1939
Additional Features
Dome/Porch Light Activation
The dome/porch light is activated for a timed duration (5-60 seconds)
whenever a keypad button is pressed or when system is unlocked from
FOB transmitter or vehicle switch. The time duration is dependent on the
trim pot setting. The dome/porch light is deactivated with starting the
engine or locking the entry doors.
e-PAD Anti-tamper Deactivating Feature
After repeated attempts to enter incorrect codes (20 button presses
without enabling), the keypad enters an inactive mode that disables
button for 1 minute. This helps prevent undesired access by entering
random codes. No beep will sound with button press while the system is
disabled.
e-Grab Handle Lighting
The grab handle is lit continuously. The e-PAD back lighting is lit with a
button press and while training new access and authority codes.