user manual

ManualsBrandsTroy-Bilt ManualsChipperChipper CS4265

Operator’s Manual

Chipper / Shredder

Models CS4210

CS4265

PRINTED IN U.S.A.

FORM NO.

769-00830A.fm

(4/15/04)

Model CS4210 Shown

IMPORTANT: Read safety rules and instructions carefully before operating equipment.

Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-

covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if

any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required

by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark

arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131

Cleveland, Ohio 44136-0019.

TROY-BILT LLC. P.O. BOX 361131, CLEVELAND, OHIO 44136-0019

Summary of content (12 pages)

PAGE 1
Operator’s Manual Chipper / Shredder Models CS4210 CS4265 Model CS4210 Shown IMPORTANT: Read safety rules and instructions carefully before operating equipment. Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brushcovered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any).
PAGE 2
TABLE OF CONTENTS Content Important Safe Operation Practices Assembling Your Chipper Shredder Know Your Chipper Shredder Operating Your Chipper Shredder Page 3 5 6 7 Content Maintaining Your Chipper Shredder Trouble Shooting Illustrated Parts List Warranty Page 9 12 13 16 FINDING MODEL NUMBER This Operator’s Manual is an important part of your new chipper shredder. It will help you assemble, prepare and maintain the unit for best performance. Please read and understand what it says.
PAGE 3
SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol - heed its warning.
PAGE 4
9. Never operate without the shredder hopper, chipper chute, or chute deflector properly attached to the machine. Never empty or change discharge bag while the engine is running. 10. Keep all guards, deflectors and safety devices in place and operating properly. 11. Keep your face and body back and to the side of the chipper chute while feeding material into the machine to avoid accidental kickback injuries. 12. Never operate this machine without good visibility or light. 13.
PAGE 5
SAFETY LABELS FOUND ON YOUR UNIT SECTION 2: ASSEMBLING YOUR CHIPPER SHREDDER IMPORTANT: This unit is shipped without gasoline or oil 1. in the engine. Be certain to service engine with gasoline and oil as instructed in the Briggs & Stratton Owner/ Operator manual packed with your unit. before operating your machine. Loose Parts In Carton • • • • Spring Latch 2.
PAGE 6
Attaching The Debris Collection Bag Attaching The Tow Bar (Model CS4210 Only) • • • • To attach the bag, place the opening of the bag completely over the chute deflector. Position the bag so that the wing knobs which secure the chute deflector to the impeller housing are completely covered. Pull on the drawstrap until the bag is tight around chute deflector opening. To attach the tow bar, remove the spring pin and clevis pin from the end of the tongue. See Figure 3.
PAGE 7
Handle Hopper Chipper Chute Spring Latch Starter Handle Chute Deflector Wing Knob Two Bar (Model CS4210 Only) Lock Rod Figure 4 SECTION 4: OPERATING YOUR CHIPPER SHREDDER • WARNING: The operation of any chipper shredder can result in foreign objects being thrown. Always wear the safety glasses provided with this unit or eye shields before chipping or shredding and while performing any adjustments or repairs. • OPEN NOTE: (A warm engine may not require choking).
PAGE 8
• Observe the following guidelines when shredding yard debris: Grasp the starter handle and pull the rope out slowly until resistance is felt. When it becomes slightly harder to pull the rope, slowly allow the rope to recoil. Then pull rope with a rapid, continuous, full arm stroke. Keep a firm grip on starter handle. • • NOTE: A “clanking” noise may be heard when pulling the starter rope. It is completely normal and does NOT indicate a malfunction of any kind.
PAGE 9
• Apply intermittent pressure (force, in short pulses) while feeding larger (2- 3-inch diameter) branches into the chipper chute, to avoid bogging or stalling the engine. Locking Buckle IMPORTANT: Never feed branches with a diameter greater than three (3) inches into the chipper chute. Doing so can result in serious damage to your unit’s chipper blades, flails or impeller. NOTE: For best performance, always operate the unit with sharp chipper blades.
PAGE 10
Chute Deflector: Lubricate the pivot points on the chute deflector with light oil once a season. Chute Deflector Engine: Refer to the Briggs & Stratton Owner/Operator manual packed with your unit for lubrication instructions. Shredder Screen Hairpin Clip Maintenance Housing Engine Refer to the Maintenance section of the Briggs & Stratton Owner/Operator manual packed with your unit.
PAGE 11
Chipper Blade Lock Washer & Nut Support Bracket Flange Nuts Support Brace Impeller Internal Hex Screw Hex Bolts & Saddle Washers Figure 10 Figure 9 NOTE: Use a 3/16” hex key (Allen) wrench on the outside of the blade and a 1/2” box (or socket) wrench on the inside of the impeller. See Figure 9. Hold the Allen wrench stationary and rotate the box (or socket) wrench to loosen the nut. • Chute Deflector Shredder Blade Internal Hex Screws Install a replacement blade (Part No.
PAGE 12
Storing Your Chipper Shredder • • • • Clean the equipment thoroughly. Wipe equipment with an oiled rag to prevent rust. Refer to engine manual for correct engine storage instructions Store unit in a clean, dry area. Do not store next to corrosive materials such as fertilizer. SECTION 6: TROUBLESHOOTING Problem Cause Remedy 1. Spark plug wire disconnected. 2. Fuel tank empty or stale fuel. 3. Throttle control lever (if equipped) not in correct starting position. 4. Choke not in CHOKE position.