pr ch re R W a od an gis e uc ce te gi rr t— to r o st an ww w nlin ra ty w. in a e ti t tri o p p F R o da n lit EE y f : e .
Package Contents • B126-2A1 Kit or B126-2A0 Receiver Unit • External Power Supply (Input: 100-240V, 50/60Hz, 0.5A Output: 5V, 2A) • Mounting Hardware • Screwdriver for Equalization Adjustment • Owner’s Manual Product Features • Extends an HDMI signal to 2 monitors up to 200 ft. from the source over a single Cat5e/6 cable. • A B126-002 or B126-004 extender/splitter transmitter unit is required for use with the B126-1A0 1x2 receiver unit. • Extends a 1080p (60Hz) signal up to 150 ft.
Product Features • Supports both stereo and 7.1-channel surround sound audio (7.1-channel surround sound signal will be Multi-Channel or PCM). • HDCP and 3D compatible. • Plug and play; No software or drivers required. • Compatible with all operating systems. • Mounting hardware included. Optional Accessories: • B126-110 – Remote Repeater Unit • N202-Series Cat6 24 AWG, Solid Wire Patch Cables • P568-Series High-Speed HDMI Cables 13-08-043 93-32D0.
Mounting Instructions The B126-2A1 and B126-2A0 come with mounting hardware that allows them to be mounted in a variety of ways. The following images show the different ways the included mounting brackets can be attached for different mounting methods. Note: The images below show a B126-1A1 HDMI over Cat5 Receiver Unit, but the mounting hardware installation is the same for the B126-2A1 and B126-2A0. Wall-mount 1 Wall-mount 2 19” Rackmount Pole Mount 13-08-043 93-32D0.
Standard 1 x 2 Extender Kit Installation Notes: 1. Test to make sure that the entire installation works properly before running cables through ceilings/walls. 2. 24 AWG, solid wire Cat5e/6 cable, such as Tripp Lite’s N202-Series, is required to achieve maximum distance and resolution. 3. The diagram below shows the maximum extension distance when using Cat6 cabling. When using Cat5 cabling, the maximum extension distance is 175 ft. at 1080i (60Hz), and 125 ft. at 1080p (60Hz). 4.
Standard 1 x 2 Extender Kit Installation 1 Make sure all devices being connected are powered OFF. 2 Connect the HDMI source to the INPUT port on the transmitter unit using a Tripp Lite P568-Series High-Speed HDMI Cable. 3 Optional: Connect a monitor to the LOCAL port on the transmitter unit using a Tripp Lite P568-Series High-Speed HDMI Cable.
1 x 2 Extender Kit with Remote/Repeater Installation Notes: 1. Test to make sure that the entire installation works properly before running cables through ceilings/walls. 2. The diagram below shows the maximum extension distance when using either Cat5e or Cat6 cabling. 24 AWG, solid wire Cat5e/6 cable, such as Tripp Lite’s N202-Series, is required to achieve maximum distance and resolution. 3. The B126-2A1 is set to transmit a stereo audio signal by default.
1 x 2 Extender Kit with Remote/Repeater Installation 4 Connect the external power supply to the transmitter unit and plug the transmitter unit into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU), or Uninterruptible Power Supply (UPS). The green RJ45 LED illuminates to indicate that the unit is receiving power from the external power supply. 5 Using Cat5e/6 cable, connect the RJ45 port on the transmitter unit marked OUTPUT to the RJ45 port on the B126-110 repeater unit marked INPUT.
1 x 2 Extender Kit with Remote/Repeater Installation To add a third remote/repeater unit, repeat steps 8 through 10. To finish your installation with the B126-2A1 receiver unit, proceed to step 11. 11 Using Cat5e/6 cable, connect the RJ45 port on the repeater unit marked OUTPUT to the RJ45 port on the receiver unit marked INPUT. 12 Connect a monitor to the OUTPUT 1 port on the receiver unit using a Tripp Lite P568-Series High-Speed HDMI cable. 13 Repeat step 12 for the OUTPUT 2 port on the receiver unit.
Standard Extender/Splitter Installation Notes: 1. Test to make sure that the entire installation works properly before running cables through ceilings/walls. 2. 24 AWG, Solid Wire Cat5e/6 cable, such as Tripp Lite’s N202-Series, is required to achieve maximum distance and resolution. 3. The diagram below shows the maximum extension distance when using Cat6 cabling. When using Cat5 cabling, the maximum extension distance is 175 ft. at 1080i (60Hz), and 125 ft. at 1080p (60Hz). 4.
Standard Extender/Splitter Installation REMOTE UNIT MODEL: B126-2A0 HDMI OVER Cat5 1 x 2 EXTENDER B126-2A0 REMOTE UNIT HDMI OVER Cat5 1 x 2 EXTENDER REMOTE UNIT B126-2A0 MODEL: B126-2A0 HDMI OVER Cat5 1 x 2 EXTENDER B126-2A0 MODEL: B126-2A0 REMOTE UNIT MODEL: B126-2A0 HDMI OVER Cat5 1 x 2 EXTENDER Up to 200 ft. at 1080i @ 60Hz (Cat6) Up to 150 ft. at 1080p @ 60Hz (Cat6) B126-2A0 B126-004 BLU-RAY OPTIONAL LOCAL MONITOR 1 Make sure all devices being connected are powered OFF.
Standard Extender/Splitter Installation 7 Connect the external power supply to the receiver unit and plug the receiver unit into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU), or Uninterruptible Power Supply (UPS). The green RJ45 LED illuminates to indicate that the unit is receiving power from the external power supply. 8 Connect a monitor to the OUTPUT 1 port on the receiver unit using a Tripp Lite P568-Series High-Speed HDMI Cable.
Extender/Splitter with Remote/Repeater Installation Notes: 1. Test to make sure that the entire installation works properly before running cables through ceilings/walls. 2. The diagram below shows the maximum extension distance when using either Cat5e or Cat6 cabling. 24 AWG, solid wire Cat5e/6 cable, such as Tripp Lite’s N202-Series, is required to achieve maximum distance and resolution. 3. The B126-002 and B126-004 are set to transmit a stereo audio signal by default.
Extender/Splitter with Remote/Repeater Installation REMOTE UNIT B126-2A0 REMOTE RECEIVER B126-110 REMOTE/ REPEATER B126-110 REMOTE/ REPEATER B126-110 REMOTE/ REPEATER B126-2A0 REMOTE RECEIVER B126-110 REMOTE/ REPEATER B126-110 REMOTE/ REPEATER B126-110 REMOTE/ REPEATER B126-2A0 REMOTE RECEIVER B126-110 REMOTE/ REPEATER B126-110 REMOTE/ REPEATER B126-110 REMOTE/ REPEATER B126-2A0 REMOTE RECEIVER MODEL: B126-2A0 HDMI OVER Cat5 1 x 2 EXTENDER REMOTE UNIT REMOTE UNIT MODEL: B126-2A0 HDMI OVER
Extender/Splitter with Remote/Repeater Installation 5 Using Cat5e/6 cable, connect a RJ45 OUTPUT port on the transmitter unit to the RJ45 INPUT port on the B126-110 repeater unit. 6 Connect a monitor to the HDMI OUTPUT port on the repeater unit using a Tripp Lite P568-Series High-Speed HDMI Cable. 7 Connect the external power supply to the remote/repeater unit and plug the remote/repeater unit into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU), or Uninterruptible Power Supply (UPS).
Extender/Splitter with Remote/Repeater Installation 11 Using Cat5e/6 cable, connect the RJ45 port on the repeater unit marked OUTPUT to the RJ45 port on the B126-2A0 receiver unit marked INPUT. 12 Connect a monitor to the OUTPUT 1 port on the receiver unit using a Tripp Lite P568-Series High-Speed HDMI Cable. 13 Repeat step 12 for the OUTPUT 2 port on the receiver unit.
Troubleshooting If you are unable to get an acceptable image after following the installation instructions, try these troubleshooting tips: 1 Are the external power supplies that came with the product connected and plugged into a working power source? For the product to function properly, it must be connected to and receiving power from the external power supply. 2 Was the power to the connected devices turned off prior to installation? If not, restart them.
Troubleshooting 5 What type of cabling are you using? Inferior cabling can result in poor performance, so it is important that you use cables that support the video resolution you are trying to obtain. To achieve maximum distance and resolution, 24 AWG solid wire UTP cable must be used. Tripp Lite’s N202Series Cat6 Cables are made with 24 AWG solid wire, as are the N02201K-GY (Cat5) and N222-01K-GY Bulk Cables. Also, the HDMI cables you are using must support the resolution you are trying to obtain.
Warranty & Warranty Registration 1-Year Limited Warranty TRIPP LITE warrants its products to be free from defects in materials and workmanship for a period of one (1) year from the date of initial purchase. TRIPP LITE’s obligation under this warranty is limited to repairing or replacing (at its sole option) any such defective products. To obtain service under this warranty, you must obtain a Returned Material Authorization (RMA) number from TRIPP LITE or an authorized TRIPP LITE service center.
FCC Notice, Class B This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.