pr ch re R W a od an gis e uc ce te gi rr t— to r o st an ww w nlin ra ty w. in a e ti t tri o p p F R o da n lit EE y f : e .
B126-1A1-WP B126-002 B126-004 B126-1A0 B126-1A0-WP-1 B126-1P0 B126-1P0-WP-1 B126-110 Local Unit (L), Remote Unit (R), or Both (B) External Power Supplies (0, 1, or 2) Mounting Hardware Wallplate Screws Screwdriver for Equalization Adjustment HDMI Daisy-chain Cable B126-1A1 Package Contents B B L L R R R R R 2 2 1 1 1 1 0 0 1 X X X X X X X X X X X X X X Product Features All • Support a maximum video resolution of 1080p (60Hz) • Plug-and-play; no software or drivers requ
Product Features B126-1A1 • HDMI over Cat5 Active Extender Kit (Box-style) • Extends a 1080i (60Hz) signal up to 200 ft. from the source, or a 1080p (60Hz) signal up to 150 ft.
Product Features B126-004 • 4-Port HDMI over Cat5 Extender/Splitter Local Transmitter Unit (Box-style) • Splits an HDMI signal into 4 • Features an additional HDMI port, which can be used to connect a local monitor or to daisy-chain additional B126-004 units. Up to 3 B126-004 units can be daisy-chained together to increase the number of connected monitors. • Works with remote/repeater and receiver units to extend an HDMI signal past the 16 ft.
Product Features B126-1A0-WP-1 • HDMI over Cat5 Active Extender Wallplate • Works with B126-002 and B126-004 extender/splitters to extend a 1080i (60Hz) signal up to 200 ft. from the source, or a 1080p (60Hz) signal up to 150 ft.
Product Features B126-110 • HDMI over Cat5 Active Extender Remote/Repeater Unit (Box-style) • Extends and expands Tripp Lite HDMI over Cat5 installation, allowing multiple monitors to be located at different points in a chain of up to 700 ft. • Extends a 1080i (60Hz) signal up to 175 ft., or a 1080p (60Hz) signal up to 125 ft. from the local transmitter unit to the first remote/ repeater unit in the installation • Extends a 1080i (60Hz) signal up to an additional 175 ft.
Mounting Instructions (select models only) The B126-002, B126-004, B126-1A1, B126-1A0 and B126-110 come with mounting hardware that allows them to be mounted in a variety of ways. The following images show the different ways the included mounting brackets can be attached for different mounting methods. Note: The B126-004 can also be mounted to a Tripp Lite B132-004-RB 1U Rackmount Bracket. Up to 3 B126-004 local units can be connected to a B132-004-RB. Wallmount 19” Rackmount 201109206-93-3023-EN.
Standard Extender Kit Installation Notes: 1) Test to make sure the entire installation works properly before pulling cables through ceilings/walls. 2) To achieve maximum distance and performance, use 24 AWG solid wire Cat5e/6 cable. Using stranded wire Cat5e/6 cable, or cable with a gauge (AWG) size higher than 24 AWG, will result in shorter extension distance. Higher gauge cabling, such as 26 AWG, has a more limited transmission capability than lower gauge cabling.
Standard Extender Kit Installation 1 Make sure the HDMI source is powered OFF. 2 Connect the HDMI source to the INPUT port on the B126-1A1 or B126-1A1-WP local unit using a Tripp Lite P568-Series HDMI Cable. 3 Optional for B126-1A1: Connect a local monitor to the LOCAL port on the B126-1A1 local unit using a Tripp Lite P568-Series HDMI Cable.
Extender Kit with Remote/Repeater Installation Notes: 1) Test to make sure the entire installation works properly before pulling cables through ceilings/walls. 2) To achieve maximum distance and performance, use 24 AWG solid wire Cat5e/6 cable. Using stranded wire Cat5e/6 cable, or cable with a gauge (AWG) size higher than 24 AWG, will result in shorter extension distance. Higher gauge cabling, such as 26 AWG, has a more limited transmission capability than lower gauge cabling.
Extender Kit with Remote/Repeater Installation 3 Optional for B126-1A1: Connect a local monitor to the LOCAL HDMI port using a Tripp Lite P568-Series HDMI Cable. 4 Connect the external power supply to the local unit and plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The green LED illuminates to indicate the unit is receiving power from the external power supply. 5 Using Cat5e/6 cable, connect the RJ45 port on the local unit to the RJ45 INPUT port on the B126-110 remote/repeater unit.
Extender Kit with Remote/Repeater Installation 11 To add a third remote/repeater unit, repeat steps 8 through 10. To finish your installation with the B126-1A1 or B126-1A1-WP remote receiver unit, proceed to step 12. 12 Using Cat5e/6 cable, connect the RJ45 OUTPUT port on the last remote/repeater unit to the RJ45 INPUT port of the B126-1A1 or B126-1A1-WP remote receiver unit. 13 Connect a monitor to the HDMI OUTPUT port on the remote receiver unit using a Tripp Lite P568-Series HDMI Cable.
Standard Extender/Splitter Installation Notes: 1) Test to make sure the entire installation works properly before pulling cables through ceilings/walls. 2) To achieve maximum distance and performance, use 24 AWG solid wire Cat5e/6 cable. Using stranded wire Cat5e/6 cable, or cable with a gauge (AWG) size higher than 24 AWG, will result in shorter extension distance. Higher gauge cabling, such as 26 AWG, has a more limited transmission capability than lower gauge cabling.
Standard Extender/Splitter Installation 1 Make sure the HDMI source is powered OFF. 2 Connect the HDMI source to the INPUT port on the B126-002 or B126-004 using a Tripp Lite P568-Series HDMI Cable. 3 Optional for B126-004: Connect an HDMI monitor to the LOCAL port on the B126-004 using a Tripp Lite P568-Series HDMI Cable. 4 Connect the external power supply to the B126-002 or B126-004 local unit and plug it into a Tripp Lite Surge Suppressor, PDU or UPS.
Standard Extender/Splitter Installation 10 Repeat step 9 for each additional monitor you are connecting. 11 Turn on the power to the HDMI source. The orange RJ45 LEDs illuminate on the B126-002 and B126-004 to indicate the unit is receiving a signal from the source. The screen should now be displayed on the connected monitors. 12 If necessary, use the Equalization control on the B126-1A0 or B126-1A0-WP-1 to adjust the video image.
Extender/Splitter with Remote/Repeater Installation Notes: 1) Test to make sure the entire installation works properly before pulling cables through ceilings/walls. 2) To achieve maximum distance and performance, use 24 AWG solid wire Cat5e/6 cable. Using stranded wire Cat5e/6 cable, or cable with a gauge (AWG) size higher than 24 AWG, will result in shorter extension distance. Higher gauge cabling, such as 26 AWG, has a more limited transmission capability than lower gauge cabling.
Extender/Splitter with Remote/Repeater Installation 1 Make sure the HDMI source is powered OFF. 2 Connect the HDMI source to the INPUT port on the B126-002 or B126-004 using a Tripp Lite P568-Series HDMI Cable. 3 Optional for B126-004: Connect a local monitor to the LOCAL HDMI port using a Tripp Lite P568-Series HDMI Cable. 4 Connect the external power supply to the local unit and plug it into a Tripp Lite Surge Suppressor, PDU or UPS.
Extender/Splitter with Remote/Repeater Installation 10 Connect the external power supply to the remote/repeater unit and plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The green power LED and the green RJ45 LEDs illuminate to indicate the unit is receiving power. 11 To add a third remote/repeater unit, repeat steps 8 through 10. To finish your installation with a B126-1A0 or B126-1A0-WP-1 remote receiver unit, proceed to step 12.
Extender/Splitter Daisy-Chain Installation (B126-004 only) Notes: 1) Test to make sure the entire installation works properly before pulling cables through ceilings/walls. 2) To achieve maximum distance and performance, use 24 AWG solid wire Cat5e/6 cable. Using stranded wire Cat5e/6 cable, or cable with a gauge (AWG) size higher than 24 AWG, will result in shorter extension distance. Higher gauge cabling, such as 26 AWG, has a more limited transmission capability than lower gauge cabling.
Extender/Splitter Daisy-Chain Installation (B126-004 only) Level 1 BLU-RAY Level 2 Level 3 OPTIONAL LOCAL MONITOR 201109206-93-3023-EN.
Extender/Splitter Daisy-Chain Installation (B126-004 only) 1 Make sure the HDMI source is powered OFF. 2 Connect the HDMI source to the INPUT port on the B126-004 using a Tripp Lite P568-Series HDMI Cable. 3 Connect the LOCAL port on the B126-004 to the INPUT port on a second B126-004 using the included 1-ft. HDMI daisy-chain cable. 4 Repeat step 3 if you want to connect a third B126-004.
Extender/Splitter Daisy-Chain Installation (B126-004 only) 12 Connect the B126-1P0 HDMI connector to a monitor; or, connect the B126-1P0-WP-1, B126-1A0 or B126-1A0-WP-1 to a monitor using a Tripp Lite P568-Series HDMI Cable. Both the green and orange RJ45 LEDs on the B126-1P0, and the green LED on the B126-1P0-WP-1, illuminate to indicate the unit is receiving power from the connected monitor. 13 Repeat step 12 for each additional monitor you are connecting. 14 Turn on the power to the HDMI source.
Extender/Splitter Daisy-Chain with Remote/Repeater Installation (B126-004 only) Notes: 1) Test to make sure the entire installation works properly before pulling cables through ceilings/walls. 2) To achieve maximum distance and performance, use 24 AWG solid wire Cat5e/6 cable. Using stranded wire Cat5e/6 cable, or cable with a gauge (AWG) size higher than 24 AWG, will result in shorter extension distance.
Extender/Splitter Daisy-Chain with Remote/Repeater Installation (B126-004 only) Up to 175 ft. at 1080i (60Hz) Up to 125 ft. at 1080p (60Hz) Up to 175 ft. at 1080i (60Hz) Up to 125 ft.
Extender/Splitter Daisy-Chain with Remote/Repeater Installation (B126-004 only) 1 Make sure the HDMI source is powered OFF. 2 Connect the HDMI source to the INPUT port on the B126-004 using a Tripp Lite P568-Series HDMI Cable. 3 Connect the LOCAL port on the B126-004 to the INPUT port on a second B126-004 using the included 1-ft. HDMI daisy-chain cable. 4 Repeat step 3 if you want to connect a third B126-004.
Extender/Splitter Daisy-Chain with Remote/Repeater Installation (B126-004 only) 11 Using Cat5e/6 cable, connect the RJ45 OUTPUT port on the first remote/repeater unit to the RJ45 INPUT port on a second remote/ repeater unit. 12 Connect a monitor to the HDMI OUTPUT port on the remote/repeater unit that you just added using a Tripp Lite P568-Series HDMI Cable. 13 Connect the external power supply to the remote/repeater unit and plug it into a Tripp Lite Surge Suppressor, PDU or UPS.
Extender/Splitter Daisy-Chain with Remote/Repeater Installation (B126-004 only) 20 If necessary, use the Equalization control on the remote/repeater unit(s) and remote receiver unit to adjust the video image. Note: An improper Equalization setting can cause the monitor not to display a picture at all. Try each Equalization setting until an acceptable picture is displayed.
WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union) Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations, when customers buy new electrical and electronic equipment from Tripp Lite they are entitled to: • Send old equipment for recycling on a one-for-one, like-for-like basis (this varies depending on the country) • Send the new equipment back for recycling when this ultimately becomes waste WARNING Use of this equipment in life sup