Safe Operation Practices • Set-Up • Operation • Service • Troubleshooting Operator’s Manual Lawn Tractor Table of Contents Safe Operation Practices......................................... 2 Assembly & Set-Up................................................... 7 Controls & Operation..............................................11 Service......................................................................15 Troubleshooting..................................................... 20 Parts/Warranty............
Important Safe Operation Practices WARNING! This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol.
0. If situations occur which are not covered in this manual, use care and good judgment. Contact your customer service representative for assistance. 7. Slope Operation Slopes are a major factor related to loss of control and tip-over accidents which can result in severe injury or death. All slopes require extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it.
l. Never store the machine or fuel container inside where there is an open flame, spark or pilot light as on a water heater, space heater, furnace, clothes dryer or other gas appliances. m. 1. Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odorless, and deadly gas. 2. Before cleaning, repairing, or inspecting, make certain the blade(s) and all moving parts have stopped.
Safety Symbols This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate. Symbol Description READ THE OPERATOR’S MANUAL(S) Read, understand, and follow all instructions in the manual(s) before attempting to assemble and operate DANGER — ROTATING BLADES Never carry passengers. Never carry children, even with the blades off.
Section 2 — Important Safe Operation Practices Figure 1 line Figure 2 (TOO STEEP) 15° Slope WARNING! Slopes are a major factor related to tip-over and roll-over accidents which can result in severe injury or death. Do not operate machine on slopes in excess of 15 degrees. All slopes require extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it. Always mow up and down slopes, never across the face of slopes. To check the slope, proceed as follows: 1.
2 Assembly & Set-Up Thank You Thank you for purchasing this product. It was carefully engineered to provide excellent performance when properly operated and maintained. Please read this entire manual prior to operating the equipment. It instructs you how to safely and easily set up, operate and maintain your machine. Please be sure that you, and any other persons who will operate the machine, carefully follow the recommended safety practices at all times.
Tools Required • Shipping Brace Removal WARNING! Make sure the tractor’s engine is OFF, remove the ignition key, and set the parking brake before removing the shipping brace. Refer to the Controls & Operations section on page 8 for instructions on how to set the parking brake.
5. To adjust the position of the seat, remove the adjustment knob (a) on the bottom of the seat (b). Slide the seat (b) forward or backward as desired. Reinstall the adjustment knob (a). See Figure 2-6. Dash Shroud (If Equipped) There are two shroud types. One shroud for the 1/3/5/K/T-Style and one for the S-Style dash. 3. 4. Close the hood and align the dash shroud (a) to the hood (g) leaving a uniform gap between the hood (g) and the dash shroud (a).
filler neck to allow space for fuel expansion. See Figure 2-10. STOP STOP! Continue to Setting the Deck Gauge Wheels (If Equipped) on page 10. Attaching the Hood Scoop (If Equipped) On some tractors, a hood scoop may be included. If the hood scoop was not installed on the hood of your tractor at the factory, refer to the following steps to install the hood scoop: 1. Setting the Deck Gauge Wheels (If Equipped) Cut the cable ties securing the hood scoop to the tractor. 2.
3 Controls & Operation To set the parking brake: Fully depress the parking brake pedal. Move the parking brake lever all the way down and into the parking brake position (PARK BRAKE ON) and then release the brake pedal to allow the parking brake to engage. Hydrostatic Set-Up Ammeter † Throttle/Choke Control Lever Ignition Switch Module To release the parking brake: Depress the brake pedal and the parking brake lever will automatically move out of the parking brake position.
Shift Lever (If Equipped) Ignition Switch Module Deck Lift Lever Foot Control CVT & CVT The lawn tractor will have one of the following ignition switches. Refer to Figure 3-3 to identify which switch your machine utilizes and follow the applicable instructions for proper operation. The deck lift lever is located on the lawn tractor’s right fender. It is used to change the height of the cutting deck. To use, move the lever to the left, then place in the position best suited for your application.
To use the REVERSE CAUTION MODE: Setting the Cutting Height IMPORTANT: The operator MUST be seated in the lawn tractor seat. 1. Select the height position of the cutting deck by placing the deck lift lever in any of the five different cutting height notches on the right side of the fender. WARNING! Always look down and behind before and while traveling in reverse to avoid a back-over accident. 2.
CVT Foot Control CVT Engaging the Blades Engaging the PTO (blade engage) transfers power to the cutting deck. To engage the blades, proceed as follows: 1. Depress the clutch-brake pedal to release the parking brake and let the pedal up. 1. Depress the brake pedal to release the parking brake and let the pedal up. 2. Move the throttle lever into the FAST (rabbit) position. 2. Move the throttle lever into the FAST (rabbit) position. 3.
4 Service Maintenance Schedule Before Each use Every 10 Hours Every 25 Hours Every 100 Hours P P Clean Hood/Dash Louvers Clean Battery Terminals Clean Engine Cooling Fins P Lube Pedal Pivot Points 3. Open the protective cap on the end of the oil drain valve to expose the drain port. See inset of Figure 4-1. WARNING: Before performing any maintenance or repairs, disengage PTO, move shift lever into neutral position, set parking brake, stop engine and remove key to prevent unintended starting.
Engine Cleaning the Engine & Deck Lubricate the engine with motor oil as instructed in the Engine Operator’s Manual. Engine Pivot Points & Linkage Lubricate all the pivot points on the drive system, parking brake and deck lift linkage at least once a season with light oil. Rear Wheels The rear wheels should be removed from the axles once a season. Lubricate the axles and the rims with an all-purpose grease before re-installing them.
Charging Removing the Battery WARNING! Batteries emit an explosive gas while charging. Charge the battery in a well ventilated area and keep away from an open flame or pilot light as on a water heater, space heater, furnace, clothes dryer or other gas appliances. 3. To remove the battery, pull outward and then up on the battery hold-down bracket. See Figure 4-5. Locate the jam nut and lock nut on the front side of the stabilizer bracket.
Seat Adjustment 5. Refer to Attaching the Seat in page 8 for seat adjustment instructions. Parking Brake Adjustment WARNING! Never attempt to adjust the brakes while the engine is running. Always disengage PTO, move shift lever into neutral position, stop engine and remove key to prevent unintended starting. Looking at the cutting deck from the left side of the tractor, locate the bow-tie pin that secures the deck support rod on the rear left side of the deck. See Figure 4-9.
IMPORTANT: If the cutting edge of the blade has already been sharpened to within 1-5⁄8” from the edge, or if any metal separation is present, replace the blades with new ones. See Figure 4-13. 2. Remove the belt covers by removing the hex washer screws that fasten them to the deck. See Figure 4-14. Hex Washer Screws Spindle Pulley Belt Cover Belt Guard 1-5 /8 in Deck Idler Pulley ch ( min .
5 Troubleshooting Problem Engine fails to start Cause Remedy 1. PTO engaged. 1. Place PTO in disengaged (PTO OFF) position. See page 12. 2. Spark plug wire disconnected. 2. Connect wire to spark plug. See Engine Operator’s Manual. 3. Fuel tank empty, or stale fuel. 3. Fill tank with clean, fresh (less than 30 days old) gas. See page 9. 4. Choke not activated. 4. Place the throttle/choke control lever in CHOKE position. 5. Faulty spark plug. 5. Clean, adjust gap or replace plug.
Medidas de seguridad • Configuración • Funcionamiento • Servicio • Solución de problemas Manual del Operador Tractor cortacésped Índice Medidas de seguridad.................................................. 2 Montaje y Configuración............................................. 7 Controles y Funcionamiento.....................................11 Servicio.........................................................................15 Solución de Problemas...............................................
2 Importantes medidas de seguridad ¡ADVERTENCIA! Este símbolo indica instrucciones de seguridad importantes que, de no seguirse, podrían poner en peligro su seguridad personal y/o su propiedad o la de terceros. Lea y cumpla todas las instrucciones de este manual antes de intentar hacer funcionar esta máquina. Si no respeta estas instrucciones puede provocar lesiones personales.
30. Si se presentan situaciones que no están previstas en este manual, tenga cuidado y use el sentido común. Póngase en contacto con su representante de atención al cliente para obtener ayuda. 7. Funcionamiento en pendiente Las pendientes son uno de los principales factores asociados a los accidentes por pérdida de control y vuelcos que pueden producir lesiones graves o la muerte. Todas las pendientes exigen precaución adicional.
l. m. Nunca guarde la máquina o el recipiente de combustible en un espacio cerrado donde haya fuego, chispas o luz piloto, como por ejemplo de calentadores de agua, calefactores de ambientes, hornos, secadores de ropa u otros aparatos a gas. 8. 9. Deje que la máquina se enfríe por lo menos cinco minutos antes de guardarla. Servicio general 1. 2. 3. 4. 5. Nunca encienda el motor en espacios cerrados o en una zona con poca ventilación.
Símbolos de seguridad En esta página se presentan y describen los símbolos de seguridad que pueden aparecer en este producto. Lea, comprenda y siga todas las instrucciones incluidas en la máquina antes de intentar armarla y hacerla funcionar. Símbolo Descripción LEA LOS MANUALES DEL OPERADOR Lea, entienda y siga todas las instrucciones incluidas en los manuales antes de intentar armarla y hacerla funcionar. PELIGRO — CUCHILLAS GIRATORIASNunca lleve pasajeros.
6 Sección 2 — Importantes medidas de seguridad Figura 1 Línea 15° Slope ¡ADVERTENCIA! Las pendientes son uno de los principales factores asociados a los accidentes por tumbos y vuelcos que pueden producir lesiones graves o la muerte. No utilice la máquina en pendientes de más de 15°. Todas las pendientes exigen precaución adicional. Si no puede retroceder por la pendiente o si no se siente seguro, no realice ningún corte.
2 Montaje y Configuración Muchas gracias Gracias por comprar este producto. Ha sido cuidadosamente diseñado para brindar excelente rendimiento si se lo hace funcionar y se lo mantiene correctamente. Por favor lea todo este manual antes de hacer funcionar el equipo. El manual le indica cómo configurar, hacer funcionar y mantener la máquina de manera fácil y segura.
Herramientas necesarias • Extracción de la traba de seguridad ¡ADVERTENCIA! Compruebe que el motor del tractor cortacésped está APAGADO, retire la llave de encendido y ponga el freno de mano antes de sacar la traba de seguridad. Consulte la sección Controles y Funcionamiento en la página 28 para obtener instrucciones sobre cómo poner el freno de mano.
5. Para ajustar la posición del asiento, retire la perilla de ajuste (a) que está en la parte inferior del asiento (b). Deslice el asiento (b) hacia adelante o hacia atrás, según lo desee. Vuelva a colocar la perilla de ajuste (a). Consulte la Figura 2-20. Cubierta de instrumentos (si está equipado) Hay dos ipos de velo. Una cubierta para el / / T-Estilo 1/3/5 K y otro para el salpicadero S-Style. Continuar por debajo de 1/3/5 / K / T-Style, salte a la sección S-estilo para el tablero de estilo S. 3. 4.
Figura 2-24 3. Vuelva a colocar la tapa del combustible. IMPORTANTE: No llene en exceso el depósito de combustible. Llene el depósito no más de 1⁄2” por debajo de la base del cuello de llenado dejando espacio para la expansión del combustible. Consulte la Figura 2-24.
3 Controles y Funcionamiento Configuración Hidrostática Amperímetro † Palanca de control del acelerador/cebador Módulo del interruptor de contacto Para sacar el freno de mano: Presione el pedal de freno y la palanca del freno de mano automáticamente saldrá de la posición del freno de mano. Palanca del freno de mano /Control de velocidad † Pedal de freno †/Pedal de embrague-freno † Pedal de CVT y CVT Para poner el freno de mano: Presione totalmente el pedal del freno.
Palanca de cambios (si está equipada) Módulo del interruptor de contacto Palanca de elevación de la plataforma Pedal de CVT y CVT El tractor cortacésped tendrá uno de los siguientes interruptores de contacto. Consulte la Figura 3-3 para identificar qué interruptor utiliza su máquina y siga estas instrucciones para un funcionamiento adecuado. La palanca de elevación de la plataforma se encuentra sobre el guardabarros derecho del tractor cortacésped.
Para utilizar el MODO PRECAUCIÓN MARCHA ATRÁS: Ajuste de la altura de corte IMPORTANTE: El operador DEBE estar sentado en el asiento del tractor cortacésped. 1. Seleccione la altura de corte de la cubierta de corte colocando la palanca de elevación de la cubierta en cualquiera de las cinco muescas de altura de corte, en el lado derecho del guardabarros. ¡ADVERTENCIA! Siempre mire hacia abajo y hacia atrás antes de retroceder y mientras lo hace, para evitar accidentes por manejar marcha atrás. 2.
CVT Pedal de CVT Enganche de las cuchillas Al conectar la PTO (enganche de cuchillas) se suministra energía a la plataforma de corte. Para enganchar las cuchillas, haga lo siguiente: 1. Presione el pedal de embrague-freno para liberar el freno de mano y deje que suba el pedal. 1. Presione el pedal de freno para liberar el freno de mano y deje que suba el pedal. 2. Mueva la palanca del acelerador a la posición RÁPIDO (liebre). 2. Mueva la palanca del acelerador a la posición RÁPIDO (liebre). 3.
4 Servicio Programa de mantenimiento Antes de cada uso Cada 10 horas Cada 25 horas Limpie los bornes de la batería Limpie las aletas de refrigeración del motor P Lubrique los puntos de pivote del pedal 3. ADVERTENCIA: Antes de realizar tareas de mantenimiento o reparaciones, desconecte la potencia de arranque (PTO), mueva la palanca de cambios a la posición neutral, coloque el freno de mano, apague el motor y retire la llave, para evitar el enganch accidental del motor.
Motor Limpieza del motor y de la plataforma Lubrique el motor con aceite de motor como se indica en el Manual del Operador del Motor. Motor Puntos de pivote y varillaje Lubrique todos los puntos de pivote del sistema de impulsión, el freno de mano y el varillaje de elevación al menos una vez por temporada con aceite ligero. Ruedas traseras Las ruedas traseras se deben sacar de los ejes una vez por temporada. Lubrique bien los ejes y las llantas con una grasa multiusos antes de reinstalarlos.
Carga Extracción de la batería ¡ADVERTENCIA! Mientras cargan, las baterías emiten un gas que puede causar explosiones. Cargue la batería en un área bien ventilada y manténgala alejada de una llama expuesta o piloto, como los de los calentadores de agua, calefactores de ambiente, hornos, secadores de ropa y otros aparatos a gas. 3. Localice la contratuerca y la tuerca de seguridad que se encuentran en la parte delantera de la ménsula estabilizadora. Consulte la Figura 4-6. 4.
5. Una vez logrado el ajuste correcto, vuelva a ajustar el tornillo hexagonal de la ménsula de suspensión izquierda de la plataforma. 5. Ajuste del asiento Consulte las instrucciones de Instalación del asiento en la página 8. Ajuste del freno de mano Mirando la plataforma de corte desde el lado izquierdo del tractor, ubique el pasador de chaveta que sujeta la varilla de soporte de la plataforma del lado posterior izquierdo de la plataforma. Consulte la Figura 4-9.
IMPORTANTE: Si el borde cortante de la cuchilla ya ha sido afilado hasta 1-5⁄8” del borde, o si existe una separación de metal, reemplace las cuchillas por otras nuevas. Consulte la Figura 4-13. 2. Extraiga las cubiertas de la correa retirando los tornillos con arandela hexagonales que las sujetan a la plataforma. Consulte la Figura 4-14. Tornillos de arandela hexagonal Polea del husillo Protección de Cubierta de la la correa correa Polea loca de la plataforma 11- 5 -/ 5/88pu inlcgh. ((m mínin.) .
5 Solución de Problemas Problema El motor no arranca Causa 1. Potencia de arranque (PTO) conectada. 2. Se ha desconectado el cable de bujía. 3. El tanque de combustible está vacío o el combustible se ha echado a perder. 4. No se ha activado el cebador. 5. La bujía no funciona correctamente. 6. Fusible quemado 7. Motor ahogado. 8. No está colocado el freno de mano. 9. La palanca de control del regulador/cebador no está en la posición de arranque correcta. 10. Batería descargada.