2 piece conversion kit aq2pckt 2200 Stringtown Rd. Evansville, IN 47711 800 - 694 - 9494 • fax 812 - 467 - 1245 www.TrophyRidge.com Visit our youtube page for set up videos.
CONTENTS Contact Informa on _____________________________ 1 Table of contents _____________________________ 2 Parts and hardware list _____________________________ 3 Disassembly of 1-piece quiver _____________________________ 4-5 Hood assembly for 2-piece quiver _____________________________ 6-7 Bo om assembly for 2-piece quiver _____________________________ 8 Moun ng 2-piece quiver to bow _____________________________ 9-10 Warranty _____________________________ 11 Contact Informa on ________
PARTS LIST - 2-PIECE QUIVER CONVERSION KIT P1 P4 P2 P3 Rod - 6” P1 QTY. 2 Rod - 4” P2 QTY. 2 Rod - 2” P3 QTY. 2 Bracket P4 QTY. 1 P6 P5 P8 H1 H2 Matthews Post Adapter P6 QTY. 1 P7 Triangle Post P5 QTY. 1 Hoyt Post Adapter P7 QTY. 1 H4 Cap Head Screw H4 QTY. 2 Cup P8 QTY. 2 H5 1/4-20 Post Screw H5 QTY. 1 -3- 10-24 Screw H1 QTY. 4 #10 Washer H2 QTY. 2 H6 Triangle Post Washer H6 QTY.
TOOLS NEEDED DISASSEMBLY OF 1-PIECE QUIVER The following steps describe how to disassemble your 1-piece quiver. You’ll convert it into a 2-piece quiver using the conversion kit in later steps. Step 1& 2 Step 3 DETAIL A 8/32” Screw 3/32” Allen Key Cap NOTE: Top Cap may look different depending on the model you have.
TOOLS NEEDED DISASSEMBLY OF 1-PIECE QUIVER -Cont. Step 4 1X Step 5 1X Allen Key- 3/32” for 8-32 screws (Not Included) Allen Key- 1/8” for 10-24 screws (Not Included) STEP 4 DETAIL D With a 1/8” Allen Key, loosen the 10-24 screws that are in the main adjustment bracket. Lift the rubber cover to access the screws, then loosen them enough to slide the bracket off the rods. See Detail D.
TOOLS NEEDED HOOD ASSEMBLY FOR THE 2-PIECE QUIVER The following steps describe how to assemble the hood section for the two piece quiver. Step 3 Allen Key- 3/32” for 8-32 screws 1X (Not Included) Step 1& 2 1X Allen Key- 1/8” for 10-24 screws (Not Included) NOTE Use the parts and hardware from the 1piece quiver for steps 1-3 but switch out the rods.
TOOLS NEEDED HOOD ASSEMBLY FOR THE 2-PIECE QUIVER The following steps describe how to assemble the two piece quiver using the conversion kit. Steps 4-6 1X 1X Allen Key- 3/32” for 8-32 screws (Not Included) Allen Key- 1/8” for 10-24 screws (Not Included) STEP 4 DETAIL D Locate the top gripper from the 1-piece quiver and take out the attached rubber grommets by squeezing them on one end and then pushing them down through the hole and out. See Detail B.
TOOLS NEEDED BOTTOM ASSEMBLY FOR THE 2-PIECE QUIVER The following steps describe how to assemble the bottom section for the two piece quiver. Steps 1-3 1X 1X DETAIL A H1 Allen Key- 9/64” for cap head screws (Not Included) Allen Key- 1/8” for 10-24 screws (Not Included) STEP 1 P4 Locate the two 2-inch rods (P3) or 4-inch rods (P2) and the bracket (P4) in the conversion kit. Insert two 10-24 screws (H1) from the kit and tighten with the 1/8” Allen Key until secure. See Detail A.
TOOLS NEEDED ATTACHING 2-PIECE QUIVER TO THE BOW RISER Step 1 Allen Key- 5/32” for 1/4-20 screws 1X FIGURE 1 (Not Included) NOTE Two posts are required for the 2-piece quiver, one will come from your 1-piece quiver and the second is included in the conversion kit. NOTE Attach both posts (P5) on the riser. The conversion kit includes a Hoyt post adapter and a Matthews adapter. Step 2 STEP 1 Attach the hood assembly post to the top riser hole. See Figure 1 & Detail A.
ATTACHING 2-PIECE QUIVER TO THE BOW RISER Step 3 TOOLS NEEDED Allen Key- 9/64” for cap head screws 1X (Not Included) 1X FIGURE 2 Allen Key- 1/8” for 10-24 screws (Not Included) NOTE Slide on the quiver hood assembly and lower assembly on the posts (P5) on the riser and tighten cap head screws. See Details C&D. NOTE After Steps 1-4 are complete tighten main adjustment bracket in the desired location on the rods. Lift the rubber cover to access the 10-24 screws. See Detail C.
T R O P H Y R I D G E WA R R A N T Y Trophy Ridge™ provides a Limited Lifetime Warranty on its products. All products are covered against breakage due to defects in materials, and workmanship from the date of purchase. Abuse or alteration of the product voids the warranty. In the event of breakage due to defects in materials or workmanship the liability of Trophy Ridge shall be limited to the lesser of the cost of repairing, or replacing the broken part.
Key Contact data Dealer 800 Number: 800-694-9494 Dealer Fax Number: 812-467-1245 Web: www.TrophyRidge.
