Model RL5000 (X2) QUICK REFERENCE GUIDE THIS AREA FOR SERVICE PROVIDER CONTACT INFORMATION: TDN 07100-00092B Jan 29 2009
MANAGEMENT FUNCTIONS - ACCESS INSTRUCTIONS 1. AT ATM WELCOME SCREEN, PRESS AND HOLD DOWN THE KEY (LOWER - RIGHT CORNER OF KEYPAD ), PRESS <1> KEY , THEN RE LEASE BOTH KEYS . THE P ASSWORD ACCESS PROMPT IS DISPLAYED. 2. ENTER PASSWORD AND SELECT . THE MANAGEMENT FUNCTIONS MAIN MENU IS DISPLAYED. RESTART / SHUTDOWN TERMINAL FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SE- LECT SYSTEM PARAMETERS. RESTART TERMINAL: THIS FUNCTION REBOOTS THE TERMINAL.
DIAGNOSTICS FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SELECT DIAGNOSTICS > DISPENSER. PURGE: THIS INSTRUCTS THE DISPENSER TO REMOVE ANY NOTES (JAMS) IN FEED PATH. TEST DISPENSE: THIS INSTRUCTS THE DISPENSER TO DISPENSE MINIMUM ONE NOTE FROM EACH INSTALLED CASSETTE INTO THE REJECT CASSETTE / AREA . SELECT DIAGNOSTICS > PRINTER. RESET / TEST PRINTER : THIS INSTRUCTS THE PRINTER TO RE-INI- TIALIZE AND PERFORM A TEST PRINTOUT.
CASSETTE CLOSE FUNCTIONS FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SELECT TERMINAL CLOSE FUNCTIONS. SELECT CASSETTE CLOSE. SELECT CASSETTE(S) TO CLOSE. A CHECK MARK (√ √ ) IDENPRESS . TIFIES WHICH CASSETTE(S) ARE SELECTED. AFTER CASSETTE(S) HAVE BEEN REINSERTED IN THE DISPENSER, . PRESS NOTE: IF AN NMD-50 DISPENSER IS INSTALLED, WAIT FOR THE LOCK ( THIS IS DONE AUTOMATICALLY ). PRESS IF APPLICABLE. CASSETTES TO PLACE SELECTED CASSETTE(S) IN SERVICE.
REPLENISH TDM CASSETTE (TDM-100, -150) NOTE: TDM-150 IS ON A SLIDING MOUNTING TRAY. TDM-100 IS ON A STATIONARY TRAY. STEP ACTION STEP ACTION 1 UNLOCK/OPEN DISPENSER SECURITY DOOR. (FOR TDM150) RELEASE THE SLIDE LOCKING LEVER AND EXTEND 4 REMOVE THE NOTE CASSETTE. UNLOCK AND MOVE PACKER PLATE TO REAR OF THE CASSETTE. LATCH IN PLACE WITH THE HOLD-BACK LATCH. 5 COUNT THE NUMBER OF BILLS THAT REMAIN IN THE CASSETTE, IF ANY. THE DISPENSER MOUNTING TRAY FULLY.
REPLENISH TDM CASSETTE(S) (TDM-200, -250) STEP 1 ACTION UNLOCK/OPEN DISPENSER SECURITY DOOR. RELEASE THE SLIDE LOCKING LEVER AND EXTEND THE DISPENSER ACTION STEP MOUNTING TRAY FULLY. 4 R EMOVE THE N O T E CASSETTE(S). UNLOCK AND MOVE PACKER PLATE TO REAR OF THE CASSETTE . LATCH IN PLACE WITH THE HOLD-BACK LATCH. 2 L OCATE THE S P R I N G - LOADED LOCKING PIN ON UNDERSIDE OF TRAY. PULL PIN DOWN AND ROTATE 180° RELEASE PIN TO LOCK IN PLACE. SWIVEL PLATFORM Note cassettes CLOCKWISE.
REPLENISH SDD CASSETTE STEP 1 ACTION UNLOCK/OPEN DISPENSER SECURITY DOOR. G RASP THE CASSETTE HANDLE AND REMOVE THE CASSETTE. ACTION STEP 4 LIFT THE REJECT TRAY. PUSH THE PACKER PLATE TO REAR OF CASSETTE AND 2 LATCH IN PLACE. CASSETTE MUST BE PRIMEDWITH THE CASSETTE KEY BEFORE INSERTING ON THE LOADING TRAY. INSERT KEY AND TURN CLOCKWISE TO SHOW GREEN INDICATOR IN WINDOW. 5 Green window COUNT THE NUMBER OF BILLS THAT REMAIN IN THE CASSETTE, IF ANY.
REPLENISH NMD-50 CASSETTE(S) STEP ACTION 1 UNLOCK/OPEN DISPENSER SECURITY DOOR. GRASP CASSETTE HANDLE WITH ONE HAND WHILE HOLDING MECHANISM WITH THE OTHER. PULL CASSETTE OUT SLIGHTLY, THEN PLACE ONE HAND UNDER - NEATH. SETTE. REMOVE CAS- ACTION STEP 5 PLACE CURRENCY IN THE CASSE T T E AND MOVE PACKER PLATE AGAINST THE 2 NOTES. PRESS THE GREEN RELEASE BUTTON AND LIFT THE LID. FLIP THE LID BACK FULLY LETTING IT REST ON A FLAT SURFACE. 6 EXTEND THE “PAWLS” ON PACKER PLATE FULLY .
REPLENISH RECEIPT PAPER NOTE: THIS PROCEDURE REQUIRES TERMINAL IS POWERED UP. STEP 1 ACTION STEP OPEN CONTROL PANEL. IF PAPER REMAINS ON 4 ROLL , CUT OR TEAR PAPER BETWEEN ROLL AND INSTALL NEW PA- PER ROLL/ SPINDLE IN BRACKET. PRINTER . R EMOVE ACTION PAPER SPENT FROM PAPER ROLL AND ROLL! SPINDLE FORM PA- FEEDS TOP OF PER BRACKET . 5 2 PULL RELEASE FEED END OF PAPER INTO PRINTER TAKE-UP SLOT. PAPER FEEDS OVER THE BAR! PRINTER WILL AUTOMATICALLY GRIP AND PULL PAPER INTO FEED PATH.
COMBINATION LOCKS I NTRODUCTION THE SECURITY CABINET CAN BE SECURED USING AN ELECTRONIC COMBINATION LOCK. THESE PAGES COVER HOW TO OPERATE THE COMBINATION OF EITHER ELECTRONIC LOCK OFFERED. OPERATING THE ELECTRONIC LOCK THE ELECTRONIC LOCK COMBINATION CONSISTS OF SIX DIGITS. UPON ARRIVAL, THE COMBINATION OF THE LOCK SHOULD ALREADY BE PRESET TO 1-2-3-4-5-6. ENTERING THE COMBINATION 1. ENTER THE PRESET COMBINATION AND CHECK FOR PROPER OPERATION. AFTER EACH KEYPRESS, THE LOCK WILL BEEP.
TO CHANGE THE COMBINATION: 1. POWER LOCK - EC TURN THE DIAL TO THE LEFT (CCW) UNTIL “EC” (ENTER COMBINATION) IS DISPLAYED. 2. EC - ENTER SHELVED MODE COMBINATION - OPR ENTER THE CURRENT COMBINATION (EITHER 50-25-50 OR A CHANGED COMBINATION) BY SEQUENTIALLY PRESSING THOSE DIGITS ON THE LOCK KEYPAD. THE NUMBERS WILL BE DISPLAYED ON THE LCD AS THEY ARE ENTERED. 3. OPR - RETRACT BOLT TURN THE DIAL TO THE RIGHT (CW) TO RETRACT THE BOLT 4. OPEN DOOR 5.
COMMON ERROR CODES ERROR CODE MEANING 33 101 RECOMMENDATIONS 1. REMOVE AND OPEN CASSETTE(S). IF THERE IS CURRENCY IN CASSETTE, GO 2. IF NOT, LOAD CURRENCY AND PROCEED TO STEP 3. 2. IS CURRENCY OF GOOD QUALITY? IF YES, GO TO STEP 4. IF NOT, OBTAIN PROCEED TO STEP 4. 3. SHUFFLE CURRENCY AND REPACK CASSETTE. 4. RE-INSERT CASSETTE USING REPLENISHING CASSETTE PROCEDURES. TO STEP FEED FAILURE 306 QUALITY CURRENCY. 5. PERFORM A TEST DISPENSE (DIAGNOSTICS>DISPENSER>TEST DISPENSE).
