Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty OPERATOR’S MANUAL Pivot S WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 Printed In USA Form No.
1 To The Owner Thank You Thank you for purchasing a Troy-Bilt Zero-Turn Tractor. It was carefully engineered to provide excellent performance when properly operated and maintained. If applicable, the power testing information used to establish the power rating of the engine equipped on this machine can be found at www.opei.org or the engine manufacturer’s web site. Please read this entire manual prior to operating the equipment.
Important Safe Operation Practices 2 WARNING! This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol.
12. A missing or damaged discharge cover can cause blade contact or thrown object injuries. 13. Stop the blade(s) when crossing gravel drives, walks, or roads and while not cutting grass. 14. Watch for traffic when operating near or crossing roadways. This machine is not intended for use on any public roadway. 15. 4 Do not operate the machine while under the influence of alcohol or drugs.
Children 1. a. b. c. d. e. f. g. 2. Service Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. They do not understand the dangers. Never assume that children will remain where you last saw them. Safe Handling of Gasoline: 1. Keep children out of the mowing area and in watchful care of a responsible adult other than the operator. Be alert and turn machine off if a child enters the area.
3. 4. 5. Periodically check to make sure the blades come to complete stop within approximately (5) five seconds after operating the blade disengagement control. If the blades do not stop within the this time frame, your machine should be serviced professionally by an authorized dealer. Regularly check the safety interlock system for proper function, as described later in this manual.
Safety Symbols This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate. Symbol Description READ THE OPERATOR’S MANUAL(S) Read, understand, and follow all instructions in the manual(s) before attempting to assemble and operate DANGER — ROTATING BLADES Never carry passengers. Never carry children, even with the blades off.
SECTION 2 — SAFE OPERATION PRACTICES Figure 1 line Figure 2 (TOO STEEP) 15° Slope WARNING! Slopes are a major factor related to tip-over and roll-over accidents which can result in severe injury or death. Do not operate machine on slopes in excess of 15 degrees. All slopes require extra caution. Always mow across the face of slopes, never up and down slopes. To check the slope, proceed as follows: 1. Remove this page and fold along the dashed line. 2.
3 Assembly & Set-Up Contents of Crate • One Lawn Tractor • One Deck Wash Hose Coupler • One Engine Operator’s Manual • Two Hex Screws and Flat Washers • One Operator’s Manual Tractor Preparation Steering Wheel Column 1. The steering wheel column is tilted all the way back for shipping. Remove the upper crating material from the shipping pallet, and cut any bands or tie straps securing the tractor to the pallet. 2.
3. Place the flat washer and belleville washer over the steering wheel and secure with the hex screw. See Figure 3-3. 3. Steering Wheel Cover Rotate the seat into position and secure the seat into place with the previously removed shoulder screws and flange lock nuts. Be careful not to crimp or damage the wire harness while installing the seat. See Figure 3-4. NOTE: Be sure to push the excess wire from the wire harness into the seat box hole before continuing.
3. Install the discharge chute deflector using the carriage bolts, push nuts and flange lock nuts as shown in Figure 3-6. Setting the Front Gauge Wheels WARNING! Keep hands and feet away from the discharge opening of the cutting deck. NOTE: The deck wheels are an anti-scalp feature of the deck and are not designed to support the weight of the cutting deck. Move the tractor on a firm and level surface, preferably pavement, and proceed as follows: Figure 3-6 4.
Connecting the Battery Cables CALIFORNIA PROPOSITION 65 WARNING! Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling. CAUTION: When attaching battery cables, always connect the POSITIVE (Red) wire to its terminal first, followed by the NEGATIVE (Black) wire.
4 Controls & Features Brake Pedal Forward Drive Pedal Reverse Drive Pedal Parking Brake/Cruise Control Lever Steering Wheel Deck Lift Handle Deck Height Index Throttle/Choke Control LCD Service Minder & Hour Meter PTO Knob Ignition Switch Module Fuel Tank Cap Cup Holder Storage Tray Transmission Bypass Valves NOTE: References to LEFT, RIGHT, FRONT, and REAR indicate that position on the tractor when facing forward while seated in the operator’s seat.
Ignition Switch Module Throttle/Choke Control The throttle/choke control is located on the RH console to the left of the hour meter/indicator panel. When set in a given position, a uniform engine speed will be maintained. WARNING! Never leave a running machine unattended. Always disengage PTO, set parking brake, stop engine and remove key to prevent unintended starting. To start the engine, insert the key into the ignition switch and turn clockwise to the START position.
Park Brake/ Cruise Control Lock Pedal The park brake/cruise control lock pedal is located at the base of the steering column. It is used to engage the park brake when the tractor is at rest. Engaging the lever while the tractor is in motion allows the tractor to remain at a constant ground speed without applying pressure to the forward drive pedal. Refer to the Operation section of this manual for detailed instructions regarding the parking brake as well as the cruise control feature.
5 Operation General Safety Before Operating Your Tractor • RECEIVE INSTRUCTION — Entirely read this operator’s manual. Learn to operate this machine SAFELY. Do not risk INJURY or DEATH. Allow only those who have become competent in its usage to operate this tractor. • Before you operate the tractor, study this manual carefully to familiarize yourself with the operation of all the instruments and controls. It has been prepared to help you operate and maintain your tractor efficiently.
6. Starting the Engine WARNING! This tractor is equipped with a safety interlock system designed for the protection of the operator. Do not operate the tractor if any part of the system is malfunctioning. Periodically check the function of the interlock system for proper operation. WARNING! For personal safety, the operator must be sitting in the tractor seat when starting the engine.
6. Driving The Tractor WARNING! Avoid sudden starts, excessive speed and sudden stops. 1. Release the parking brake. Move the throttle/choke control lever into the FAST position. 2. To travel FORWARD, slowly press the forward drive pedal forward until the desired speed is achieved. See Figure 5-2.
3. Press the REVERSE PUSH BUTTON (Orange, Triangular Button) at the top, right corner of the key switch module. The red indicator light at the top, left corner of the key switch module will be ON while activated. See Figure 5-3. 4. Once activated (indicator light ON), the tractor can be driven in reverse with the cutting blades (PTO) engaged. 5. Always look down and behind before and while backing to make sure no children are around.
6 Maintenance & Adjustments Maintenance Schedule Before Each use Check & Clean Engine Cooling Fans for Debris Check Engine Oil Level Check Air Filter for Dirty, Loose or Damaged Parts After First 5 Hours 3 3 3 Every 10 Hours Every 25 Hours Every 50 Hours Every 100 Hours See Engine Manual 3 3 3 3 3 3 3 Clean Battery Terminals Grease All Lubrication Points Check Intake Screen/Clean as Needed Check Blades/Sharpen or Replace as Needed Check Tire Pressure Check/Clean Underside of Deck Grease Front Cast
NOTE: This Operator’s Manual covers several models. Tractor features may vary by model. Not all features in this manual are applicable to all tractor models and the tractor depicted may differ from yours. 5. After draining the oil, wipe any residual oil from the oil drain hose. Thread the square head plug into the drain hose fitting and fully tighten the plug. 6. Replace the oil filter, and refill the engine with new oil as instructed in the engine operator’s manual. 7.
4. Attach the hose coupler to the water port on the left of your deck surface. See Figure 6-2. Lubrication WARNING! Before lubricating, repairing, or inspecting, always disengage PTO, set parking brake, stop engine and remove key to prevent unintended starting. Front Wheels Each of the front wheel axles and rims is equipped with grease fittings. See Figure 6-3. Lubricate with a No. 2 multi-purpose grease applied with a grease gun after every 25 hours of tractor operation. Grease Fittings Figure 6-2 5.
Pivot Points & Linkage Leveling the Deck (Front-to-Rear) Lubricate all the pivot points on the drive system, parking brake and lift linkage at least once a season with light oil. Adjustments NOTE: Check the tractor’s tire pressure before performing any deck leveling adjustments. Refer to Tires on page 24 for information regarding tire pressure. Always level the deck side to side before front to rear. Deck The front of the deck should be between 1⁄4” and 3⁄8” lower than the rear of the deck.
Deck Wheels 4. NOTE: Use of a pressure washer or garden hose is not recommended to clean your riding mower. They may cause damage to electrical components, spindles, pulleys, bearings or the engine. The use of water will result in shortened life and reduce serviceability. WARNING!: Keep hands and feet away from the discharge opening of the cutting deck. NOTE: The deck wheels are an anti-scalp feature of the deck and are not designed to support the weight of the cutting deck.
7 Service NOTE: This Operator’s Manual covers several models. Tractor features may vary by model. Not all features in this manual are applicable to all tractor models and the tractor depicted may differ from yours. WARNING! Before performing any service, place the PTO switch in the “OFF” position, engage the parking brake lever, turn the ignition key to the “OFF” position and remove the key from the switch.
Releasing Belt Tension with the Idler Pulley Rolling the Belt off the PTO Pulley 1. 1. Using the deck lift handle, raise the deck to the position that provides the most horizontal run of the belt between the deck idler pulleys and the PTO pulley on the bottom of the engine. 2. Sitting behind the tractor facing forward, reach beneath the tractor to grasp the belt at the front of the PTO pulley.
6. Pull the cotter pin out of the front deck lift rod securing it to the deck. See Figure 7-6. Slide the deck lift rod out of the front hanger bracket. Deck Installation Install the deck on the tractor as follows: 1. Place the deck lift handle in the highest mowing position See Figure 7-3. 2. Slide the deck under the tractor on the right side of the tractor lining up the deck hanger brackets and the deck lift arms.. 3.
Replacing the Belt 1. 2. Remove the deck from beneath the tractor, (refer to Deck Removal). Loosen, but do not remove the hardware on the right and left idler pulley. Refer to Figure 7-8 for 46” decks and Figure 7-9 for 54” decks. 4. Install the new belt around the pulleys as shown and reinstall the belt covers. 5. Place the belt around the idler pulleys removed in step 3 with the “V” side facing in. Once in place, reinstall all the hardware and tighten the flange lock nut to secure the assembly. 6.
4. Tighten the blade nuts to 70-90 ft. lbs. 5. Reinstall the deck (refer to Deck Installation). Changing the Transmission Drive Belt Several components must be removed and special tools used in order to change the tractor’s transmission drive belt. See your authorized service dealer to have the transmission drive belt replaced. Tractor Creeping Creeping is the slight forward or backward movement of the mower when the throttle is on and the speed control levers are in the neutral position.
8 Troubleshooting Problem Excessive vibration Uneven cut Mower will not mulch grass (If Equipped w/Mulching Kit) 30 Cause Remedy 1. Cutting blade loose or unbalanced. 1. Tighten blade and spindle. 2. Damaged or bent cutting blade. 2. Replace blade. 1. Deck not leveled properly. 1. Perform side-to-side deck adjustment. 2. Dull blade. 2. Sharpen or replace blade. 3. Uneven tire pressure. 3. Check tire pressure in all four tires. 1. Engine speed too low. 1.
9 Replacement Parts Component Part Number and Description 954-04325 954-04329A Deck Belt, Pivot S46 Deck Belt, Pivot S54 954-04317A Drive Belt 942-04244A 942-05056A 2-in-1 Blade, Pivot S46 2-in-1 Blade, Pivot S54 918-05078A 918-06978 Spindle Assembly, Pivot S46 Spindle Assembly, Pivot S54 734-04155 Deck Wheel 925-1707D Battery 951-12179B Gas Cap 946-05145 Throttle/Choke Control Cable 625-05002 Ignition Key 31
Component Part Number and Description 631-05191A 631-05168A Chute Deflector, Pivot S46 Chute Deflector, Pivot S54 634-04293 634-04128 Wheel Assembly, Pivot S46 Wheel Assembly, Pivot S54 634-04711 Caster Wheel Assembly KH-12-050-01-S Oil Filter KH-12-132-02-S Spark Plug KH-25-050-22-S1 Fuel Filter KH-32-883-09-S1 Air Filter & Pre-Cleaner 32 SECTION 9 — REPLACEMENT PARTS
10 Attachments & Accessories Part No. Part 19B70020100 42” & 46” Bagger Kit 19A70043100 54” Bagger Kit 19A30006100 42” Mulch Kit 19A30005100 46” Mulch Kit 19A70042100 54” Mulch Kit 490-850-0005 Blade Removal Tool 490-850-0008 Oil Siphon 490-900-0045 Oil Filter Wrench 19A70025100 Hitch Kit 490-850-0005 Blade Removal Tool SPW-136 Spark Plug Wrench 490-325-0022 16 oz. Tire & Tube Sealant by Tire Science™ 490-325-0020 32 oz.
FEDERAL and/or CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS MTD Consumer Group Inc, the United States Environmental Protection Agency (EPA), and for those products certified for sale in the state of California, the California Air Resources Board (CARB) are pleased to explain the evaporative emission control system (ECS) warranty on your 2014-2015 small off-road equipment (outdoor equipment).
WARRANTED PARTS: The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such warranty coverage if MTD Consumer Group Inc demonstrates that the outdoor equipment has been abused, neglected, or improperly maintained, and that such abuse, neglect, or improper maintenance was the direct cause of the need for repair or replacement of the part.
MANUFACTURER’S LIMITED WARRANTY FOR The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise purchased and used in the United States and/or its territories and possessions, and by MTD Products Limited with respect to new merchandise purchased and used in Canada and/ or its territories and possessions (either entity respectively, “Troy-Bilt”). This warranty is in addition to any applicable emissions warranty provided with your product.
Medidas de seguridad • Configuración • Funcionamiento • Mantenimiento • Servicio • Solución de problemas • Garantía MANUAL DEL OPERADOR Pivot S ADVERTENCIA LEA Y OBSERVE TODAS LAS NORMAS E INSTRUCCIONES DE SEGURIDAD INCLUIDAS EN ESTE MANUAL ANTES DE PONER EN FUNCIONAMIENTO LA MÁQUINA. SI NO SIGUE ESTAS INSTRUCCIONES PUEDE PROVOCAR LESIONES PERSONALES. TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 Impreso en EE.UU. Formulario No.
1 Al propietario Gracias Gracias por comprar una Troy-Bilt de giro cero Tractor, ha sido cuidadosamente diseñada para brindar excelente rendimiento si se la opera y mantiene correctamente. Por favor lea todo este manual antes de hacer funcionar el equipo. El manual le indica cómo configurar, operar y mantener la máquina con seguridad y fácilmente.
2 Medidas importantes de seguridad ¡ADVERTENCIA! La presencia de este símbolo indica que se trata de instrucciones de seguridad importantes que se deben respetar para evitar poner en peligro su seguridad personal y/o material y la de otras personas. Lea y cumpla todas las instrucciones de este manual antes de intentar operar esta máquina. Si no respeta estas instrucciones puede causar lesiones personales. Cuando vea este símbolo.
4 12. Una cubierta de descarga que falte o esté dañada puede provocar lesiones por contacto con la cuchilla o por objetos arrojados. 13. Detenga la(s) cuchilla(s) cuando cruce caminos de gravilla, senderos o caminos y cuando no esté cortando el césped. 14. Vigile el tránsito vehicular cuando esté operando cerca de caminos o en cruces. Esta máquina no debe utilizarse en la vía pública. 15. No opere esta máquina estando bajo los efectos del alcohol o de drogas. 16.
Niños 1. Servicio Pueden ocurrir accidentes trágicos si el operador no está atento a la presencia de niños. Por lo general, los niños se sienten atraídos por este tipo de máquinas y su funcionamiento. No entienden los riesgos ni los peligros. Nunca asuma que los niños permanecerán en el mismo lugar donde los vio por última vez. a. b. c. d. e. f. g. 2. Manejo seguro de la gasolina: 1.
4. 5. 6. Controle periódicamente el funcionamiento del sistema de bloqueo de seguridad, tal como se describe más adelante en este manual. Si el sistema de bloqueo de seguridad no funciona correctamente, solicite el servicio de mantenimiento profesional al distribuidor autorizado. Inspeccione los pernos de montaje de la(s) cuchilla(s) y del motor a intervalos frecuentes, para verificar que estén bien ajustados.
Símbolos de seguridad En esta página se presentan y describen los símbolos de seguridad que pueden aparecer en este producto. Lea, entienda y cumpla todas las instrucciones incluidas en la máquina antes de intentar armarla y utilizarla. Symbol Description LEA LOS MANUALES DEL OPERADOR Lea, entienda y cumpla todas las instrucciones incluidas en los manuales antes de intentar armar la unidad y utilizarla. PELIGRO - GIRANDO HOJAS Nunca lleve pasajeros. Nunca transporte niños, aún con la cuchilla apagada.
8 SECCIÓN 2 — MEDIDAS IMPORTANTES DE SEGURIDAD Figura 1 tinua iscon nea d 15° lí 15° Pendiente ADVERTENCIA! Las pendientes son un factor importante relacionado con un vuelco y renovación de los accidentes que pueden provocar lesiones graves o la muerte. No utilice la máquina en pendientes de más de 15 grados. Todos pendientes requiere mayor precaución. Si no puede retroceder en la pendiente o si se siente inseguro en ella, no la recorte. Siempre corte el césped en toda la superficie de la cuesta.
3 Montaje y Configuración Contenido del cajón • Un tractor corta césped • Un acoplador de manguera para lavado de plataforma • Un Manual de operación del motor • Dos tornillo hexagonal y dos arandela plana • Un Manual del operador Preparación del tractor Columna del volante 1. Retire el material de embalaje superior del pálet de embarque, y corte cualquier banda o tira que fije el tractor al pálet. La columna de la dirección se inclina totalmente hacia atrás para el embarque. 2.
3. Coloque la arandela plana y la arandela belleville por encima del volante y ajústela con el tornillo hexagonal. Consulte la Figura 3-3. 3. Gire el asiento hasta la posición deseada y asegúrelo en su lugar con los tornillos de reborde y las tuercas de seguridad con brida que extrajo antes. Tenga cuidado de no doblar o dañar el cableado mientras instala el asiento. Vea la Figura 3-4.
Ajuste de las ruedas de calibración frontales ¡ADVERTENCIA! Mantenga las manos y los pies lejos de la abertura de descarga de la plataforma de corte. NOTA: Las ruedas de la plataforma son una característica anticuero cabelludo de la plataforma y no están diseñados para soportar el peso de la plataforma de corte. Mueva el tractor en una superficie firme y nivelada, preferentemente sobre el pavimento, y realice lo siguiente: 1.
Conexión de los cables de la batería ADVERTENCIA PROPOSICIÓN 65 DE CALIFORNIA Los bornes de la batería y los accesorios afines contienen plomo y compuestos de plomo, sustancias químicas que según lo establecido por el Estado de California causan cáncer y daños en el sistema reproductivo. Lávese las manos después de estar en contacto con estos componentes.
4 Controles y Características Pedal de freno Pedal de la transmisión marcha adelante Pedal de la transmisión hacia atrás Freno de mano / palanca de control de crucero Volante Manija de elevación de la plataforma Posicionamiento de la altura de la plataforma Control del acelerador/estrangulador Servicio LCD Minder y cronómetro Perilla de la toma de fuerza (PTO) Interruptor de encendido Tapón del depósito de combustible Portacubeta Bandeja de almacenamiento Válvulas de derivación de la transmisión NOTA:
Módulo del interruptor de encendido ¡ADVERTENCIA! Nunca deje la máquina en funcionamiento sin vigilancia. Siempre desconecte la potencia de arranque (PTO), coloque el freno de mano, apague el motor y retire la llave, para evitar que alguien encienda accidentalmente el motor. Para encender el motor, inserte la llave en el interruptor de encendido y gírela en el sentido de las agujas del reloj hacia la posición START (encendido).
Freno de mano/ CRUISE pedal de bloqueo del control de crucero CONTROL El freno de mano/pedal de bloqueo del control de crucero está ubicado en la base de la columna de la dirección. Se usa para poner el freno de mano cuando el tractor está inactivo. Cuando se engrana la palanca mientras el tractor está en movimiento permite que el tractor se mantenga a velocidad constante sin presionar el pedal de transmisión marcha adelante.
5 Funcionamiento 16 Seguridad general Antes de hacer funcionar el tractor • RECIBA LAS INSTRUCCIONES - Lea este manual del operador en su totalidad. Aprenda a usar esta máquina DE MANERA SEGURA. No se arriesgue a quedar expuesto a LESIONES o a la MUERTE. Solamente se debe permitir operar este tractor a quienes se hayan familiarizado a fondo con el uso del mismo.
6. Encendido del motor ¡ADVERTENCIA! Esta unidad está equipada con un sistema de bloqueo de seguridad para protección del operador. No opere el tractor si alguna parte del sistema funciona mal. Controle periódicamente el funcionamiento del sistema de bloqueo para verificar que funcionen adecuadamente. ¡ADVERTENCIA! Por razones de seguridad personal, el operador debe estar sentado en el asiento del tractor al arrancar el motor.
4. Gire la llave de encendido a la posición STOP quite la llave del interruptor de encendido. (parada) y 6. NOTA: Siempre quite la llave del interruptor de encendido para evitar el arranque accidental o la descarga de la batería si el equipo queda sin supervisión. Para conducir marcha atrás, verifique que el área de atrás esté despejada.
3. Presione el BOTÓN DE MARCHA ATRÁS (botón triangular de color naranja) en la esquina superior derecha del módulo del interruptor de llave. La luz indicadora roja en la esquina superior izquierda del módulo del interruptor de llave se mantiene encendida (ON) mientras esté activado. Vea la Figura 5-3. 4. Una vez activado (con la luz indicadora encendida), el tractor podrá operar en marcha atrás con las cuchillas de corte (PTO – potencia de arranque) enganchadas. 5.
6 Mantenimiento y Ajustes Programa de mantenimiento Antes de cada uso Revisar y Limpiar los ventiladores de enfriamiento del motor para Escombros Revise el nivel de aceite del motor Revise el filtro de aire para las piezas sucias, sueltas o dañadas Después de las primeras 5 horas 3 3 3 Cada 10 Horas Cada 25 Horas Cada 50 Horas Cada 100 Horas 3 3 3 3 3 3 3 Terminales de la batería limpios Engrasar todos los puntos de lubricación Compruebe Rejilla de admisión/limpie si es necesario Compruebe Cuchill
NOTA: Este manual de instrucciones abarca varios modelos. Características del tractor pueden variar según el modelo. No todas las funciones de este manual son aplicables a todos los modelos de tractor y el tractor se muestra puede diferir de la suya. ¡ADVERTENCIA! Antes de realizar cualquier operación de mantenimiento o reparaciones, desconecte la toma de fuerza, el freno de mano, apague el motor y la llave para evitar el encendido accidental de quitar.
2. Desactive el PTO (enganche de cuchilla), ponga el freno de estacionamiento y pare el motor. 3. Enrosque el acople de manguera (embalado con el Manual del Operador de su tractor) en el extremo de la manguera de su jardín. 4. Una el acople de la manguera al puerto de agua a la izquierda de la superficie de la cubierta. Vea la Figura 6-2.
Puntos de pivote y varillaje 5. Lubrique todos los puntos de pivote del sistema de accionamiento, freno de estacionamiento y el mecanismo de elevación de por lo menos una vez por temporada con aceite ligero. Ajustes La plataforma se encuentra correctamente nivelada cuando las dos mediciones desde las puntas de las cuchillas son iguales. Una vez alcanzado el ajuste necesario, vuelva a ajustar el perno de cabeza hexagonal de la ménsula frontal de suspensión izquierda de la plataforma.
Ruedas de plataforma 5. ¡ADVERTENCIA! Mantenga las manos y los pies lejos de la abertura de descarga de la plataforma de corte. NOTA: Las ruedas de la plataforma son una característica anticuero cabelludo de la plataforma y no están diseñados para soportar el peso de la plataforma de corte. Las ruedas de la plataforma debe ser de aproximadamente 1⁄4-1⁄2” del suelo, cuando la cubierta se encuentra en el valor de altura deseado.
7 Servicio NOTA: Este manual de operación cubre distintos modelos. Las características del tractor pueden variar según los modelos. No todas las características en este manual se aplican a todos los modelos de tractor y la máquina que se ilustra aquí puede diferir de la suya.
Liberar la tensión de la correa con la polea loca Al girar la correa de la polea del PTO 1. 1. Usando la manija de elevación de la cubierta, levante la plataforma a la posición que le ofrece mayor recorrido horizontal de la correa entre las poleas locas de la plataforma y la polea del PTO en la parte inferior del motor. 2. Sentado detrás del tractor, mirando hacia adelante, llegar debajo del tractor para agarrar la correa por la parte delantera de la polea del PTO.
6. Tire del pasador de chaveta hacia afuera de la varilla de elevación delantera de la plataforma que la sujeta a la plataforma. Consulte la Figura 7-6. Deslice la varilla de elevación de la plataforma fuera de la ménsula de suspensión frontal. Instalación de la plataforma Instale la plataforma sobre el tractor de la siguiente forma: 1. Ubique la manija de elevación de la plataforma en la posición de corte más elevada. Vea la Figura 7-3. 2.
Cambio de la correa 1. 2. Retire la plataforma desde abajo del tractor, (consulte Extracción de la plataforma). Afloje, pero no quite el hardware de la derecha y la izquierda de la polea loca. Consulte la Figura 7-9 para 46” cubiertas y la Figura 7-10 para 54“cubiertas. 5. Coloque la correa alrededor de las poleas tensoras que retiró en el paso 3 con la cara de “V”. Una vez en su lugar, volver a instalar todo el hardware y apriete la tuerca de seguridad con brida para fijar el conjunto. 6.
4. Para volver a instalar las cuchillas, realice el proceso anterior de forma inversa y apriete la tuerca a 70-40.82 kg. ft. NOTA: Agregue una pequeña cantidad de grasa multiuso a las roscas del perno para evitar la corrosión y la acción galvánica. 5. Reinstale la plataforma (consulte Instalación de la plataforma). ¡ADVERTENCIA! Nunca corte el césped con las cuchillas desafiladas. Si las cuchillas están dobladas es necesario cambiarlas. Las cuchillas de corte son filosas y pueden causar lesiones graves.
8 Solución de Problemas Problema Vibración excesiva Corte desigual La cortadora de césped no procesa los recortes como abono (si está equipada con kit de abono) Causa Solución 1. Cuchilla de corte floja o descentrada. 1. Apriete la cuchilla y el husillo. 2. Cuchilla dañada o doblada. 2. Reemplace la cuchilla. 1. La plataforma no está correctamente nivelada. 1. Haga un ajuste de la plataforma de lado a lado. 2. Cuchilla desafilada. 2. Afile o cambie la cuchilla. 3.
Notas 9 31
32 SECTION 9 — NOTAS
SECTION 9 — NOTAS 33
DECLARACIÓN FEDERAL y/o DE CALIFORNIA SOBRE GARANTÍAS EN EL CONTROL DE EMISIONES SUS DERECHOS Y OBLIGACIONES EN CUANTO A LA GARANTÍA MTD Consumer Group Inc, la Agencia de Protección Medioambiental de los Estados Unidos (EPA), y para aquellos productos certificados para su venta en el estado de California, el Departamento de los Recursos del Aire de California (CARB) se complacen en explicar la garantía que evaporativo sistema de control de emisiones (ECS) de su equipo (equipos de exteriores) de encendido po
8. Durante la totalidad del período de garantía del motor y equipo para todo terreno arriba mencionado, MTD Consumer Group Inc mantendrá un suministro de piezas bajo garantía suficiente para satisfacer la demanda esperada de tales piezas. 9. Cualquier pieza de reemplazo se podrá usar para el cumplimiento del mantenimiento o las reparaciones bajo garantía y se suministrarán sin cargo para el propietario. Dicho uso no reducirá las obligaciones de garantía de MTD Consumer Group Inc. 10.
GARANTÍA LIMITADA DEL FABRICANTE PARA La siguiente garantía limitada es otorgada por Troy-Bilt LLC con respecto a nuevos productos adquiridos y utilizados en Estados Unidos y/o sus territorios y posesiones, y por MTD Products Limited con respecto a nuevos productos adquiridos y utilizados en Canadá y/o sus territorios y posesiones (cualquiera de las dos entidades, respectivamente, “Troy-Bilt”). Esta garantía es adicional a la garantía de emisiones aplicables proporcionada con el producto.