Owner`s manual

ManualsBrandsTripp Lite ManualsIndoor FurnishingSR42UBSP1

SmartRack

™

Enclosures

Owner’s Manual

WARRANTY

REGISTRATION

to win a FREE Tripp Lite product

www.tripplite.com/warranty

Enclosure Installation

Enclosure Configuration

Equipment Installation

Storage and Service

Warranty and Warranty Registration

Español

Français

1111 W. 35th Street, Chicago, IL 60609 USA

(773) 869-1234 • www.tripplite.com

Preparation

Unpacking

Placement

Leveling

Ground Connection

Adding or Removing Front and Rear Doors

Reversing Front Door

Adding or Removing Roof Panel

Adding or Removing Side Panels

Adjusting Mounting Rails and Cable Management Rails

Combining (Baying) Enclosures

Installing or Removing Cage Nuts

Specifications

Feature Identification

Overview

Important Safety Instructions

Summary of content (14 pages)

PAGE 1
e Y N anc ct T O ch u AN TI r a prod ty R A fo e n AR STR day p Lit arra W I to rip /w G ine T om RE nl E .c E ite o er FR pl st a trip i g in .
PAGE 2
Important Safety Instructions SAVE THESE INSTRUCTIONS All sections of this manual contain instructions and warnings that should be followed during the installation and use of the SmartRack Enclosures described in this manual. Read all instructions and warnings thoroughly before attempting to move, install or use the SmartRack Enclosures described in this manual. Failure to comply will create a risk of personal injury and property damage and may invalidate the warranty.
PAGE 3
Feature Identification 1 2 3 6 4 6 3 7 B A 8 5 Model SR42UB is shown. The other models have similar features, with the differences noted. 1 Roof Panel 2 Locking Split Rear Doors 3 Locking Side Panels (25U enclosures use 2 side panels instead of 4. Side panels are not included with “EXP” models.) 4 Cable Management Rails 5 Casters A and Levelers B 6 Mounting Rails (Provide horizontal and vertical mounting points for equipment.) 7 Keys (One for the doors and one for the side panels.
PAGE 4
Enclosure Installation Caution! Read All Instructions and Warnings Before Installation! WARNING: The rack enclosure is extremely heavy. Do not attempt to unpack, move or install the enclosure without assistance. Until it has been properly installed and stabilized, the enclosure is prone to tipping and could cause property damage and/or personal injury. Use extreme caution when handling the enclosure and be sure to follow all handling and installation instructions.
PAGE 5
Enclosure Installation Unpacking 4 (continued) Use the key to open the enclosure's doors and locate the 2 shipping brackets A that attach the enclosure to the shipping pallet. The brackets are located inside the enclosure. Note: The keys are attached to the front of the enclosure. A 4 5 Use a 13 mm open-end wrench to remove the shipping brackets. Be extremely careful, as the enclosure could shift unexpectedly after bracket removal. Save the brackets and bracket hardware for later use.
PAGE 6
Enclosure Installation Leveling WARNING: Level the enclosure before attempting to install equipment. The casters are not designed to provide long-term support for the enclosure. Use the levelers to provide long-term support. Install the enclosure in a structurally sound area with a level floor that is able to bear the weight of the enclosure, all equipment that will be installed in the enclosure and any other enclosures and/or equipment that will be installed nearby.
PAGE 7
Enclosure Configuration Adding or Removing Front and Rear Doors WARNING: Do not attempt to add or remove doors without assistance. Removing Door 1 Disconnect the door's ground wire. 1 2 Open the door until it is perpendicular (90 degrees) to the front of the enclosure. 90° 2 3 Lift the door from the hinges and remove it from the enclosure.
PAGE 8
Enclosure Configuration Reversing Front Door 3 (continued) Remove the screw and washer from the rear of the door handle and remove the latching mechanism. Rotate the latch washer counter-clockwise 90 degrees and reverse the latch so it points in the opposite direction, then use the screw and washer to re-attach the latch to the rear of the door handle. 3 4 Remove the door by following the steps in the previous section.
PAGE 9
Enclosure Configuration Adding or Removing Roof Panel WARNING: Do not attempt to use the roof panel for weight-bearing purposes other than those explicitly described and approved by Tripp Lite. Do not attempt to add or remove the roof panel without assistance. Removing Roof Panel 1 Pull the 2 pins near the rear of the roof panel. While holding the pins, push the roof panel upward. 1 2 1 2 Remove the roof panel tabs A from the roof panel attachment slots B in the enclosure frame.
PAGE 10
Enclosure Configuration Adding or Removing Side Panels 3 (continued) Lift the panel away from the brace that supports it. To Reinstall Side Panel, Reverse Steps 1-3 3 Adjusting Mounting Rails and Cable Management Rails WARNING: Do not attempt to adjust rails without assistance. Do not attempt to adjust rails while equipment is installed in the enclosure. Do not attempt to use rails without screws installed (6 per rail).
PAGE 11
Enclosure Configuration Combining (Baying) Enclosures WARNING: Combining enclosures is not a substitute for stabilizing the enclosures. Each enclosure in a bay of combined enclosures requires the same stabilizing measures as a standalone enclosure. 1 Arrange the enclosures in the correct position for baying. 1 2 Each enclosure includes 4 baying brackets A that correspond to baying connection points B on the adjoining enclosure. The baying connection points already contain screws.
PAGE 12
Equipment Installation Installing or Removing Cage Nuts WARNING: The flanges of the cage nuts should engage the sides of the square opening in the rail, not the top and bottom. Follow the instructions in your equipment documentation to ensure proper installation of your equipment. Installing Cage Nuts 1 22 Locate the numbered square openings in the mounting rails where you plan to install your equipment.
PAGE 13
Specifications Model SR25UB SR25UBEXP SR25UBSP1 SR25UBEXPSP1 SR42UB SR42UBEXP SR42UBSP1 SR42UBEXPSP1 SR48UB SR48UBEXP SR48UBSP1 SR48UBEXPSP1 Load Capacity* Static Rolling 3000 lb 2250 lb (1363 kg) (1022 kg) 3000 lb 2250 lb (1363 kg) (1022 kg) 3000 lb 2250 lb (1363 kg) (1022 kg) 3000 lb 2250 lb (1363 kg) (1022 kg) 3000 lb 2250 lb (1363 kg) (1022 kg) 3000 lb 2250 lb (1363 kg) (1022 kg) 3000 lb 2250 lb (1363 kg) (1022 kg) 3000 lb 2250 lb (1363 kg) (1022 kg) 3000 lb 2250 lb (1363 kg) (1022 kg) 3000 lb 2250 lb
PAGE 14
1111 W. 35th Street, Chicago, IL 60609 USA 773.869.1234 (USA) • 773.869.1212 (International) www.tripplite.