MODEL FT7000XP “FULL FUNCTION ATM” SITE PREPARATION / INSTALLATION GUIDE TDN 07102-00072C Jun 1 2009 CORPORATE HEADQUARTERS: 522 E. Railroad Street Long Beach, MS 39560 Phone: (228) 868-1317 Fax: (228) 868-0437 COPYRIGHT NOTICE © 2008 Triton. All Rights Reserved. TRITON logo is a registered trademark of Triton Systems of Delaware.
DOCUMENT UPDATES Sep 2007 Apr 10 2009 Jun 1 2009 Original Added changes to illustrations on pages 23 and 24 to provide better guidance in creating the wall opening. Edit illustration on pg 18 for minimum service requirements. Added removal of shipping thumb screws in Motorized tray, Depository, and Printer assemblies on pg 38,39.
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE INTRODUCTION The Triton FT7000XP is a self-serviced, weatherized terminal adaptable for any suitable exterior wall or vestibule location. The cabinet designs allow flexibility for walk-up (wall thickness up to 14") or drivethrough ( wall thickness up to 12") installations. Built-in leveling feet allow the unit to be raised to the desired height of the wall opening.
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE CONTENTS TABLE OF CONTENTS ............................................................................................. 4-5 SITE COMPLIANCE .................................................................................................... 6 ENVIRONMENTAL PRECAUTIONS ................................................................................. 7 TEMPERATURE / POWER / RF INTERFERENCE REQUIREMENTS .......................................................
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE CONTENTS POWER AND COMMUNICATION .................................................................................. 51 CONNECT POWER / COMMUNICATION CABLES ........................................................................................ 52 POWER-UP THE UNIT ........................................................................................................................... 53 ENVELOPE SUPPLY UNIT .............................................
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE SITE COMPLIANCE This document contains the information necessary for the preparation and installation of an FT7000XP Triton ATM. It’s important that the site complies with the requirements specified in this document. In addition, electrical wiring and mechanical systems must also comply with all relevant laws and regulations.
ENVIRONMENTAL PRECAUTION CHECKLIST 7
ATM ENVIRONMENTAL PRECAUTIONS CHECKLIST When installing an ATM, some general environmental and power precautions need to be considered. Evaluate the location where the ATM will be installed. To help ensure proper operation of the ATM, ensure the environmental criteria listed in this checklist are met. TEMPERATURE/HUMIDITY 1. Dedicated source. The ATMs AC power feed will be a dedicated line to which no other electrical devices are connected.
DIMENSIONS NOTE Dimensions listed comply with US Federal ADA Guidelines. For USA installations, check for additional guidance. For non-USA installations, check regulations relating to the country of install.
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE PHYSICAL DIMENSIONS Front View LEVEL 1 (VAULT) BUSINESS HOURS Overhead View * Subtract 2" [51mm] for Drive-up ATM BUSINESS HOURS / LEVEL 1 (VAULT) 10
SITE PREPARATION / INSTALLATION PHYSICAL DIMENSIONS Side View * Subtract 2" [51mm] for Drive-up ATM Plinth Adjustments (represented by the value of 'X') Minimum Maximum 1 - 5/8" [41 mm] 12" [305 mm] Note: In order to move the ATM by sliding a pallet jack betw een the vault and the plinth, 'X' must be at least 4" [102 mm].
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE PHYSICAL DIMENSIONS [843] 33 - 3/16" Rear View BUSINESS HOURS 2-D OOR [1449] 57 - 1/16" LEVEL 1 (VAULT) 2-D OOR LEVEL 1 (VAULT) 1-D OOR [843] 33 - 3/16" [1534] 60 - 3/8" [1534] 60 - 3/8" 12 [843] 33 - 3/16"
SITE PREPARATION / INSTALLATION PREFERRED SERVICE AREA DIMENSIONS LEVEL 1 (VAULT) - 1 DOOR DOOR SWING 180° * * Subtract 2" [51mm] for Drive-up ATM 13 Subtract 2" [51mm] for Drive-up ATM
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE PREFERRED SERVICE AREA DIMENSIONS BUSINESS HOURS / LEVEL 1 (VAULT) - 2 DOOR * DOOR SWING 180° DOOR SWING 180° * Subtract 2" [51mm] for Drive-up AT M 14 Subtract 2" [51mm] for Drive-up ATM
SITE PREPARATION / INSTALLATION MINIMUM SERVICE AREA DIMENSIONS BUSINESS HOURS - 2 DOOR NOTE: THIS CABINET ONLY AVAILABLE WITH FUJITSU DISPENSING MECHANISM DOOR SWING 90° DOOR SWING 90° * * Subtract 2" [51mm] for Drive-up ATM 15 Subtract 2" [51mm] for Drive-up ATM
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE MINIMUM SERVICE AREA DIMENSIONS LEVEL 1 (VAULT) - 2 DOOR (FUJITSU DISPENSER) DOOR SWING 120° DOOR SWING 100° * * Subtract 2" [51mm] for Drive-up ATM 16 Subtract 2" [51mm] for Drive-up ATM
SITE PREPARATION / INSTALLATION MINIMUM SERVICE AREA DIMENSIONS LEVEL 1 (VAULT) - 2 DOOR (NMD-100 D ISPENSER) DOOR SWING 110° DOOR SWING 100° * * Subtract 2" [51mm] for Drive-up ATM 17 Subtract 2" [51mm] for Drive-up ATM
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE MINIMUM SERVICE AREA DIMENSIONS LEVEL 1 (VAULT) - 1 DOOR (FUJITSU D ISPENSER) 18
SITE PREPARATION / INSTALLATION MINIMUM SERVICE AREA DIMENSIONS LEVEL 1 (VAULT) - 1 DOOR (NMD-100 DISPENSER) DOOR SWING 125° * * Subtract 2" [51mm] for Drive-up ATM 19 Subtract 2" [51mm] for Drive-up ATM
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE CUSTOMER ACCESS DIMENSIONS Walk-up ATM Customer Access Dimensions (Walk-up ATM) Feature Height Height (Business Hours) (Level 1 - Vault) Control panel Depth 1 Top Function Key 37 - 1/4" (947 mm) 40 - 9/16" (1030 mm) 6" (152 mm) 2 Cash Dispenser 28 - 9/16" (725 mm) 31 - 7/8" (810 mm) 5.
SITE PREPARATION / INSTALLATION CUSTOMER ACCESS DIMENSIONS Drive-up ATM Customer Access Dimensions (Drive-up ATM) Feature Control panel Height Height (Business Hours) (Level 1 - Vault) 39 - 7/8" (1013 mm) 3.1" (79 mm) Depth 1 Top Function Key 36 - 9/16" (929 mm) 2 Cash Dispenser 28 - 9/16" (725 mm) 31 - 7/8" (810 mm) 3.7" (94 mm) 3 #5 K ey (Main Keypad) 25" (636 mm) 28 - 5/16" (719 mm) 2.7" (69 mm) 4 Envelope Depository 27 - 5/8" (701 mm) 30 - 15/16" (786 mm) 1.
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE WALL OPENING / HEIGHT REQUIREMENTS (EXTERIOR WALL) (CRITICAL) The Difference in Elevation is the most critical dimension to consider when installing the FT7000. Use whatever method you feel comfortable with to determine this dimension. To meet ADA outside height requirements, refer to the chart below and figures on the following pages. The size of the opening will not change, but its vertical position will to meet these requirements.
SITE PREPARATION / INSTALLATION DIAGRAM A DIFFERENCE IN ELEVATION (INSIDE FLOOR/EXTERIOR GROUND) LESS THAN 10-11/16" (272 MM) To meet ADA requirements: Note: Dimension ‘A’ must not exceed 30 - 3/4" [781 mm]. Dimension ‘B’ = Dimension ‘A’ minus the difference in elevation. Dimension ‘A’ is the distance from the bottom of the tube to the exterior ground. Dimension ‘B’ is the distance from the bottom of the tube to the interior floor.
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE DIAGRAM B DIFFERENCE IN ELEVATION (INSIDE FLOOR/EXTERIOR GROUND) GREATER THAN 10-11/16" (272 MM) If the interior surface is greater than 11 inches higher than the exterior, the leveling feet might not retract sufficiently to meet the ADA requirement. In this case a ramp will be required outside. Ensure it meets ADA specifications for access.
INSTALLATION 25
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE BEFORE YOU START It’s recommended that the unit be secured to the facility floor. The footprint of the cabinet floor allows for securing the unit through the leveling feet “plinth” hardware, regardless of how high the unit may be raised. It is the customer or their agent’s responsibility to determine how/where the unit is affixed to the facility.
SITE PREPARATION / INSTALLATION TOOLS REQUIRED Tools / Items Recommended Lifting/moving devices (pallet jack, forklift, lifting jack/trolley, etc) Crowbar / roll bars, scrap lumber (blocking) Tape measure / bubble level / framing square Hammer / chisel Back support belt / safety goggles,/mask steel-toed shoes Marker / pencil Tool kit consisting of: Adjustable wrench (large), box wrenches (open / closed) - up to 1-1/4" (32 mm) magnetic phillips / flattip screwdrivers, nutdriver set, diagonal cutters, e
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE UNPACKING THE UNIT *** WARNING *** The FT7000 XP unit is slightly top heavy. USE EXTREME CAUTION! Always move/support the unit from the FRONT! 2-personnel are recommended when unpacking and moving the unit!! 1. The FT7000XP will be secured on a wooden pallet. Move the pallet using a pallet jack/forklift to the desired location before unpacking. 2.
SITE PREPARATION / INSTALLATION NOTE: COMPLETE THE FOLLOWING STEPS TO REMOVE THE SHIPPING BRACKETS AND RETAINING SCREWS BEFORE CONTINUING THE INSTALLATION AND INITIAL OPERATIONAL CHECKOUT. REMOVE / INSTALL F510 DISPENSER The F510 dispensing mechanism is shipped inside the security vault (see section in this manual under “COMBINATION LOCK” for opening lock mechanism). There are shipping brackets that secure the assembly inside the cabinet and on the slide tray.
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE 4. REMOVE SLIDE TRAY BRACKETS: Remove the two (2) thumbscrews that secure the dispenser keeper brackets to the slide tray (each side). Remove the brackets. RETAIN THE BRACKETS/THUMBSCREWS! * REMINDER * AFTER REINSTALLING THE DISPENSER ON THE SLIDE TRAY, THE BRACKETS AND THUMBSCREWS MUST BE REINSTALLED FOR SECURING UNIT TO SLIDE TRAY! 5. REMOVE DISPENSER SECURITY MODULE: Disconnect the three (3) connectors shown from the dispenser circuit board.
SITE PREPARATION / INSTALLATION 6. REMOVE DISPENSER FROM CABINET: With 2 persons, grasp the dispenser in the areas shown (GREEN tape strips) and lift off the tray. See weight table and warning before removal of the dispenser. Set dispenser aside. Weight of the F510 Dispenser *** WARNING *** Two persons highly recommended to remove the dispenser from the cabinet. When removing dispenser from cabinet, use caution not to damage the throat extension on front of dispenser mechanism.
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE INSTALLING THE F510: Note: Before proceeding, ensure the dispenser Security module and its attached cable track are out of the way (see Pg.30, step 5). *** WARNING *** Two persons highly recommended to install the dispenser in the cabinet. When installing the dispenser, use caution not to damage the throat extension on front of dispenser mechanism. 1. Push down on the dispenser tray latch (Green) and extend the slide tray fully, locked position. 2.
SITE PREPARATION / INSTALLATION 5. Once again, push down on the dispenser tray latch (Green) and extend the slide tray fully, locked position. 6. Remount the dispenser keeper brackets and secure with the thumbscrews (2, each side). The flange on the brackets press up against the edge of the black plastic guide rail. 7. Reconnect the dispenser Security module to the dispenser. Next, reconnect the cables to the dispenser circuit board. Note: See mounting/connection locations on Pg. 30, step 5. 8.
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE REMOVE / INSTALL NMD-100 DISPENSER The NMD-100 dispensing mechanism is shipped inside the security vault (see section in this manual under “COMBINATION LOCK” for opening lock mechanism). Follow the procedures below for removal. REMOVING THE NMD-100: 1. Open the lower right rear cabinet door (2-door) or lower cabinet door (1-door). 2. EXTEND DISPENSER TRAY: Pull up on the tray locking pin and extend the tray fully.
SITE PREPARATION / INSTALLATION 3. D ISCONNECT POWER / DATA/ SHUTTER CABLES : Disconnect the three (3) cables from the dispenser and route them out the cable entry side. Note: If the data and shutter cables are ty wrapped to the dispenser cover, you will have to cut the ty wrap. Power Shutter Data 4. REMOVE DISPENSER SECURITY MODULE: Pull up on the security module bracket locking pin shown.
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE 5. REMOVE DISPENSER FROM CABINET: With 2 persons, grasp the dispenser lift handles and lift dispenser off the slide rails. Set dispenser aside. *** WARNING *** Two persons highly recommended to remove the dispenser from the cabinet. When removing dispenser from cabinet, use caution not to damage the throat extension on front of dispenser mechanism.
SITE PREPARATION / INSTALLATION INSTALLING THE NMD-100: Note: Before proceeding, ensure the dispenser Security module and its attached cable track are out of the way (see Pg.35, step 4). *** WARNING *** Two persons highly recommended to remove the dispenser from the cabinet. When removing dispenser from cabinet, use caution not to damage the throat extension on front of dispenser mechanism. 1. Extend the slide rails out fully. With 2 persons, lift and set mechanism on the rails.
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE ENVELOPE DEPOSIT BIN 1. Open the lower left rear cabinet door (2-door) or lower cabinet door (1-door). 2. REMOVE SHIPPING THUMBSCREW / BIN: Remove the shipping thumbscrew that is secured to the deposit bin. You may either discard the screw or retain for future shipment. Grasp the handle and pull depository bin from cabinet. MOTORIZED TRAY / DEPOSITORY / PRINTER Remove the GREEN thumb screws used to retain the above items during shipment.
LEVELING FEET The leveling rods (4) that adjust the plinth height are located in the bottom of the cabinet. To adjust for height corrections: Loosen the inside nuts. Note: There are only three (3) rods that have these attached. Adjust the bottom nut (under the cabinet) to raise/lower unit Note: 12” (305mm) maximum. Retighten inside nut.
SITE PREPARATION / INSTALLATION INSTALLING UNIT / COLLAR HARDWARE STEP 1: Slide the unit’s tube section through wall opening. Let it protrude slightly out the front (exterior) wall. NOTE DO NOT install the collar bracket hardware (4brackets) or control panel collar prior to moving unit through wall opening. STEP 2: Start the nuts supplied to each of the four (4) collar brackets (2 nuts per bracket). Temporarily slide the collar brackets to the tube front. Bracket P/Ns are listed in table below.
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE STEP 3: Move unit so collar brackets are as close to flush against wall. Note: If there are uneven gaps between brackets and wall (ex: larger gap on bottom), this may be tightened by adjusting leveling feet after unit is anchored. STEP 4: Inside facility - lower the leveling feet (plinth assembly) to the interior floor, if applicable. Mark the anchor holes. See dotted lines below for anchor hole placement.
SITE PREPARATION / INSTALLATION STEP 6: SECURING COLLAR BRACKETS: (Inside facility) Open the upper right side rear cabinet door. Unlock and pull the green handle shown. This will release the control panel latch. (Outside facility) Grasp the control panel on both sides and slowly pull it out to its full extension (the left side will lock in place).
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE STEP 7: INSTALLING / SECURING CONTROL PANEL COLLAR (Outside facility - Control panel extended / open). Locate the control panel collar assembly. Align the trim tabs located on back of assembly (2 - each side) with the slotted openings of the control panel. Insert tabs and push down slightly. (Top of control panel) Loosen thumbscrew and remove enclosure lid shown to gain access to control panel GPIO docking board.
SITE PREPARATION / INSTALLATION STEP 8: CLOSE CONTROL PANEL: Pull up on the green tipped drop-in pin and slowly swing the front control panel around until it’s parallel to the cabinet sleeve. Grasp the side edges of the control panel collar and slowly guide the control panel into the cabinet sleeve. Note: Ensure the guide roller lines up in it’s track when closing the control panel.
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE STEP 9: SEALING THE COLLAR BRACKETS: A good weather seal is required between the exterior wall and the collar bracket hardware installed in Step 6. DO NOT seal around the control panel collar as this has a water-resistant gasket factory installed. A suitable water-resistant sealant product must be applied to three (3) sides of the collar brackets hardware. If using caulk, recommend a clear color (not white).
ELECTRONIC LOCK 46
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE ENTERING THE COMBINATION The electronic lock combination(s) consists of six digits. Upon arrival, the combination(s) of the lock should already be set at 1-2-3-4-5-6. After installation of the unit has been completed, perform the following steps: 1. Enter the preset combination(s) and check for proper operation. After each keypress, the lock will beep. After the final digit has been entered, the lock will beep twice and the open period will begin. 2.
ELECTRONIC L OCK PROGRAMMABLE FEATURES The locks are initially set with the standard features (a single 6-digit code). Based on your requirements, additional features may be added in the lock, BUT THEY MUST BE PRE-PROGRAMMED by Triton prior to shipment of the unit. The programmable features are listed below. Manager (Factory set to 1-2-3-4-5-6): Add/remove second user Enable/disable second user Time Delay: Delay period 1-99 minutes.
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE REINSTATE USER (Manager feature only) - Always perform this operation with the door(s) open! 1. Enter Manager Code and HOLD DOWN LAST DIGIT OF CODE until the lock signals with two (2) sets of double beeps. 2. PRESS 1. Lock signals once. User is now reinstated. 3. If a mistake is made, wait thirty (30) seconds and repeat steps 1 and 2. REMOVE USER (Manager feature only) - Always perform this operation with the door(s) open! 1.
ELECTRONIC LOCK TIME DELAY (if feature is programmed) - Always perform this operation with the door(s) open! 1. Enter valid code. • • Delay period starts (1-99 minutes pre-programmed). LED flashes RED at one (1) second intervals. - If valid code entered during delay, Delay period restarts. - If invalid code(s) entered during delay, Delay period aborts. 2. At end of delay period, Open period starts (1-19 minutes pre-programmed). • • 3. LED flashes RED at 1/2 second intervals.
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE CHANGING THE BATTERY 1. Open the ATM vault door(s). Remove the battery box cover by pulling the front portion away from the vault door. 2. The connector is easily removed by unsnapping it from the two (2) terminal on the top of the battery. 3. Remove the old battery. Install/connect a new 9-volt alkaline battery. 4. Push the battery and the leads completely up into the battery compartment. 5.
POWER AND COMMUNICATION 52
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE CONNECT POWER / COMMUNICATION CABLES * IMPORTANT NOTICE * This unit is shipped with an Uninterrupted Power Supply (UPS). For safety precautions, the backup battery installed in the UPS has been disconnected. Before applying power to the unit, follow the procedures below: Remove the battery cover by pushing the cover to the left (Figure 1). Connect the two (2) grey plugs (Figure 2). Reinstall the battery cover.
CONNECTING AC POWER AND ETHERNET CABLE POWER SUPPLY CORD SPECIFICATIONS POWER OUTLET ACCESSIBILITY Whether you are installing a new outlet, or plan to use an existing outlet to supply power to the ATM, make sure the following requirements are met: For European applications, the power supply cord must conform to the following specifications: 1. The outlet is located near the cabinet. 1. Two-conductor with physical earth ground. 2. The outlet is easily accessible. 2. 3.
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE THIS PAGE INTENTIONALLY LEFT BLANK 55
ENVELOPE SUPPLY UNIT 56
FT7000XP - SITE PREPARATION AND INSTALLATION GUIDE TESTING /ADJUSTING FOR ENVELOPE THICKNESS The optional Envelope Depository Unit (EDU) contains an Envelope Transport Mechanism, Shutter Assembly, and an Envelope Deposit Bin (secure). The Envelope Supply Unit holds approximately 200 envelopes. When loading envelopes, alternate every 50-100 with the flaps UP. For example, load 50 with flaps up facing Left, then next 50 with flaps facing Right.
ENVELOPE SUPPLY UNIT ADJUSTING THE ENVELOPE THICKNESS With a phillips screwdriver, loosen the screw shown and slide the plate back. Rotate the cam shown clockwise one (1) position if the envelope was double-feeding. If the envelope was not feeding, rotate the cam one (1) position counterclockwise. Slide the plate back and secure screw. Perform the DISPENSE AND RETRACT TEST again, minimum five (5) times.
FT7000XP - ALARM PANEL DIAGRAM 59
