Installation Guide

ManualsBrandsTroposAir ManualsKitchenMustang 18 in. Oscillating Indoor/Outdoor Pure White Ceiling Fan

WARNING : Read and follow these instructions carefully and be mindful of all warnings shown throughout.

3MT18-1M

4.5 KGS.

9.9 LBS.

Net weight

Mustang

Toll Free: 1-855-676-7247

Owner’s Manual

This instruction contains 7 pages:

Page 1: Foreword

Page 2: Unpack and inspect parts contained

Page 3: Notes before installation

Page 4: Hanging system installation

Page 5: Wire connection

Page 6: Hanging base and Canopy installation

Page 7: Set up motor position, Blade installation and Remote

Summary of content (8 pages)

PAGE 1
Owner’s Manual Mustang 3MT18-1M This instruction contains 7 pages: Page 1: Foreword Page 2: Unpack and inspect parts contained Page 3: Notes before installation Page 4: Hanging system installation Page 5: Wire connection Page 6: Hanging base and Canopy installation Page 7: Set up motor position, Blade installation and Remote Net weight UL R 4.5 KGS. 9.9 LBS. Toll Free: 1-855-676-7247 WARNING : Read and follow these instructions carefully and be mindful of all warnings shown throughout.
PAGE 2
READ AND SAVE THESE INSTRUCTIONS WARNING : TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS, PLEASE OBSERVE THE FOLLOWING : 1]. To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly before beginning. 2]. To avoid possible electric shock, be sure electricity is TURNED OFF at the main power box before wiring. All electrical connections must be made in accordance with local codes, ordinances and/or the National Electric Code.
PAGE 3
Unpack and inspect fan carefully to be certain all contents are included.
PAGE 4
NOTES BEFORE INSTALLATION ai 90 o 55 o 55 o 3 adjustable motor positions (0/45/90 degree) 4 m 5d ax eg im re um e t ef ilt p fic o ie sit nc io y ng 110 degree oscillation (from center line: 55 degree left / 55 degree right) ns Note 1: This is an oscillating ceiling fan with features of 110 degree oscillation controlled by remote and 3 vertical positions (0/45/90 degree) manual tilt.
PAGE 5
WARNING: Fan should be at least 7 feet from the floor Note 1: Note 2: Turn off power at breaker box to avoid possible electrical shock. Use metal outlet box suitable for fan support. Outlet box must support 35 lbs min. Note 3: CAUTION: Oscillating device located at hanging base is fragile, do not damage or bend oscillating parts (cam/arm/motor) during installation Hanging Base OFF OFF OFF motor arm cam 1.
PAGE 6
2. WIRE CONNECTION 2A. Attaching safety cable to ceiling joist Use wood screw, spring washer, and flat washer from hardware bag. Pass wood screw through closed loop of safety cable. Secure wood screw to ceiling joist through any available slot on mounting plate. Make sure safety cable has been tightened securely. CAUTION: THE WOOD SCREW AND ITS SUPPORT MUST BE ABLE TO FULLY SUPPORT THE WEIGHT OF AT LEAST 100 LBS.
PAGE 7
3. HANGING BASE AND CANOPY INSTALLATION 3A. Carefully lift the fan assembly away from the hook on mounting plate. 1 Align direction marks on mounting plate with direction marks on hanging base. (see fig.1) 2 Push up hanging base until 2 set screws pre-installed on mounting plate are engaged with L type slots on hanging base. (see fig.1) 3 Slightly rotate hanging base until two screw heads are in L type slots. (see fig.
PAGE 8
4. SET UP MOTOR POSITION NOTE: Fan motor is at 0 degree when taken out from the carton, no need to change motor angle if intend to use the fan at 0 degree. There is one indicating line on downrod yoke and three on motor yoke for aligning 0/45/90 degree motor position (see fig. 1) 4A. Remove set screw and spring washer from motor yoke. (see fig. 2) 4B. Adjust motor angle by aligning one out of three indicating lines (0/45/90) on motor yoke with indicating line on downrod yoke .(see fig. 2) 4C.