Owner`s manual

ManualsBrandsTripp Lite Manualschassis componentsSRLADDERATTACH

Owner’s Manual

SmartRack

™

Accessories

Model: SRLADDERATTACH

1 – Introduction 2

4 – Installation 2

4-2 Mounting the Bracket 3

4-5 Perpendicular Rack Attachment (2-Post Racks) 5

2 – Parts List 2

3 – Important Safety Instructions 2

4-1 Planning 2

4-4 Parallel Rack Attachment 4

4-3 Attaching the Ladder 3

4-6 Perpendicular Rack Attachment (4-Post Racks) 6

5 – Storage and Service 8

6 – Warranty and Warranty Registration 8

Tripp Lite World Headquarters

1111 W. 35th Street, Chicago, IL 60609 USA

www.tripplite.com/support

WARRANTY

REGISTRATION:

chance to win a FREE Tripp Lite

product—www.tripplite.com/warranty

Summary of content (8 pages)

PAGE 1
: ty n or a Lite nty f p rra y ip a da Tr w n o Owner’s Manual / arra ne t REE .com i W istratio nl F ite egter o in a rippl R is o w .
PAGE 2
1 – Introduction SRLADDERATTACH works in conjunction with the SRCABLELADDER to provide roof-mounted cable routing from Tripp Lite’s SmartRack Enclosures to a wall, or between 2- and 4-Post Open Frame Racks in either parallel or perpendicular configurations. Now, cable bundles can span aisles, spaces between enclosures in the same row and to spaces not occupied by another rack enclosure.
PAGE 3
4 – Installation (continued) 4-2 Mounting the Bracket (Wall-Mounting) After measuring for distance and modifying the SRCABLELADDER parts, mount the SRLADDERATTACH wall bracket to a wall or other appropriate surface with user supplied bolts. The bracket’s pre-drilled holes are .433 inches (11 mm) in diameter and are spaced 18.819 inches (478 mm)/or 16 inches (406 mm) apart. ) 9 .81 18 8 (47 mm ) 16 6 (40 mm Warning: Be sure to mount the bracket in a location able to bear the load.
PAGE 4
– Installation (continued) 4-4 Parallel Rack Attachment (2-Post or 4-Post Racks) If attaching an SRCABLELADDER in a parallel configuration between two Tripp Lite 2-Post or 4-Post Open Frame Racks, you will need all four M8 Threaded J-Hooks and four M8 Hex Nuts and Washers. The mounting bracket included in this kit for wall mounting should already be installed on both 2- and 4-Post Racks (Tripp Lite brand).
PAGE 5
4 – Installation (continued) 4-5 Perpendicular Rack Attachment (2-Post Racks) Step 1. In order to make perpendicular attachments to a 2-post rack, you will first need to install the Perpendicular Junction Plate. To do so, simply secure the Junction Plate to the two top mounting brackets on the 2-post rack (Tripp Lite brand) using two M8 Hex Head Machine Screws, M8 Washers and M8 Hex Nuts. Note: Diagram is showing the installation of two separate SRLADDERATTACH and SRCABLELADDER units.
PAGE 6
4 – Installation (continued) 4-6 Perpendicular Rack Attachment (4-Post Racks) Step 1. In order to make perpendicular attachments to a 4-post rack, you will need to utilize two Adjustable J-Hook Clamps. To make perpendicular attachments between two 4-post racks, you will need all four Adjustable J-Hook Clamps. Extend the SRCABLELADDER between your two intended racks (or wall). Take one of the Adjustable J-Hook Clamps and insert one of the J-Hooks into its hole.
PAGE 7
4 – Installation (continued) 4-6 Perpendicular Rack Attachment (4-Post Racks) (continued) As stated earlier, you can make SRCABLELADDER attachments to walls and between racks in parallel or perpendicular configurations.
PAGE 8
5 – Storage and Service Storage The unit must be stored in a clean, secure environment with a temperature less than 40° C (104° F) and a relative humidity less than 90% (noncondensing). Store the unit in its original shipping container if possible. Service Your Tripp Lite product is covered by the warranty described in this manual. A variety of Extended Warranty and On-Site Service Programs are also available from Tripp Lite. For more information on service, visit www.tripplite.com/support.