User's Manual
Table Of Contents
- 1. General introduction
- 2. Technical parameters
- 3. Mechanical characteristics
- 4. Operation mode
- 5. Protocol mode
- 6.Function description
- 7.Quick start
- 8. User instruction set
- 8.1 HEX read command description
- 8.2 HEX Parameter description
- 8.3. HEX command data communication format
- 8.4 AT Command
- 8.4.1 AT+DEV
- 8.4.2 AT+EXIT
- 8.4.3 AT+MODE
- 8.4.4 AT+RMODE
- 8.4.5 AT+NWK
- 8.4.6 AT+PANID
- 8.4.7 AT+KEY
- 8.4.8 AT+SHORT_ADDR
- 8.4.9 AT+MAC_ADDR
- 8.4.10 AT+COOR_SHORT_ADDR
- 8.4.11 AT+COOR_MAC_ADDR
- 8.4.12 AT+GET_SHORT_ADDR
- 8.4.13 AT+GROUP
- 8.4.14 AT+CH
- 8.4.15 AT+TXPOWER
- 8.4.16 AT+UART
- 8.4.17 AT+SLEEP
- 8.4.18 AT+DATA_TIME
- 8.4.19 AT+SOFT_ID
- 8.4.20 AT+RESET
- 8.4.21 AT+RESTORE
- 8.3.22 AT+GPIO_PUT
- 8.4.23 AT+RGPIO_PUT
- 8.4.24 AT+GPIO_LEVEL
- 8.4.25 AT+RGPIO_LEVEL
- 8.4.26 AT+PWM
- 8.4.27 AT+RPWM
- 8.4.28 AT+ADC
- 9.User instruction
- 10. Hardware design
- 11. FAQ
- 12. Production guidance
- 13.Antenna information
- 14. Product packaging figure
D2106-THGN01_User Manual
21
Short address of father nodes
:
00 00
(
Short Address=0X0000
)
MAC address of father nodes
:
20 39 EA 0A 00 4B 12 00
Network group number
:
01
Network channel
:
0B
(
channel 11
)
Transmit power
:
04
(
transmit power 4.5dBm
)
Baud rate
:
09
(
baud rate 115200
)
Sleep time
:
05
(
sleep mode starts
,
sleep time is 5s
)
(Notes
:
Father node reserve time is not listed here, please use corresponding command for configuration and
examination.)
8.3. HEX command data communication format
8.3.1. Command format description
Command
(
COM
)
1Byte
Data length
(
LEN
)
1Byte
Data content
(
DATA
)
FC
LEN
DATA
8.3.2. DATA parameter description(data is content awaiting to send)
1
)
Broadcast data
Command:01+type+data
Parameter description:type
01:broadcast mode1 —broadcast the message to all devices in network
02:broadcast mode2 —broadcast the message to receiving devices(except ones in sleep mode)
03:broadcast mode3 —broadcast the message to all functional devices (router and coordinator)
Example
:
FC 05 01 02 31 32 33
Example explanation
:
Transmit HEX data to network broadcast in broadcast mode 2: 0X310X320X33
2)Multicast data
Command:02+ group+data
Parameter description:group
0~99:number for the multicasted message
Example
:
FC 05 02 01 31 32 33
Example explanation
:
Send HEX data to Network Group 1
:
0X31 0X32 0X33