Installation guide

ManualsBrandsTriton Systems ManualsOtherRL5000 Xscale Series

LIGHTED LOW/MIDTOPPER

FIELD INSTALLATION GUIDE

MODELS 8100/9100/97XX/RL5000 (X-SCALE/XP)

CORPORATE HEADQUARTERS: RMA (RETURN MATERIAL AUTHORIZATION)

RETURN ADDRESS:

522 E. Railroad Street 21405 Avenue “B”

Long Beach, MS 39560 Long Beach, MS 39560

Phone: (228) 868-1317

Fax: (228) 868-0437

Systems of Delaware, Inc. is an operating company of Dover Electronics, Inc., a

subsidiary of Dover Corporation (NYSE-DOV). DOVER, the DOVER logo and the

Dover family of marks and TRITON, the TRITON logo and the Triton family of

marks are registered trademarks of Delaware Capital Formation. Inc., a wholly owned

subsidiary of Dover Corporation.

VERSION 4.0

TDN 07102-00043D 08/2006

Summary of content (10 pages)

PAGE 1
LIGHTED LOW/MIDTOPPER FIELD INSTALLATION GUIDE MODELS 8100/9100/97XX/RL5000 (X-SCALE/XP) VERSION 4.0 TDN 07102-00043D 08/2006 CORPORATE HEADQUARTERS: RMA (RETURN MATERIAL AUTHORIZATION) RETURN ADDRESS: 522 E. Railroad Street Long Beach, MS 39560 Phone: (228) 868-1317 Fax: (228) 868-0437 21405 Avenue “B” Long Beach, MS 39560 COPYRIGHT NOTICE © 2002 - 2006 Delaware Capital Formation, Inc. All Rights Reserved. Triton Systems of Delaware, Inc. is an operating company of Dover Electronics, Inc.
PAGE 2
LIGHTED LOWTOPPER - FIELD INSTALLATION GUIDE IMPORTANT NOTICE Triton Systems has discontinued offering a ballast/bulb (AC-powered) topper signage for production model 8100, 9100, and RL5000 (X-Scale/XP) units. LED-lit (DC-powered) signage will be the only available option. The AC-powered toppers will be available for field replaceable parts and repair until inventory is depleted. This manual will show the installation of the topper as well as the power connections for both powered signage.
PAGE 3
LIGHTED LOWTOPPER - FIELD INSTALLATION GUIDE TOPPER INSTALLATION PROCEDURE These procedures are completed with the terminal AC power OFF. 1. Remove the topper assembly from the shipping container. NOTE: If the topper power cord will be routed outside the ATM cabinet, see the procedure on Page 8 for instructions on routing the power cord through the topper rear panel access hole. 2. Locate the mounting holes on the top of the ATM cabinet, as shown in Figure 1. Note that dome plugs cover the openings.
PAGE 4
LIGHTED LOWTOPPER - FIELD INSTALLATION GUIDE Figure 4. Topper on cabinet. Note location of mounting studs. Figure 3. Place topper on cabinet. Slide topper back until it stops. 7. Obtain four #8-32 nuts from the accessory bag. Place the nuts on the mounting studs and tighten using a 3/8" nut driver to secure the topper assembly to the cabinet, as shown in Figure 5 (below). 8. Insert the included snap bushing into the hole, as shown in Figure 6. Figure 5.
PAGE 5
LIGHTED LOWTOPPER - FIELD INSTALLATION GUIDE 9. Connect the topper power cord. Ensure the ATM power switch is turned OFF before connecting! DC CONNECTIONS (LED-LIT TOPPER) Plug the DC power cord (molex connector) from the topper into any available DC output connector on the power supply (*see Notes) as shown in Figures 7a-7e. 1 Note: The dispensing mechanism uses the largest molex connection on the power supply. 2 Note: Model RL5000XP only. The DC power cord may be an 8-pin or 2-pin molex connector.
PAGE 6
LIGHTED LOWTOPPER - FIELD INSTALLATION GUIDE Figure 7e. Model RL5000 (XP) GPIO assy Figure 7f. 2Note: Model RL5000 (XP) 3 Note: 9100 w/TDM or Minimech - Locate the Power Extension cable (splitter) included in kit (Figure below). The cables connectors are marked. Disconnect the Main boards power input (Figure 7g) and connect to one leg of the extension cable. Connect the toppers DC power cable to the other leg (Figure 7h). Reconnect this power cable assembly back to the main board.
PAGE 7
LIGHTED LOWTOPPER - FIELD INSTALLATION GUIDE Figure 7g. Main board power disconnected. Figure 7h. Power extension cable with topper and main board power cables connected. LED Topper Main Board Power Supply Figure 7i. Power extension cable configuration. 10. Turn the power supply to ON (I). The topper sign should light up. Close and lock the control panel.
PAGE 8
LIGHTED LOWTOPPER - FIELD INSTALLATION GUIDE AC CONNECTIONS (BALLAST/BULB TOPPER) Plug the AC power cord into the ATMs power supply, as shown in Figures 8a -8c. Figure 8a. Model 9100 Figure 8b. Model 97XX Figure 8c. Model RL5000 CONNECTING THE TOPPER POWER CORD FOR EXTERNAL ROUTING (AC ASSEMBLY ONLY) 1. 2. Lay the topper assembly on a flat surface, rear side up, as shown in Figure 1. Note the location of the dome plug.
PAGE 9
LIGHTED LOWTOPPER - FIELD INSTALLATION GUIDE 3. Carefully flip the entire assembly over, so that the front side is up. Lift the front of the topper assembly away from the rear half. It may be necessary to tilt the panel to clear the four mounting studs. 4. Press in on the locking tabs to release the dome plug and remove the plug from the rear panel. Feed the power cord through this hole, Figure 2. Route power cord through as shown in Figure 2. rear panel access hole. 5.
PAGE 10
LIGHTED LOWTOPPER - FIELD INSTALLATION GUIDE Instructions for Checking the Topper Light Bulb (AC powered topper only!) 1. Lay the topper on a flat surface, rear side up, as shown in Figure 1. Remove the screws that hold the front and rear panels of the assembly together. 2. Carefully flip the entire assembly over, as shown in Figure 2, so that the sign panel is up. Lift the sign panel up and away from the rear half. It may be necessary to tilt the panel to clear the four mounting studs.