Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty Model 45700 BY MOJACK DISTRIBUTORS, LLC WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. Ver.
Troy-Bilt TB500ML Introduction This manual contains assembly, parts, operating, maintenance, adjustment and safety instructions for your lift. BEFORE USING YOUR LIFT, CAREFULLY READ THIS MANUAL IN ITS ENTIRETY. By following these operating, maintenance and safety instructions, you will prolong the life of your lift and promote safe operation.
Troy-Bilt TB500ML Warnings and Safety Instructions Read and understand all safety and operating instructions before using the mower lift. Never allow anyone unfamiliar with the safety or operating instructions to use the lift. Follow all safety and servicing instructions provided by the lawn mower’s manufacturer before using the lift. Do not modify the lift in any way. Any modifications will void any and all warranties and could compromise your personal safety.
Troy-Bilt TB500ML Warnings and Safety Decals CAUTION: Avoid injury! This symbol and text highlight potential hazards or death to the operator or bystanders that may occur if the hazards or procedures are ignored. NOTE: There can be additional safety information contained on parts and components sourced from suppliers that is not reproduced in this instruction manual.
Troy-Bilt TB500ML Warranty and Returns LIMITED WARRANTY For two years for residential use and one year for commercial use MoJack warrants the product against failure due to defect in material or workmanship when product is used properly. MoJack will replace any defective part at no cost. This warranty does not cover any product that has been altered or adjusted, or any product that has been misused or abused. THIS IS THE CUSTOMER’S SOLE AND EXCLUSIVE REMEDY.
Troy-Bilt TB500ML Parts List Item No. Part No. Qty.
Troy-Bilt TB500ML Hardware List Item No. Part No. Qty. 9 509-0040 2 Wheel Pad Support Rod 10 003-0005 2 Flange Head Bolt M10-1.5 X 60 11 003-0016 2 Flange Head Bolt M10-1.5 X 65 12 003-0007 2 Flange Head Bolt M8-1.25 X 16 13 002-0001 4 Nylon Lock Nut – M10-1.
Troy-Bilt TB500ML Assembly Instructions STEP 1 Remove lift from package. Inventory items to be certain all parts and hardware are present. If any parts or hardware are missing, please contact MoJack at 1-877-575-3173 or email us at parts@themojack.com. STEP 2 Assemble the Wheel 8 to the Base 4 by inserting Flange Bolt 11 through the wheel and threading the Nut 15 . Insert Flange Bolt through the Base, add Washer 14 and secure with Nylock Nut 13 . Repeat with second Wheel.
Troy-Bilt TB500ML Assembly Instructions STEP 4 Assemble Base with Wheels 4 to the Base Floor Tube 3 by inserting the two Flange Bolts 10 , Washers 14 and Nylon Lock Nuts 13 and tighten with 15mm wrenches. Washer 14 4 Base with Wheels Nylon Lock Nuts 13 Base Floor Tube 3 10 Flange Bolts STEP 5 Insert the Tower Assembly 1 to the Base with Wheels 4 and affix with Clevis Pin 17 and Hair Pin 18 as shown.
Troy-Bilt TB500ML Assembly Instructions STEP 7 Insert the Lift Arm 2 into the Carrier and insert the Clevis Pin 17 through the hole in Carrier and lock by fastening the Hair Pin 18 to the Clevis Pin. Carrier Hair Pin 18 17 Clevis Pin Lift Arm 2 STEP 8 Slide the Wheel Pad Lift Arms onto both sides of the Lift Arm secure with Push Pins 16 . 6 2 NOTE: The Wheel Pads can be moved in or out to fit different mower widths. Use the configuration that works best with your model of lawn mower.
Troy-Bilt TB500ML Operating Instructions Some steps of the Operating Instructions are repeated from the Assembly Instructions. The Operating Instructions will show a full working cycle of the mower lift. Before using the mower lift, carefully read this manual in its entirety.
Troy-Bilt TB500ML Operating Instructions Preparing for use (Steps 1 - 7) STEP 1 Unfolding the Mower Lift (if not applicable, skip to Step 2) • Remove Hair Pin and Clevis Pin from the Wheel Frame. • Remove the Tower out of the Wheel Frame. • Rotate Tower 180 degrees and insert into Wheel Frame. • Secure the Tower to the Wheel Frame by inserting Clevis Pin and Hair Pin.
Troy-Bilt TB500ML Operating Instructions STEP 3 Installing Wheel Pad Lift Arms • Slide Wheel Pad Lift Arms into both sides of the Lift Arm and secure with Push Pins. Lift Arm Push Pin Push Pin Wheel Pad Lift Arm Wheel Pad Lift Arm STEP 4 Preparing the handle • Push in side of handle and rotate from storage position to the operating position. Allow to seat into the locked position.
Troy-Bilt TB500ML Operating Instructions STEP 6 Aligning Wheel Pads to Fit Mower • Position the jack in front of the mower. • Remove Push Pins and adjust the wheel pad to align with the mower’s front tires. • Replace the Push Pins to lock the Wheel Pad Lift Arms to the Lift Arm. Wheel Pad Lift Arms must be equal distance from the Lift Arm to maintain proper balance.
Troy-Bilt TB500ML Operating Instructions STEP 9 Strapping Front Mower Tires to Wheel Pads • Secure the front mower tires to the Wheel Pads using the Safety Straps. Secure the hook on the Safety Strap to the Wheel Pad Slot. The Safety Strap hook should always be facing upward. • Extend the Safety Strap over the top of tire. • Insert the Wheel Support Rod through one hole on the Wheel Pad, through the loop on the Safety Strap and through the other side of the Wheel Pad. Secure with Large Hair Pin.
Troy-Bilt TB500ML Operating Instructions STEP 11 Raising Lift Arm to Locking Position • Raise the Lift Arm until the Carrier Locking Handle drops into one of the three Tower Holes. The Tower Locking Holes are the automatic safety engagement system. Tower Locking Holes are the automatic safety engagement system • The Carrier Locking Handle automatically drops into the Tower Holes as the Carrier passes the Tower Holes when raising. Locking engagement occurs at 14”, 19” and 24”.
Troy-Bilt TB500ML Operating Instructions STEP 14 Removing the Mower from the lift • Remove the Safety Straps from front mower tires. • Drive or roll the mower off of the Wheel Pads. STEP 15 Make sure drill is fully charged and set at highest torque. Raising the lift with a power drill (optional – power drill not included) The lift can be raised or lowered by using a variable speed corded drill (7 amp minimum) or variable speed cordless drill (18V minimum).
Troy-Bilt TB500ML Operating Instructions Preparing for Storage (Steps 16 - 20) STEP 16 Removing the Wheel Pads • Remove Push Pins and pull the Wheel Pad Lift Arms out of the Lift Arm. Lift Arm Push Pin Push Pin • Store the Push Pins in the Lift Arm to prevent loss. Wheel Pad Lift Arm Wheel Pad Lift Arm STEP 17 Removing the Lift Arm • While holding the Lift Arm, remove the Hair Pin and Clevis Pin from Lift Arm. Carrier • Slide the Lift Arm out of the Carrier.
Troy-Bilt TB500ML Operating Instructions STEP 18 Raise Carrier • Raise the Carrier by turning the Crank Handle clockwise until the Carrier Locking Handle drops into the top Tower Hole. Top Tower Hole Carrier Locking Handle STEP 19 Rotate Crank Handle to Storage position • Push in side of handle and rotate from operating position to the storage position. Allow to seat into the locked position.
Troy-Bilt TB500ML Operating Instructions STEP 20 Moving the Tower Assembly to Storage position • Remove Hair Pin and Clevis Pin from bottom of Tower Assembly. Tower Assembly • Raise the Tower out of the Base by pulling up on the Lift Handle. • Rotate Tower Assembly 180 degrees and lower into storage position. • Secure the Tower by inserting Clevis Pin and Hair Pin to lock Tower Assembly in storage position. Clevis Pin Hair Pin Clevis Pin Hair Pin THE LIFT IS NOW READY FOR STORAGE OR TRANSPORT.
Troy-Bilt TB500ML Maintenance Schedule • Before each use, always check for any worn, loose or damaged parts on the lift. If any damaged parts are present, do not use the lift and contact MoJack at 1-877-575-3173. Crank Handle Base • Clean and oil the entire screw thread after every fifty (50) uses or at least once a year using light machine oil. • Place lithium grease between the Crank Handle Base and the brass bearing after every fifty (50) uses or once a year.
Troy-Bilt TB500ML Supported Tire Sizes Wheel Pads accommodate wheel sizes from 10” – 17” (25cm – 43cm) Not for use with tires over 17” (43cm) in size 22
Troy-Bilt TB500ML Introducción Este manual contiene las instrucciones de montaje, las piezas, el funcionamiento, mantenimiento, ajuste y seguridad de su elevador. ANTES DE USAR SU EQUIPO ELEVADOR, LEA COMPLETAMENTE ESTE MANUAL. Al seguir estas instrucciones de funcionamiento, mantenimiento y seguridad, usted aumentará la vida útil de su elevador MoJack y promoverá un funcionamiento seguro.
Troy-Bilt TB500ML Advertencias e Instrucciones de Seguridad Lea y comprenda todas las instrucciones de seguridad y funcionamiento antes de usar el equipo elevador. Nunca permita que las personas no familiarizadas con las instrucciones de operación o seguridad, usen el elevador. Siga todas las instrucciones de seguridad y servicio ofrecidas por el fabricante de la podadora, antes de usar el equipo elevador. No modifique de ningún modo el equipo elevador.
Troy-Bilt TB500ML Advertencias y Calcomanías de Seguridad PRECAUCIÓN: ¡Evitar lesiones! Este símbolo y el texto de relieve los peligros potenciales o la muerte al operador oa otras personas que puedan ocurrir si se tienen en cuenta los riesgos o procedimientos. NOTA: No puede haber información adicional de seguridad contenida en piezas y componentes procedentes de proveedores que no se reproducen en este manual de instrucciones.
Troy-Bilt TB500ML Garantía y devoluciones GARANTÍA LIMITADA Por dos años únicamente para uso residencial, y un año para uso comercial, MoJack garantiza el producto contra fallas debidas a defectos en los materiales o la mano de obra, cuando el producto se usa adecuadamente. MoJack reemplazará cualquier parte defectuosa sin ningún costo. Esta garantía no cubre a ningún producto que se haya alterado o ajustado, ni a productos que se hayan usado inadecuadamente o excesivamente.
Troy-Bilt TB500ML Lista de Partes Número de artículo Número de parte Cantidad 1 509-0014 1 Conjunto de la torre 2 509-0026 1 Brazo de carga 3 509-0033 1 Tubo del piso de la base 4 509-0048 1 Base 5 509-0036 1 Canal de soporte de la base 6 509-0039 2 Plataforma para ruedas 7 009-0007 2 Tirante de seguridad 8 010-0013 2 Rueda Descripción 1 2 6 6 8 7 8 3 7 5 4 27
Troy-Bilt TB500ML Lista de Herrajes Número de artículo Número de parte Cantidad Descripción 9 509-0040 2 Varilla de soporte 10 003-0005 2 Perno de cabeza con reborde M10-1.5 X 60 11 003-0016 2 Perno de cabeza con reborde M10-1.5 X 65 12 003-0007 2 Perno de cabeza con reborde M8-1.25 X 16 13 002-0001 4 Contratuerca de nylon con – M10-1.
Troy-Bilt TB500ML Instrucciones de Ensamblado PASO 1 Saque el equipo elevador del empaque. Revise la lista de partes para asegurarse de que se encuentren todos los herrajes y piezas. Si faltan piezas o herrajes, póngase en contacto con MoJack llamando al 1-877-575-3173 o escríbanos al correo electrónico parts@themojack.com. PASO 2 Montar la rueda 8 a la Base 4 mediante la inserción de pernos de la brida 11 a través de la rueda y enhebrar la tuerca 15 .
Troy-Bilt TB500ML Instrucciones de Ensamblado PASO 4 Ensamble la base con ruedas 4 en el tubo del piso de la base 3 mediante la inserción de dos pernos con 10 , Arandela 14 y las contratuercas de nylon 13 y apriete con las llaves de 17 mm.
Troy-Bilt TB500ML Instrucciones de Ensamblado PASO 7 Inserte el brazo de carga 2 dentro de la transportadora e inserte el pasador de horquilla 17 a través del orificio en la transportadora y asegure sujetando el pasador estándar 18 en el pasador de horquilla. Transportadora Pasador estándar 18 17 Pasador de horquilla Brazo de carga 2 PASO 8 Deslice los topes de rueda 6 en el brazo elevador 2 . Inserte los pasadores de empuje 16 .
Troy-Bilt TB500ML Instrucciones de Operación Algunos pasos de las instrucciones de operación se repiten a partir de las instrucciones de montaje. Las instrucciones de operación mostrarán cómo operar el equipo elevador, muestran cómo preparar el equipo elevador para almacenarlo y cómo hacer pasar el equipo de la posición de almacenaje a la de trabajo. Antes de usar el equipo elevador, lea este manual con cuidado y por completo.
Troy-Bilt TB500ML Instrucciones de Operación Preparación del elevador para el uso (pasos 1 – 7) PASO 1 Despliegue el ascensor del cortacésped Pasador de horquilla (si no aplica , vaya al paso 2) • Retire la horquilla y el pasador de la estructura de la rueda. • Retire la torre de la estructura de la rueda. • Gire la torre 180 grados e inserte en la estructura de la rueda. • Asegure la torre a la estructura de la rueda insertando la horquilla y el pasador.
Troy-Bilt TB500ML Instrucciones de Operación PASO 3 Instalación de los topes de rueda • Deslice los topes de rueda en el brazo elevador y fíjelos provisoriamente con pasadores de empuje. Pasador de empuje Brazo elevador Pasador de empuje Tope de rueda Tope de rueda PASO 4 Preparación de la manija • Empuje en el lado de la manija y gire desde la posición de almacenamiento hasta la posición de operación. Permita que se asiente en la posición asegurada.
Troy-Bilt TB500ML Instrucciones de Operación PASO 6 Alineación de las plataformas para la rueda de modo que se ajusten a la podadora • Coloque las llantas delanteras de la podadora 6 pulgadas frente a las plataformas para las llantas. • Retire los pasadores de empuje y alinee las plataformas para las ruedas, de modo que las llantas delanteras se encuentren centradas sobre las plataformas para las ruedas.
Troy-Bilt TB500ML Instrucciones de Operación PASO 9 Enlace de las ruedas frontales de la cortacésped a las pastillas de las ruedas • Asegurar las llantas frontales de la cortacésped a las pastillas de las ruedas utilizando las correas de seguridad . Fije el gancho de la correa de seguridad a la ranura de la pastilla de la rueda. Siempre asegure las llantas frontales con las correas de seguridad adjuntas. El gancho de la correa de seguridad siempre debe estar mirando hacia arriba.
Troy-Bilt TB500ML Instrucciones de Operación PASO 11 Elevación del brazo de carga hasta la posición de aseguramiento • Eleve el brazo de carga hasta que la manija de bloqueo de la transportadora caiga dentro de uno de los dos orificios de la torre. • El bloqueo Carrier Manija automáticamente cae en los agujeros de la torre como el portador pasa los agujeros de la torre cuando se levantan. Acoplamiento de bloqueo se produce a los 14“, 19” y 24“.
Troy-Bilt TB500ML Instrucciones de Operación PASO 14 Retirar la podadora del equipo elevador • Quite los tirantes de seguridad de las llantas delanteras de la podadora. • Conduzca o ruede la podadora fuera de las plataformas para las llantas. PASO 15 Asegúrese de perforación está totalmente cargada y se fijó en alto torque.
Troy-Bilt TB500ML Instrucciones de Operación Preparación del equipo elevador para su almacenamiento (Pasos 16 al 20) PASO 16 Extracción de los topes de rueda • Extraiga los pasadores de empuje y retire los topes de rueda del brazo elevador. • Guarde los pasadores de empuje en el brazo elevador.
Troy-Bilt TB500ML Instrucciones de Operación PASO 18 Elevación de la transportadora • Eleve la transportadora haciendo girar la palanca de manivela hacia la derecha, hasta que la manija de aseguramiento de la transportadora caiga dentro del orificio de la torre. Orificios de la torre Manija de bloqueo de la transportadora PASO 19 Girar la palanca de manivela hasta la posición de almacenamiento • Empuje en el lado de la manija y gire desde la posición de operación hasta la posición de almacenamiento.
Troy-Bilt TB500ML Instrucciones de Operación PASO 20 Mueva el conjunto de la torre a la posición de almacenamiento • Retire el pasador estándar y el pasador de horquilla del fondo del conjunto de la torre. Conjunto de la torre • Eleve la torre hacia fuera de la base, tirando hacia arriba la manija de elevación. • Gire el conjunto de la torre 180 grados y hágalo descender hasta la posición de almacenamiento.
Troy-Bilt TB500ML Programa de Mantenimiento • Antes de cada uso, revise siempre que no haya ningún desgaste, piezas sueltas o dañadas en el equipo elevador. Si se detectan partes dañadas, no use el equipo elevador y póngase en contacto con MoJack a través de la línea directa 1-877-575-3173. Base de la palanca de manivela • Limpie y lubrique completamente el roscado del tornillo después de cada cincuenta (50) usos, o por lo menos una vez al año, usando aceite ligero para máquinas.
Troy-Bilt TB500ML Tamaños de las Llantas compatibles Las pastillas de las ruedas se ajustan a tamaños de ruedas de 25cm – 43cm (10” – 17”) No debe utilizarse con neumáticos de más de 43 cm (17 “) de tamaño 43