User's Manual

ManualsBrandsTrio Datacom ManualsElectronicsUHF REMOTE DATA TRANSMITTER

Page 66

E Series Ethernet Radio – User Manual

ER45e

Radio

Frequency Range: 370-520 MHz

(various sub-frequency

bands available)

Frequency Splits: Various Tx/Rx

frequency splits - programmable

Channel Selection: Dual synthesizer,

6.25 kHz channel step

Channel Spacing: 12.5 or 25 kHz

Frequency Accuracy: ±1ppm (-30 to

+60C)(-22 to 140F) ambient

Ageing: <= 1ppm/annum

Operational Modes: Simplex, Half

duplex or Full duplex*

Conﬁguration: All conﬁguration via

Windows based software

Compliances:

ETSI EN300113, EN301489,

EN60950

FCC PART 15, PART 90

IC RS119, ICES-001

ACA AS4295-1995 (Data)

CSA Class I, Division II, Groups

(A,B,C,D) for Hazardous

Locations ANSI/UL

equivalent) Pending.

Transmitter

Tx Power: 0.05 - 5W (+37 dBm)

1 dB User conﬁgurable with

over-temperature and reverse

power protection

Modulation: User conﬁgurable

narrow band digitally ﬁltered binary

GMSK or 4 level FSK

Timeout Timer: Programmable

0-255seconds

Tx Spurious: <= -37 dBm

PTT Control: Auto (Data) / RTS line

on Data Port / System Port Override

Receiver

Sensitivity: -118 dBm for

12 dB SINAD

Selectivity: Better than 60 dB

Intermodulation: Better than 70 dB

Spurious Response: Better

than 70 dB

AFC Tracking: Digital receiver

frequency tracking

Mute: Programmable digital mute

Diagnostics

TVIEW+™ Conﬁguration, Network

Management and Diagnostic

Windows GUI Software

Network wide operation from any

remote terminal.

Non intrusive protocol - runs

simultaneously with the application.

Over-the-air re-conﬁguration of

user parameters.

Storage of data error and channel

occupancy statistics.

In-built Error Rate testing capabilities.

Connections

User Data Ports: 1 x RS232 DB9

female DCE. 300-38,400 bps.

System Port: 1 x RJ45 for diagnostic,

conﬁguration and re-programming.

Ethernet Port: 10/100 Mbps (auto-

MDIX sensing) compliant with

IEEE 802.3

Antenna: N female bulkhead.

Separate N (Tx) and SMA (Rx)

connectors for full duplex.*

Power: 2 pin locking, mating

connector supplied

LED Display: Multimode Indicators

for Pwr, Tx, Rx, Sync, TxD and RxD

data LEDs and LAN LEDs

Ethernet

Protocols: Ethernet/IP (including UDP,

TCP, DHCP, ARP, ICMP, STP, IGMP,

SNTP & TFPT)

Terminal Server: Legacy RS-232

serial support via embedded terminal

server (UDP/TCP).

DHCP Modes: Auto and Manual

Telnet: Telnet access to programming

and diagnostics interface.

SNMP: SNMP V1/V2 access to

diagnostics and radio information

Security

Encryption: 128-bit AES encryption**

Authentication: Optional Trusted

radio authentication using Radius

compliant server

Modem

Data Port: RS232, DCE,

300-38,400 bps asynchronous

System Port: RS232, 19,200 bps

asynchronous

Flow Control: Selectable hardware /

software / 3 wire interface

RF Channel Data Rate:

4800/9600/19,200 bps

Half / Full duplex*

Bit Error Rate:

< 1x10-6 @ -111 dBm (4800 bps)

< 1x10-6 @ -110 dBm (9600 bps)

< 1x10-6 @ -106 dBm (19,200 bps)

Please check with your local TRIO Datacom

representative.

Collision Avoidance: TRIO Datacom’s

unique supervisory ChannelShare™

collision avoidance system

MultiStream™: TRIO Datacom’s

unique simultaneous delivery of

multiple data streams (protocols)

Data Turnaround Time: <10mS

Firmware: upgradable ﬂash based

ﬁrmware.

Local regulatory conditions may determine the

performance and suitability of individual versions

in different countries. It is the responsibility of

the buyer to conﬁrm these regulatory conditions.

Performance data indicates typical values related

to the described unit.

Information subject to change without notice.

** Export restrictions may apply

Note: Not all product features are available

in every mode of operation.

General

Power Supply: 13.8 Vdc nominal

(10-30 Vdc)

Temp Range: -30degC to +60degC

Transmit Current: 750 mA nom. @ 1 W

1600 mA nom. @5 W

Receive Current: <180mA nom

Shutdown Mode: External control,

< 10 mA

Housing: Rugged Diecast Enclosure

Dimensions:

170 x 150 x 42mm

6.7 x 5.9 x 1.65 inches

With Mounting Plate

190 x 150 x 47mm

7.5 x 5.9 x 1.85 inches

Mounting: Fitted Mounting Plate or

DIN rail

Weight: 1.27 kg (2.8lbs.)

Options

ERFD45e Full Duplex Operation

with separate N (Tx) and SMA

(Rx) connectors

DIN Rail mounting kit

Part Number : ER-DIN-KIT*

*Not offered in all countries.