TVE 40 T EN TRT-BA-TVE40T-TC-002-EN OPERATING MANUAL TOWER FAN
You can download the current version of the operating manual and the EU declaration of conformity via the following link: Table of contents Notes regarding the operating manual................................. 1 TVE 40 T Safety ..................................................................................... 1 Information about the device................................................ 3 Transport and storage........................................................... 3 Assembly and start-up..........
• • • • • • • • • • • • • Ensure that all electric cables outside of the device are protected from damage (e.g. caused by animals). Never use the device if electric cables or the power connection are damaged! The electrical connection must correspond to the specifications in chapter Technical data. Insert the mains plug into a properly secured mains socket. Observe the technical data when selecting extensions to the power cable. Completely unroll the extension cable. Avoid electrical overload.
Transport and storage Information about the device Note If you store or transport the device improperly, the device may be damaged. Note the information regarding transport and storage of the device. Device description The tower fan TVE 40 T is suitable for indoor air circulation.
Connecting the fan body and foot 1. Connect the assembled foot (3) with the fan body (2). 2. Screw the three connection screws (7) into the provided holes (8) at the bottom side of the fan body. Assembly and start-up Scope of delivery • • • 1 x Device TVE 40 T 1 x Remote control (without batteries) 1 x Manual Unpacking the device 1. Open the cardboard box and take the device out. 2. Completely remove the packaging. 3. Fully unwind the power cable.
Inserting batteries into the remote control Remove the battery cover (5) above the remote control's battery compartment and insert two AAA batteries (1.5 V). No.
Normal operation In normal operation mode the fan keeps running at the desired fan stage. The fan stage can be set from 1 to 6 in this operating mode and is shown on the segment display (13). Please proceed as follows to set the fan stage in normal operation mode: 1. Press the MODE button (12) until the = normal operation LED lights up among the operating mode LEDs (15). ð The device runs in normal operation mode. 2. Press the SPEED/TIMER button (9).
Automatic switch-off ü The device is switched on. 1. Press the TIMER button (17) to activate the timer. ð The Timer LED (16) flashes for approx. 5 s. 2. Press the SPEED/TIMER button (9) to select the desired number of hours until automatic switch-off. ð The segment display (13) indicates the number of hours until automatic switch-off. 3. Wait for 5 seconds to confirm the setting. ð The timer LED (16) is illuminated. The segment display (13) indicates the current fan stage and operating mode again.
Errors and faults Maintenance The device has been checked for proper functioning several times during production. If malfunctions occur nonetheless, check the device according to the following list. The device does not start: • Check the power connection. • Check the power cable and mains plug for damages. • Check the on-site fusing. • Check whether the overheating protection has tripped, see chapter Safety. • Wait for 10 minutes before restarting the device.
2. Clean the fan body's housing cover with a soft, damp and lint-free cloth. Ensure that no moisture enters the housing. Protect electrical components from moisture. Do not use any aggressive cleaning agents such as cleaning sprays, solvents, alcohol-based or abrasive cleaners to dampen the cloth. 3. Allow the housing cover to dry completely. 4. Reattach the cover at the rear of the fan body and tighten in the screw (20).
Disposal The icon with the crossed-out waste bin on waste electrical or electronic equipment stipulates that this equipment must not be disposed of with the household waste at the end of its life. You will find collection points for free return of waste electrical and electronic equipment in your vicinity. The addresses can be obtained from your municipality or local administration. For further return options provided by us please refer to our website www.trotec24.com.
Trotec GmbH & Co. KG Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.
