TSM5-28-LS Livestock Alleyway Scale Installation Manual Version 1.
©Triner Scale & Mfg. Co, Inc. 2011. All rights reserved. The information contained herein is the property of Triner Scale and is supplied without liability for errors or omissions. No part may be reproduced or used except as authorized by contract or other written permission. The copyright and the foregoing restriction on reproduction and use extend to all media in which the information may be embodied. Contents subject to change without notice.
TABLE OF CONTENTS Page Chapter 1: 1.1 Chapter 2: Introduction ................................................................................................................ 1-1 Unpacking.................................................................................................................... 1-1 Platform Installation .................................................................................................. 2-1 2.1 Site Preparation....................................................
1.0 INTRODUCTION The TSM5-28-LS scale is a fully electronic weighing system, engineered for years of reliable service. It has four corner-mounted NTEP approved loadcells that are recessed into the scale frame for protection. Also included is a signal-trim summing board enclosed in a watertight junction box. The junction box is accessible from the top of the scale for ease of service and installation.
2.0 PLATFORM INSTALLATION After unpacking the scale, a small amount of preparation is required before the scale can be used for weighing. 2.1 Site Preparation The scale should not be loaded beyond its capacity. Do not select a site where overweight loads would have to cross the platform. Avoid areas where the scale might receive damaging side impacts from wheels or forklift tines.
3.0 CONNECTING THE DIGITAL INDICATOR TO THE PLATFORM The TSM5-28-LS Scale is generally purchased with the TS-700 SS digital indicator. This section covers connecting the TS-700 SS digital indicator with the Alleyway weighing platform. The scale interface cable is pre-wired to the TS-700 SS digital indicator. STEP 1: Access the junction box by removing the screws that secure the access plate on the side of the Alleyway weighing platform. 3.1 Connecting the TS-700 SS Digital Indicator 1.
5. To connect the wires to the terminals, follow the instructions below: a. Using a small Flat head screwdriver, loosen the terminal screws. This will open the terminal clamps so that you can insert the wire. b. Carefully insert the bare end of the wire between the terminal clamps. c. While holding the wire in position, use the screwdriver to tighten the terminal screw. The clamps will close around the wire. After it is tight give the wire a small tug to make sure it’s secure. d.
. Replace the junction box cover. 9. Replace the junction box access plate. 10. Connect the AC adapter to the indicator and then to the wall outlet. If the unit has and AC power cord, connect it to the wall outlet. 11. Turn the Indicator on. After the power up sequence the display should indicate Zero. If it does not, press the ZERO key. 12. When the scale reads Zero it is ready for use.
APPENDIX A: TROUBLESHOOTING AND PERIODIC MAINTAINANCE A.1 Troubleshooting Guide Problem The system does not operate – No Display Possible Problem and Corrective Action • Power disconnected or bad power supply: Check outlet first. Test the AC adapter or power supply. • Indicator fuse blown: Replace fuse, check for cause. • Interface Cable cut or disconnected: Replace or Properly repair cable • Interface Cable wiring problem: Check connections inside junction box and at indicator.
A.2 Periodic Maintenance The TSM Series Low Profile Scale is designed and engineered to require very little maintenance. Follow the basic guidelines below: 1. Periodically clean any debris from under and around the scale. If debris such as broken wood from pallets wedges between the scale platform and the ground or a ramp, erratic weights will result. 2. Provide adequate clearance for free platform movement. Make sure a ramp(s) is not touching the scale.
APPENDIX B: PARTS LIST Part Description Four load cell steel NEMA 4x junction box assembly with signal trim summing card 1/2 –20 precision ball and cup leveling foot 2.5k (2,500 lb) Sheerbeam load cell 5k (5,000 lb) Sheerbeam load cell Load cell Bolt M12 x 1.75 x 50mm Load cell Bolt ½-20 x 1 ¾ Eye Bolt M12 Leveling foot retaining plate, 3” Top access plate screw M8 x 1.
TRINER SCALE & MFG. CO, INC. LIMITED WARRANTY What is Covered: Triner Scale & Mfg. Co. Inc. warrants to the first end user customer of the Triner Scale product enclosed with this limited warranty statement that the product, if purchased and used in the United States, conforms to the manufacturer’s specifications and will be free from defects in workmanship and materials for a period of one (1) year from the date of original purchase.