Owner's Manual / Manual del Propietario Portable Generator 1 Generador Portatil Model 1 Modelo 0 19 19- 1 CAUTION % Before using this product, read this manual and follow all Safety Rules and Operating Instructions. PRECAUCION Antes de utilizar el producto, lea este manual y siga todas las Reglas de Seguridad e lnstrucciones de Uso.
Safety Rules U SAVE THESE I N S T R U C T I O N S TABLE OF C O N T E N T S Safety Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..2-4 Know Your Generator. ........................... .5 Assembly. .....................................6-7 Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 8 - 1 I Maintenance.................................... 12 Storage ........................................ 13 Troubleshooting.. ...............................
Section 1 : Safety Rules Turn generator OFF and let it cool at least 2 minutes before removing fuel cap. Loosen cap slowly t o relieve pressure in Fill o r drain fuel tank outdoors. D O N O T overfill tanl<.Allow space for fuel expansion. Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition sources. D O N O T light a cigarette o r smol
Section 1 : Safety Rules A WARNING I A CAUTION I D O NOT tamper with governed speed. Generator supplies correct rated frequency and voltage when running at governed speed. W H E N ADJUSTING OR MAKING REPAIRSTOYOUR GENERATOR Disconnect the spark plug wire from the spark plug and place the wire where it cannot contact spark plug. CAUTION W H E N TESTING FOR ENGINE SPARK Use approved spark plug tester. D O NOT check for spark with spark plug removed. I A WARNING I See "Don't Overload Generator".
1 \ I I I K N O W Y O U R GENERATOR Read this owner's manual and safety rules before operating y o u r generator. Compare this illustration with your generator t o familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.
Assembly ASSEMBLY Install Wheel Kit Your generator requires some assembly and is ready for use after it has been properly serviced with the recommended oil and fuel. NOTE: Wheel kit is.not intended for over-the-road use. You will need the following tools t o install these components: 112" o r 13mm wrench If you have any problems with the assembly of your generator, please call the generator helpline at 1-888-6 1 1-6708.
Section 3: Assemblv 7. Tip generator so that engine side is down. Add Fuel 8. Line up holes in support leg with holes in generator frame. 9. A t p c h support leg using t w o short (M8 x 16mm) cap screws and t w o locking hex nuts.Tighten with a 112" o'r 13mm socket and wrench. NOTE: -rhis gasoline engine is certified to operate on gasoline. Exhaust Emission Control System: EM (Engine Modifications). 10. O h support leg end of generator, slide handle onto center of top of frame. I I.
U S I N G T H E GENERATOR Generator Location' Generator Clearance System Ground The generator has a system ground that connects the generator frame components t o the ground terminals on the AC output receptacles.The system ground is connected t o the A C neutral wire (see "Equipment Description", earlier in this manual).
Section 4: Operation I 1 j OPERATING T H E GENERATOR NOTE: If engine starts but fails t o run, o r if unit shuts down during operation, make sure unit is on a level surface and check for proper oil level in crankcase.This unit may be equipped with a l o w oil protection device. See engine manual. electrical loads. Connect electrical loads in OFF position, then t u r n O N f o r Turn electrical loads OFF and disconnect from generator Allow equipment t o cool before touching.
Section 4: Operation L RECEPTACLES overload the generator. See "Don't Overload 1201240Volt AC, 30 Amp, Locking Receptacle Use a NEMA L14-30 plug with this receptacle. Connect a 4-wire cord set rated for 250VoltAC loads at 30 Amps (or greater) (Figure 5).You can use the same 4-wire cord if you plan t o run a I2OVolt load. Cord Set Use each receptacle t o operate 120Volt AC, single-phase, 60 H z electrical loads requiring up t o 2,400 watts (2.4 kW) at 20 Amps of current.
Section 4: Operation DON'T OVERLOAD GENERATOR 4. 5. 6. Repeat steps 4 and 5 for each additional load. supply -- Plug in and turn on the next load. Again, permit the generator t o stabilize. NEVER add more loads than the generator capacity.Take special care t o consider surge loads in generator capacity, as described above. You must make sure yourgenerator can enoughp rated (running) and surge (starting) watts for the items you will power at the same time. Follow these simple steps: I.
Maintenance NOTE: D O N O T use a garden hose t o clean generator. Water can enter engine fuel system and cause problems. In addition, if water enters generator through cooling air slots, some of the water will be retained in voids and cracks of the rotor and stator winding insulation-Water and dirt buildup on the generator internal windings will eventually 'decrease the insulation resistance of these windings. SPECIFICATIONS Starting Watts ........................ .8,550 watts Wattage ...................
Storage STORAGE + Engine Storage The generator should be started at least once every seven days and allowed t o run at least 30 minutes. If this cannot be done and you must store the unit for more than 30 days, use the following guidelines t o prepare it for storage. Generator Storage Clean the generator as outlined in "Generator Cleaning". Check that cooling air slots and openings on generator are open and unobstructed. See engine owner's manual for instructions.
Troubleshooting TROUBLESHOOTING Problem N o AC output is available, but engine is running. When loads are connected, engine runs good but bogs down. Cause Solution I. Circuit breaker is open. I. Reset circuit breaker. 2. Poor connection o r defective cord set. 2. Check and repair. 3. Connected device is bad. 3. Connect another device that is in good condition. 4. Fault in generator. 4. Contact Authorized Service Facility. I. Short circuit in a connected load. I.
TROY-BILTB O W N E R WARRANTY POLICY Effective November 1,2004 LIMITED WARRANTY "Troy-BiltB is a registered trademark of Troy-Bilt, LLC and is used under license t o B r i g s & Stratton Power Products. Brigs & Stratton Power Products will repair o r replace, free of charge, any part, o r parts of the equipment*" that are defective in material o r workmanship o r both.Transportation charges on parts submitted for repair o r replacement under this warranty must be borne by purchaser.
@ Operating & Maintenance lnstructions General Model Series noted on front cover are inclusive of the specific model number found on your engine. alnstrucciones de Mantenimiento & Operacib alnstructions d'utilisation et de maintenance , Los Modelos Serie Generales que aparecen registrados en la portada estan incluidos en el nlimero de modelo especifico encontrado en su motor. La serie de Modeles notee sur la page de garde comprend le numero de Modele spbcifique qui se trouve sur votre moteur.
I/ I Safety Precautionc a @ Precauciones de Seguridad 1 BEFORE OPERATING ENGINE Read entire Operating & Maintenance Instruc- ;FEE,,, * Briggs & Stratton does not necessarily know what equipment this engine will power. For that reason, you should carefully read and understand the operating instructionsfor the equipment on which your engine is placed.
Safety Precautionn The engine exhaust from this product contains chemicals known to the State of California to cause Drnmas xiones de Seguridad El gas de escape del motor que produce este product0 contiene quimicos conocidos para el Estado de California que ocasionan cancer, defectos de nacimiento, u otros d a i o s reproductivos. A CUANDO ANADA COMBUSTIBLE APAGUE el motor y deje que se enfrie al menos 2 minutos antes de remover la tapa de gasolina. Fill fuel tank outdoors or in well-ventilated area.
- . -, 7 - T*.--TmT,-, Precauciones de Segl Safety Precautio~ I ( I If there is natural or LP gas leakage in area, do not start engine. Do not use pressurized starting fluids because vapors are flammable. Start and run engine outdoors. Do not start or run engine in enclosed area, even if doors or windows are open. ( I I1 S'il y a une fuite de gaz nature1ou de GPLa proximite, I puertas o las ventanas When starting engine, pull cord slowly until resistance is felt, then pull rapidly.
-- W Safety Precautions Precauciones de Seguridad * l . - -- --,-- - - - - -- -- --"onsignes de sd~-~-:"' -? Laisser le silencieux, le cylindre du moteur et les ailettes refroidir avant de les toucher. Retirerlesdebriscombustibles accumulesautourdu silencieux et du cylindre. Remove accumulated combustibles from muffler area and cylinder area. Install and maintain in working order a spark arrester before using equipment on forest-covered, grass-covered, brush-covered unimproved land.
Armature air gap . . . . . . . . . . . 0.25 - 0.36 m . . . . . . . . . . . . . . . . . . . . . . . (0.010-0.014in.) Valve clearance: Valve springs installed and piston 114 in. (6 mm) past top dead center. Check when engine is cold. Intake . . . . . .0.1 0 - 0.1 5 mm (0.004 0.006 in.) Exhaust . . . . . 0.23 0.28 mm (0.009 0.011 in.) Bore . . . . . . . . . . . . . . . .68.26 mm (2.6875 in.) Stroke . . . . . . . . . . . . . . . 51.99 mm (2.0469 in.) - . . . . . 0.25 - 0.36 mm Entrefer Volant-Bobine . . . .
IIOI O n Off ONOFF Marche Arr& stop STOP Arrgt @ my 1x1 + 1 1 @ R e a d Owner's Manual Choke O n Fuel Shutoff LEI EL MANUALDEL PROPIETARIO ESTRANGULADOR ON CIERREDE COMBUSTIBLE Lire le manuel de I'utilisateur Starter Marche Fuel Robinet d'essence Choke Off ESTRANGULADOR Off COMBUSTIBLE Starter Arret Carburant e 4 oil ACEITE Huile v -dm Engine shipped from Briggs & Stratton without oil. Before startina enaine, fill with oil. Do not over-fill. nelo de aceite.
P . n r a r * r * a p : Adding 1 Checking oil level. ON LOW OIL FILL: Oil level should be at point of overflowing. ON LOW OIL FILL WITH DIPSTICK: Insert dipstick but DO NOT TIGHTEN. Remove and check oil level. PARA LLENADO DE ACEITE BAJO: El nivel de aceite debe qugdar en el punto de reboce. PARA LLENADO DE ACEITE BAJO CON VARILLA INDICADORA DE NlVEL DE ACEITE: lnserte la varilla de nivel de aceite per0 NO LA APRIETE. Remueva la varilla de nivel de aceite y compruebe el nivel de aceite.