vic. Chi bee MHZ-08eD O OVERBUILT Operator's Manual Yard Vacuum Chipper/Shredder/ Vacuum/Hose Model Numbers 24B-060F063 24C-060F063 IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest covered, brush-covered or grass-covered Sand unless the engine's exhaust system is equipped with a spark arrested meeting applicable local or state laws {if any}. i a spark arrested is used.
TABLE TEN Content important Oafs Operation Practices. Assembling Your Yard Vacuum Know Your Yard Vacuum Operating Your Yard Vacuum. Maintaining Your Yard Vacuum Troubleshooting Paris List DING MODE| R This Operator's Manual is an important part of your new Yard Vacuum. It will help you assemble, prepare and maintain the unit for best performance. Please read and understand what it says.
SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: This symbol points aut important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and folio all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may resulting personal injury. When you see this symbol heed its warning.
i. Never store the machine or fuel container inside where there is an open flame, spark, or pilot light (e.g. furnace, water heater, space heater, clothes dryer, etc.) j. To reduce a fire hazard, keep machine free of grass, leaves, or other debris build-up. Clean up oil or fuel spillage and remove any fuel soaked debris. k. Allow machine to cool at least § minutes before storing. OPERATION Do not put hands and feet near rotating parts or in the feeding chambers and discharge opening.
understand and follow the warnings and instructions in this manual and on the machine. fl WARNING YOUR RESPONSIBILITY: Restrict the use of this power machine 10 persons who read, NOTE: Not all safety labels may apply to your Yard Vacuum. DANGER + TO AVOID SERIOUS INJURY * READ OPERATOR'S MANUAL. « KEEP HANDS QUT OF INTERLARD DISCHARGE OPENWORK WHILE MACHINE S RUNNING. ROTATING SADES ARE INSIDE. « TURK ENTIRE OFF AND ALLOW IMPELLER TO COME TO COMPLETE STOP BEFORE REMOVING BAG.
Attaching The Handle Unfold the upper handle until it aligns with the lower handle. + Secure the two handles by tightening the wing noels (carriage bolts must be seated properly into the handle). See Figure 1 + Remove the hairpin clips from the handle brackets on the Yard Vacuum and remove the carriage bolts and wing nuts from the lower handle. See Figure 2. + Place the bottom holes in tower handle over pins on handle brackets and secure with hairpin clips.
Attaching The Blower Chute (it Equipped) NOTE: The blower chute is an optional feature on seem model yard vacuums. I is NOT standard equipment, if your unit is not equipped with a blower chute, contact Customer Support as instructed on page 2 for information regarding price and availability. Locking Satiety < Grasp bower chute with one hand and slide docking A Switch rod on mounting bracket with other hand toward engine. Use end of mounting bracken as leverage when sliding the locking rod. See Figure 5.
Chipper Chute Allow twigs and small branches up to 1 172" in diameter to be fed into the impeller for chipping. Blows Chute (if Equipped) When attached to unit the blower chute is used to blow or scatter yard waste such as leaves, pine neediest, or small twigs across yard. Nozzle Height Adjustment Lever Used to adjust the nozzle ground clearance ranging approximately 5/8" to 4 1/8”. Nozzle ‘Yard waste such as deaves or pine needles can be vacuumed up through the nozzle for shredding.
= Twist the two buttons on the back of the bag to unlock and empty contents. See Figure 7. « Hold bag handle and bag clip while emptying the contents. » Compress bag opening and fold inner flap over opening. < Fold outer flap over inner flap and insert buttons on the bag through metal cutlets. « Twist the buttons to lock bag.
Nozzle Height Adjustment The nozzle can be adjusted to any six positions, ranging from 5/8" to 4 1/8” ground clearance. The nozzle height has to be adjusted according (o the conditions. Move the height adjustment levers forward or backward to adjust the nozzle upwards or downwards. Make sure both levers are in the same position. See Figure 10.
OVERBUILT Complete the attached registration card and return today to receive these 3 important benefits: CONFIRM YOUR WARRANTY: Your prompt product registration confirms your right to the protection available under the terms and conditions of your Troy-Britt warranty. "% T PROTECT YOUR PRODUCT: We will keep the model number and date of purchase of your new Troy-Silt product on file to help you refer to this information when necessary.
Please do nat send products or other [ oae correspondence 1o Hie address below. CELLULARS: o148 STAMP HERE OTROV-BRYT PRODUCT REGISTRATION DEPARTMENT PO BOX 8566 DENVER CO 80201-8566 Habhthavshdlanliaboddodia dheabbadbiesbll + PLEASE FOOL AND SEAL WITH TAPE BEFORE MALIGN.
Maintenance Engine Refer 10 the separate engine manual for all engine maintenance instructions. « Check engine oil level before each use as instructed in the separate engine manual packed with your unit. Read and follow instructions carefully. « Clean air cleaner every 25 hours under normal conditions or once a season. Clean every few hours under extremely dusty conditions. To service the air cleaner, refer to the separate engine manual packed with your unit.
Lower Housing Screws Figure 14 + Remove lock nut that secures flair screen to the lower housing. The flail screen does not have to be removed. Refer to Figure 11. + Remove the hex bolt, lock washer, and flat washer that secure the impeller assembly to the crankshaft. See Figure 15. . W Upper . Housing Hipper Blade Imperf Assembly Hex Bolt Lock Washer Fiat Washer Flatt Bide BOTTOM VIEW Figure 15 * Apply lubricant to the threads of impeller removal toot and then thread the 100l into the crankshaft.
SECTION 6: TROUBLESHOOTING composition of discharged material changes. Problem Cause Remedy Engine fails to start 1. Spark plug wire disconnected. 1. Connect wire 1o spark pig. 2. Fief tank empty or stale fuel. 2. Fill tank with clean, fresh gasoline. 3. Throttle control lever not in correct | 3. Move throttle lever to FAST position. starting position. 4. Choke not in CHOKE position. (if 4. Move choke to CHOKE position. Equipped) 5. Engine (if equipped with primer} | 5. Prime engine. not primed properly. 8.
MANUFACTURER’S LIMITED WARRANTY FOR: PROVABILITY The limited warranty set forth below is given by Troy-Silt LLC with respect to new merchandise purchased and used in the United States, its possessions and territories. “Troy-Silt" warrants this product against defects in material and workmanship for a period of two (2) years commencing on the date of original purchase and will, at its option, repair or replace, free of charge, any part found to be defective in materials or workmanship.
