Owner's Manual APS 912 INT APS 1024 INT APS 2012 INT 1111 W. 35th Street Chicago, IL 60609 USA Customer Support: (773) 869-1234 www.tripplite.com APS 2424 INT APS 3636 VRI (208/240V, 50 Hz) Alternative Power Sources • Voltage- and Frequency-Controlled • Peak Power, High Efficiency Español: p. 16 Introduction: p. 2 - 3 Safety: p. 4 Configuration & Connection: Features: p. 5 - 9 p. 10 - 11 Maintenance & Service: p. 12 Warranty: p. 12 Troubleshooting: p. 13 Specifications: p.
Introduction Congratulations! You’ve purchased the most advanced, feature-rich integrated inverter/battery charger on the market. Your APS provides your equipment with utility-supplied AC power when it is available, and during blackouts, overvoltages and brownouts, your APS automatically switches over to an external battery source to power connected equipment with voltage and frequencycontrolled AC power.
Advanced, 3-Stage Battery Charger Stage 1 Bulk Stage 2 Absorption Stage 3 Float Your APS recharges your battery faster than conventional chargers because its three-stage charger profile (Bulk, Absorption and Float) are optimized, regardless of the type of battery you use (Wet or Gel).* In addition, the advanced charging system protects against over-charge and over-discharge to ensure a longer service life from your battery.
Safety This manual contains important instructions and warnings that should be followed during the installation, operation and storage of all Tripp Lite APS Systems. APS Location Warnings • Install your APS indoors, away from excess moisture or heat, dust or direct sunlight. • Leave adequate space around all sides of the APS for proper ventilation. • Do not install the APS near magnetic data storage media, as this may result in data corruption.
Configuration CONFIGURATION DIP SWITCH SETTINGS DIP SWITCH GROUP A (All models) BATTERY TYPE / VOLTAGE POINT Using a small tool, set the 4 "Battery Type / Voltage Point" Configuration DIP Switches, Group A (located on the front panel of your APS; see Diagram 1, p. 33) to select battery type and set the voltage range outside of which your APS will switch to battery power.
DIP SWITCH GROUP B (Available on Select Models) LOAD SHARING/EQUALIZE BATTERY CHARGE Using a small tool, set the "Load Sharing" Configuration DIP Switches, #1 and #2 of Group B (located on the front panel of your APS; see Diagram 1, p. 33). DIP Switch #3, Group B should be kept in the "UP" position when you are not equalizing your batteries' charges. DIP Switch #4, Group B has no function.
Battery Selection Selecting Battery Type Select a battery or system of batteries that will provide your APS with proper DC voltage and an adequate amp hour capacity.* Select ‘Deep-Cycle’ batteries to enjoy optimum performance from your APS. Batteries of either Wet-Cell (vented) or Gel-Cell/Absorbed Glass Mat (sealed) construction are ideal. 6 Volt “golf-cart,” Marine Deep-Cycle or 8D Deep-Cycle batteries are also acceptable.
Battery Connection (Standard) 1. Connect your APS's positive DC Terminal directly to a fuse. UL requires that you install a recognized UL component fuse block and fuse within 18 inches of the battery. The fuse's rating must equal or exceed the Minimum DC Fuse Rating listed in your APS model's specifications on pages 14-15. 2. Choose a battery configuration appropriate to your batteries. • Single Battery Connection: Refer to Diagram 4, page 34.
Hardwired Electrical Connections (All hardwire models) (See Diagram 3, p. 33). Consult a qualified electrician and follow all applicable electrical codes and requirements. HARDWIRE PROCEDURE 1) Loosen screws and remove cover plate from your APS's Hardwire AC electrical box. Remove the knockout covers closest to the desired electrical source and to your equipment. 2) Thread your wires through strain reliefs and through the knockouts.
Switches, Indicator Lights & Other Features (See Diagram 9, p. 35 to locate the following switches, indicator lights and other features.) Switches 1. Operating Mode Switch (All models) This switch selects the APS operating mode (either "AUTO/REMOTE", "OFF" or "CHARGE ONLY"). See "Set Operating Mode Switch", pg. 9 to select the optimum setting for this switch. 2.
8.
Maintenance & Service Maintenance Your APS model requires no maintenance but should be kept dry at all times. Periodically check all cable connections both at the unit and at the battery. Clean and tighten connections as necessary. Service If returning your APS to Tripp Lite, please pack the APS carefully, using the ORIGINAL PACKING MATERIAL that came with the unit. Enclose a letter describing the symptoms of the problem. If the APS is within the warranty period, enclose a copy of your sales receipt.
Troubleshooting Try these remedies for common APS problems before calling for help. Before returning your UPS for service, call Tripp Lite Customer Service at (773) 869-1234 in the USA or at (773) 869-1956 for international customers. SYMPTOM PROBLEMS CORRECTIONS APS does not provide AC output (AC input present). APS not properly connected to utility power. Connect APS to utility power. Circuit breaker is tripped. Reset circuit breaker.
Specifications—Corded Models CORDED MODELS: Weight: INVERTER Continuous power (@ 20° C): Surge power (5 seconds): Efficiency (Full Load): Minimum DC Fuse Rating: DC Input Current @ Nominal V DC Full Load : No Load : Nominal DC Input: DC Input Voltage Range: Nominal Output Volts: Nominal Output Frequency: BATTERY CHARGER Charging Capacity DC: Acceptance Volts DC: Float Volts VDC: Input Voltage AC: Input Current AC: LINE VAC OPERATION Minimum Input AC Volts: Maximum Input AC Volts: Maximum Input Current (Cont
Specifications—Hardwired Models HARDWIRED MODELS: Weight: INVERTER Continuous power (@ 20° C): Surge power (5 seconds): Efficiency (Full Load): Minimum DC Fuse Rating: DC Input Current @ Nominal V DC Full Load : No Load : Nominal DC Input: DC Input Voltage Range: Nominal Output Volts: Nominal Output Frequency: BATTERY CHARGER Charging Capacity DC: Acceptance Volts VDC: Float Volts VDC: Input Voltage AC: Input Current AC: LINE VAC OPERATION Minimum Input AC Volts: Maximum Input AC Volts: Maximum Input Curren
Manual de Operación 1111 W. 35th Street Chicago, IL 60609 USA Servicios a Clientes: (773) 869-1234 www.tripplite.com APS 912 INT APS 1024 INT APS 2012 INT APS 2424 INT APS 3636 VRI (230V, 50 Hz) Fuentes Alternativas de Energía • Con Voltaje y Frecuencia Controlada • Energía de Cresta, Alta Eficiencia Introducción: p. 17 - 18 Seguridad: p. 19 Configuración y Conexión: Características: p. 26 - 28 Mantenimiento y Servicio: p. 28 Garantía: p. 29 Resolución de Problemas: p.
Introducción ¡Felicitaciones! Usted ha adquirido el inversor / cargador de batería integrado más avanzado y con más características en el mercado. Este modelo APS suministrará a sus equipos energía de CA mientras ésta esté presente. Durante un apagón, caída o subida de voltaje, esta unidad cambia automáticamente a la batería externa para suministrar energía de CA de voltaje y frecuencia controlada.
Cargador Avanzado de 3 Etapas para Baterías Etapa 1 Alim Stage 1 entac Bió un lken Ma sa VOLTAJE DE BATERÍA Stage2 2 Etapa Absorption Absorción Etapa 3 Stage 3 Alimentación porFloat Flotador Este sistema APS recargará sus baterías más rápido que otros cargadores convencionales debido a que su perfil de recarga de 3 etapas (Alimentación en Masa, Absorción y Alimentación por Flotador) provee óptimo rendimiento independientemente del tipo de baterías que usted utilice (Húmeda o de Gel).
Seguridad Este manual contiene advertencias e instrucciones importantes que deben seguirse durante la instalación, operación y almacenaje de todos los Sistemas APS de Tripp Lite. Precauciones sobre la Ubicación del APS • Instale este sistema bajo techo, lejos de calor o humedad excesivos, polvo o luz solar directa. • Deje suficiente espacio alrededor del APS para permitir ventilación adecuada.
Configuración Regulación de los Interruptores DIP de Configuración GRUPO A DE INTERRUPTORES DIP (Todos los modelos) TIPO DE BATERÍAS / PUNTOS DE VOLTAJE Usando una herramienta pequeña, ajuste los 4 Interruptores DIP de Configuración, Grupo A: “Battery Type / Voltage Point” (tipo de baterías / punto de voltaje) ubicados en el panel frontal del sistema APS (vea el Diagrama 1, página 33) para seleccionar el tipo de baterías que desea utilizar y programar el rango de voltaje para el cambio automático del sistem
GRUPO B DE INTERRUPTORES DIP (Modelos Selectos) COMPARTICION DE CARGA / IGUALAR CARGA DE BATERIAS Usando una herramienta pequeña, ajuste los Interruptores DIP de Configuración “Load Sharing” (compartición de carga) del Grupo B (ubicados en el panel frontal del sistema APS; vea el Diagrama 1, página 33). El Interruptor DIP No. 3 del Grupo B debe estar en la posición “UP” (hacia arriba) cuando usted no desee igualar la carga de las baterías. El Interruptor DIP No. 4 del Grupo B no posee función alguna.
• Igualar la Carga de Baterías (Interruptores DIP No. 3, Grupo B) Este interruptor DIP se acciona momentáneamente para iniciar el proceso de igualar la resistencia interna de las pilas. Con ello se prolonga la vida útil de algunos tipos de pilas; consulte con el fabricante de sus pilas para conocer si éstas se beneficiarían con dicho proceso. El proceso de igualación de carga es automático y una vez iniciado sólo se puede detener si se interrumpe la alimentación de electricidad.
Paso 4: La capacidad de baterías en Amperios/Hora se indica usualmente para una intensidad de descarga de 20 horas. La capacidad actual en Amperios/Hora es menor cuando la batería se descarga a mayor intensidad. Para compensar por esta diferencia, multiplique el Estimado Aproximado de Capacidad en Amperios/Hora (obtenido en el paso 3) por 1.2 y así determinar el tamaño óptimo en amperios/hora de las baterías que usted debe conectar al sistema APS.
3. Utilice cableado DEL CALIBRE MAS CORTO Y PESADO para la conexión de las baterías Utilice cableado No. 4 para un cable de CD de hasta 10 pies (3 metros) de longitud. Utilice cableado No. 2 para un cable de hasta 16 pies (4.9 metros). El cableado de calibre corto y pesado limita la pérdida de voltaje de CD y permite la transferencia máxima de corriente. * * Los modelos APS incluyen capacidad para entregar una salida más alta en vatios durante breves períodos de tiempo.
2) Enhebre sus alambres a través de los sujetacables y a través de la perforación para este propósito. 3) Conecte los alambres de conexión a tierra de la entrada y la salida a la terminal de conexión a tierra (verde). 4) Conecte el alambre positivo de entrada a la terminal positiva de entrada (café). 5) Conecte el alambre neutro de entrada a la terminal neutra de entrada (azul). 6) Conecte el alambre positivo de salida a la terminal positiva de salida (negra).
Interruptores, Luces Indicadoras y Otras Características (Vea el Diagrama 9 en la página 36 para localizar los siguientes interruptores, luces indicadoras y otras características.) Interruptores 1. Interruptor “Operating Mode” (Modo de operación) Este interruptor selecciona el modo de operación del sistema APS: “AUTO/REMOTE” (automático/ remoto); “OFF” (apagado); “CHARGE ONLY” (recarga solamente). Vea la sección “Conexión de CA” en página 24 para seleccionar la regulación más favorable de este interruptor.
8.
no haya carga conectada. La unidad enciende automáticamente el inversor cuando detecte la presencia de carga. El usuario puede ajustar el potenciómetro de detección de carga (Load Sense Potentiometer) para seleccionar la carga mínima que detectará el APS. Use una herramienta pequeña para girar el potenciómetro en el sentido del reloj si desea reducir la carga mínima a detectar, lo que hará que el inversor se encienda con pequeñas cargas.
Garantía Limitada Tripp Lite garantiza que sus productos estarán libres de defectos en materiales y mano de obra por un período de un año (unidades utilizadas en EE.UU.) ó 120 días (unidades utilizadas fuera de EE.UU) a partir de la fecha inicial de compra. La obligación de Tripp Lite bajo esta garantía está limitada a reparar o reemplazar (a sola discreción de Tripp Lite) los productos defectuosos.
Resolución de Problemas Antes de llamar para pedir ayuda, pruebe estas soluciones para resolver algunos problemas comunes del APS. Antes de enviar el UPS al servicio de reparación, llame al departamento de Atención al Cliente de Tripp Lite, al teléfono (773) 869-1234 en Estados Unidos o al (773) 869-1956 en el caso de nuestros clientes internacionales. SIMTOMA PROBLEMAS SOLUCIONES El sistema APS no suministra salida de CA (energía de CA disponible).
Especificaciones MODELOS CON CABLE: Peso: APS 912 INT 11.9 Kg APS 1024 INT 11.9 Kg INVERSOR Energía continua a 20°C: 900 Vatios 1000 Vatios Energía de sobretensiones transitorias (5 segundos): 1800 Vatios 2000 Vatios Eficiencia (Carga Completa): 89% 89% Indice Mínimo de Capacidad del Fusible CD: 170A 90A Corriente de Entrada de CD a Niveles Nominales Carga Completa: Sin Carga: 85 A 2.6A 47 A 1.
Especificaciones MODELOS CON TOMA DIRECTA AL CIRCUITO: Peso: APS2424 INT 18.5 Kg APS3636 VRI 25.6 Kg INVERSOR Energía continua a 20° C 2400 Vatios 3600 Vatios Energía de sobretensiones transitorias (5 segundos): 4800 Vatios 7200 Vatios Eficiencia (Carga Completa): 89% 89% Indice Mínimo de Capacidad del Fusible: 220A 130A Corriente de Entrada de CD a Niveles Nominales Carga Completa: Sin Carga: 112 A 1.
Diagrams/Esquemas 1 1.2 1.1 See "Configuration", pg. 5. 1.1 is DIP Switch Group A. 1.2 is DIP Switch Group B. Refiérase a la sección “Configuración”, página 20. 1.1 representa el Grupo A de Interruptores DIP. 1.2 representa el Grupo B de Interruptores DIP 2 3 3.3 3.4 3.5 3.6 3.7 3.2 3.1 See Hardwire Electrical Connections, pg. 9. 3.1 is the cover plate, 3.2 is the five-position terminal strip, 3.3 is the output neutral (white), 3.4 is the output hot (black), 3.5 is the ground (green), 3.
4 X Volts 4.1 APS See Battery Connection, Pg.8. 4.1 is the fuse. X = Your APS's Inverter's Nominal Input Voltage. (See specs.) Refiérase a la sección “Conexión de Baterías”, página 23. 4.1 representa el fusible. X = El Voltaje Nominal de Entrada del Inversor del APS. (Vea las especificaciones.) 5 5.1 X Volts X Volts X Volts X Volts APS See Battery Connection, Pg.8. 5.1 is the fuse. X = Your APS's Inverter's Nominal Input Voltage. (See specs.) Refiérase a la sección “Conexión de Baterías”, página 23.
7 7.1 12V 7.3 7.4 7.2 APS Basic 12VDC Vehicular Battery Connection. See Pg.8. 7.1 is the alternator. 7.2 is the vehicle battery ground. 7.3 is the vehicle battery. 7.4 is the fuse. Conexión Básica de Baterías de 12V de CD en Vehículos. Vea página 24. 7.1 representa el alternador. 7.2 representa la conexión a tierra de la batería del vehículo. 7.3 representa la batería del vehículo. 7.4 representa el fusible. 8 12V 8.1 8.2 8.3 8.6 8.4 APS 12V 8.5 8.3 Advanced 12VCD Vehicular Battery Connection.
2 8 14 4 5 6 1 9 15 A. Corded Model Modelo con Cable 13 9 B. Hardwired Model Modelo con Toma Directa al Circuito 10 11 7 3 2 8 14 4 5 6 1 15 13 1. Interruptor “Operating Mode” (Modo de operación) 2. Grupo A de Interruptores DIP (Todos los modelos) 12 3. Grupo B de Interruptores DIP (Modelos selectos únicamente) 4. “LINE” (Línea) (Todos los modelos) 5. “INV” (Inversor ) (Todos los modelos) 6. “LOAD” (Carga Conectada) 7. “CUT/BOOST” (disminuyendo / elevando) (Modelos VR solamente) 8.