Attention Note: Please make sure the voltage is consistent with the local voltage before printing.If not, please adjust it (110V220V) Please check if the all the items are included in the packing list before installing the printer . If you have any questions, please contact customer service. Please use the machine in a ventilated, dry, clean and flat environment The machine contains high speed moving parts and high temperature parts.
Directory 1. Machine parameters ………………………… 2 2. Packing list ………………………………… 3 3. Machine details ……………………………… 4 4. Installation ………………………………… 5 5. Wiring connection …………………………… 6 6. Structure debug ……………………………… 7 7. Operation & Print ………………………… 8 8. Failure cause analysis ………………………14 Service email :Support@tronxy.
1. Machine parameters Print parameters: Print size : 255*255*260mm Print accuracy : 0.1-0.3mm Print principle : FDM(fused deposition molding) Nozzle size : 0.4mm Nozzle quantity : 1 Print speed : 20-100mm/s(advise 60mm/s) Position accuracy : X/Y -0.00625mm,Z – 0.00125mm Filaments support : PLA、ABS Temp parameters: Print environment : 8-40℃ Nozzle temp 275℃(MAX) : Power supply: AC 110/220V 50/60Hz DC 24V/360W Software: Slicer : Tronxy、Cura、Simplify3D Input format : .stl、.
2. Packing list XY-2 PRO Upper bracket Base Filament bracket Installation Manual HM5*50 4PCS Tools Shovel Power line USB cable Stickers Reader(with SD card) Filament 0.25KG Print head Clips(Color random) Quick connection M6 Ties Notes :Please check if all the items are included before installing the printer. If you have any questions , please contact the customer service.
3.
4. Installation Note: Please make sure the voltage is consistent with the local voltage before printing . If not, please adjust it (110V220V) Loosen the screws with the socket wrench and remove the touch screen from the beam. Remove the screws and nuts. Pass the removed screw through the touch acreen bracket and carry the ship nut. Lock the ship nut with socket wrench and fix the touch screen on the front beam profile of the base.
5. Wiring connection Switch board Switch line Z motor line Z motor line Switch board 6 Power 110v-220v switch Switch line installation method: Remove the buckle, and put it on the notch side of the quasi-adapter plate on the raised side of the adapter, and insert it firmly until the buckle bounces back.
6. Structure debug If the machine structure is loose during transportation, it can be solved by adjusting the eccentric nut.As shown in the figure below (eccentric nut in red circle), turn the nut with a wrench to adjust the tightness of the pulley (the pulley should not be adjusted too tight to avoid smooth operation). Left slicer Left slicer Right slicer Print Head Print Head Right slicer HeatBed Wrench Hot Bed If the structure is loose in other places, you can tighten the screws directly.
7.
Manual leveling: Click the four points of ABCD (see the picture ), the print head will move to the corresponding position, and then adjust the leveling nut M, to ensure the space between the nozzle and the platform is a piece of A4 paper. After adjusting the four points in turn, it needs to be verified again. If the interval is appropriate, the leveling is completed.
Load and unload filaments: Click 23/0 23/199 After waiting for temperature up to 180 ℃, filament go through from the filament detection, extruder and feed pipe to the nozzle until the filaments are squeezed , as the following picture shows : Feed pipe Straighten Filament Extrusion Filament run out detection Print test: Click →“TEST FILE”→ ,Start printing If the filaments cannot stick on the first layer or the nozzle hits the hotbed crazy when printing, then the distance of the nozzle and the hotbe
1. Installation Find out slice software in SD card“TronxyInstall.exe ”click twice , Then follow these steps to complete the installation.
2. How to use slice software ① Type setting: follow the steps below to complete the setting.
② Parameter setting:(The following figure gives the reference value, according to their own needs can be modified) Some parameters are set for reference: Layer thickness Print temp Heatbed temp Print speed Support 0.1-0.
8. Failure cause analysis 1. Machine cannot start 1)Check the power line and other wires are connected well or not . 2)Check whether the supply voltage suits the local standard. 3)Check whether the screen or power supply is damaged and replace it in time. 4)Check if the wires are damaged or broken. 5)Check whether the power fuse is burnt out. 2. The contents of the SD card cannot be read 1)Check the card reader if it is good. 2)If the computer can’t read the SD card , please format it and try again.
4. If the first layer upwarp 1)Check if the hot bed has been leveled well. 2)Check the surface of the hot bed for dirt. 3)Check whether the distance between the nozzle and the platform is too high, resulting in insufficient adhesive force. 4)Check the hot bed for adequate temperature. 5)Check the first layer of the slicing software to see if it is printing too fast. 5. The model is not easy to take off 1)Try to heat the hot bed to 50-70 ℃ take off it by the shovel .
9. Model dislocation and fault 1)Nozzle feeding not smoothly, please clean the nozzle or replace the nozzle 2)Check that if the printing speed is too fast 3)The quality of filaments is poor, please replace with new filaments 10.
ONLY NEEDS 3 STEP TO FINISH THE REST INSTALLATION FILAMENT RUN-OUT DETECTION RESUME PRINT AFTER POWER-OFF AUTO LEVEL ALL METAL