Safe Operation Practices • Set-Up • Operation • Maintenance • Troubleshooting • Warranty Operator’s Manual 679 cc OHV Vertical Shaft Engine WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS ENGINE. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 Form No.
1 To The Owner Thank You This Operator’s Manual is an important part of your new engine. It will help you prepare and maintain the engine for the best performance. Please read and understand the contents before operating the engine. Table of Contents Important Safe Operation Practices........................................3 Safety Labels..............................................................................4 Set-Up...................................................................................
2 Important Safe Operation Practices WARNING! This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate the equipment. Failure to comply with these instructions may result in personal injury. When you see this symbol.
Maintenance & Storage 1. Keep the engine in safe working order 2. Allow the engine to cool at least five minutes before storing. Never tamper with safety devices. Check their proper operation regularly. 3. Check bolts and screws for proper tightness at frequent intervals to keep the engine in safe working condition. Visually inspect the engine for any damage. 4. Before cleaning, repairing or inspecting; stop the engine and make certain all moving parts have stopped.
3 Set-Up Gas & Oil • NOTE: The engine is shipped without gasoline and with motor oil in the engine. However, you MUST check the oil level before operating. Be careful not to overfill. Running the engine with insufficient oil can cause serious engine damage and void the engine warranty. Be careful not to spill fuel when refueling. Spilled fuel or fuel vapor may ignite. If any fuel is spilled, make sure the area is dry before starting the engine.
4 Controls and Features Finger Guard Air Cleaner Electric Starter Throttle Control Spark Plug Spark Plug Oil Fill Cap Oil Drain Oil Filter Figure 4-1 6 Throttle/Choke Control Oil Drain Fuel Cap The throttle/choke control is located on the mower and is used to aid in starting/stopping the engine and adjusting engine speeds. Refer to the Controls and Features section of the mower manual for more information regarding this control. Opening the oil drain valve will drain the oil from the engine.
5 Operation Pre-Operation Check 6. The engine is shipped without gasoline and with oil in the engine. See the Set-Up Section of this manual for instructions on adding gasoline and checking oil. Starting Engine Turn-Key Ignition 1. Insert the tractor key into the ignition module. 2. Place the PTO/Blade Engage lever to OFF position. 3. Engage the tractor’s parking brake . 4. Push the choke control (if equipped) upward into the choke on position.
6 Engine Maintenance WARNING: Shut off the engine before performing any maintenance. To prevent accidental start-up, disconnect the spark plug boot. Periodic inspection and adjustment of the engine is essential if high level performance is to be maintained. Regular maintenance will also ensure a long service life. The required service intervals and the kind of maintenance to be performed are described in the table below. Follow the hourly or calendar intervals, whichever occur first.
Replace Oil Filter This engine is equipped with a spin-on oil filter that should be replaced each time an oil change is performed, every season or 50 hours. Refer to Figure 6-5. 2. Remove dipstick and wipe clean with a cloth. 3. Pour oil into the dipstick tube. Do not over fill. With an oil filter change the high level amount of oil for this engine is 1900 ml (64.25 fl. oz.). 4. Install dipstick and turn to locked position before starting engine. 5. Start engine.
Spark Plug Service Electrode WARNING: DO NOT check for spark with spark plug removed. DO NOT crank engine with spark plug removed. WARNING: If the engine has been running, the muffler will be very hot. Be careful not to touch the muffler. 0.024-0.031 in. Figure 6-10 To ensure proper engine operation, the spark plug must be properly gapped and free of deposits. 4. Check that the spark plug washer is in good condition and thread the spark plug in by hand to prevent cross-threading. 1. 5.
Clean Engine Storage If the engine has been running, allow it to cool for at least half an hour before cleaning. Periodically remove dirt build-up from engine. Clean cooling fins every 25 hours. Clean with a brush or compressed air. IMPORTANT: Do not spray engine with water to clean because water could contaminate fuel. Using a garden hose or pressure washing equipment can also force water into the air cleaner or muffler opening.
7 Troubleshooting Problem Engine Fails to start Remedy 1. Choke not activated. 1. Place throttle/choke control in CHOKE position. 2. Spark plug boot disconnected. 2. Connect wire to spark boot. 3. Fuel tank empty or stale fuel. 3. Fill tank with clean, fresh gasoline. 4. Faulty spark plug. 4. Clean, adjust gap, or replace. 5. Reduced fuel flow/Blocked fuel filter. 5. Replace fuel filter as instructed in the Maintenance section. 6. Engine flooded. 6. Crank engine with throttle in FAST position.
8 Replacement Parts Component Part Number and Description 951-10292 Spark Plug 937-05145 Air Filter Assembly (Includes Pre-Filter) 951-12690 Oil Filter Phone (800) 800-7310 or (330) 220-4683 to order replacement parts or a complete Parts Manual (have your full model number and serial number ready). Parts Manual downloads are also available free of charge at www.mtdproducts.com.
Notes 14 9
Medidas importantes de seguridad • Configuración • Funcionamiento • Mantenimiento • Solución de problemas • Garantía Manual del Operador Motor de 679 cc con eje vertical y válvulas en cabeza ADVERTENCIA LEA Y RESPETE TODAS LAS NORMAS DE SEGURIDAD E INSTRUCCIONES INCLUIDAS EN ESTE MANUAL ANTES DE PONER EN FUNCIONAMIENTO ESTA MOTOR. SI NO RESPETA ESTAS INSTRUCCIONES PUEDE PROVOCAR LESIONES PERSONALES. MTD LLC.
1 Al propietario Gracias Este Manual del Operador es una parte importante de su nuevo motor. Le ayudará a preparar y mantener la unidad para obtener los mejores resultados. Antes de operar el motor lea cuidadosamente y comprenda todo el manual. Índice Medidas importantes de seguridad....................... 3 Configuración........................................................... 5 Controles y Características...................................... 6 Funcionamiento.........................................
2 Medidas importantes de seguridad ¡ADVERTENCIA! La presencia de este símbolo indica que se trata de instrucciones de seguridad importantes que debe respetar para evitar poner en riesgo su seguridad personal y/o material y la de los demás. Lea y siga todas las instrucciones de este manual antes de poner en funcionamiento este equipo. Si no respeta estas instrucciones puede provocar lesiones personales. Cuando vea este símbolo. TENGA EN CUENTA LA ADVERTENCIA.
9. Átese el cabello si lo lleva largo y no use alhajas. 10. No use ropa demasiado holgada, con cordones colgantes o partes que se puedan enganchar. 11. Para encender el motor, jale de la cuerda lentamente hasta que sienta resistencia, luego jale rápidamente (Si no es de arranque eléctrico). 12. Antes de arrancar el motor, retire todos los equipos externos/cargas del motor. 13.
3 Configuración Gasolina y aceite 2. NOTA: El motor se despacha sin gasolina ni aceite en su interior. Hacer funcionar el motor sin suficiente aceite puede causarle graves daños y anula la garantía del motor. Inserte la varilla en el cuello de llenado de aceite. Gire la varilla de 1 / 4 vuelta en la posición de bloqueo en su totalidad asiento. Vea la Figura 3-2. ¡ADVERTENCIA! Siempre mantenga las manos y los pies alejados de las piezas móviles del equipo. No utilice fluidos comprimidos para arrancar.
4 Controles y Características Dedo de la Guardia Depurador de aire Arranque eléctrico Conjunto del cuerpo del acelerador Bujía de encendido Bujía de encendido Tapa del aceite Tubo de drenaje Filtro de aceite Figura 4-3 6 Control del acelerador Tubo de drenaje Tapa de la gasolina Control del acelerador se encuentra en la cortadora de césped y se utiliza para ayudar a arrancar / parar el motor y el ajuste de las velocidades del motor.
5 Funcionamiento Control previo al funcionamiento El motor se envía sin gasolina y con aceite en el motor. Consulte la Sección Configuración incluida en este manual para ver las instrucciones para la carga de gasolina y comprobación del aceite. Encendido del motor 6. PRECAUCIÓN , durante NO mantenga la llave en la posición ARRANQUE más de diez segundos por vez. Si lo hace, puede ocasionar daños al arrancador eléctrico del motor. 6.
6 Mantenimiento y Adjustes ¡ADVERTENCIA! Apague el motor y eliminar Arranque eléctrico pulsar tecla (si lo tiene) antes de realizar el mantenimiento. Para evitar una puesta en marcha accidental, desconecte la funda de la bujía. La inspección y los ajustes periódicos del motor son esenciales si se desea mantener un alto nivel de desempeño. El mantenimiento regular también garantizará una prolongada vida útil del motor.
IMPORTANTE: El aceite de motor usado puede causar cáncer de piel si entra en contacto con la piel de manera reiterada y por períodos prolongados. Si bien esto es improbable a menos que manipule aceite usado todos los días, es recomendable lavarse muy bien las manos con agua y jabón inmediatamente después de haber manipulado aceite usado. 1. Drenaje de aceite. Vea la sección de drenaje de aceite. 2. Quite el filtro de aceite. Deseche el aceite viejo filtro correctamente. 3.
5. Quitar la espuma pre-filtro de aire de todo el papel de filtro. Vea la Figura 6-6. Sustituya el elemento de papel cuando sucio o dañado. Limpia el elemento de espuma o sustituya cuando dañado. 8. Coloque la tapa del filtro de aire. Vea la Figura 6-8. Gire tornillos en sentido horario hasta que quede ajustado. Revise si hay desalineación. Funda de bujía NOTA: El elemento de espuma no puede ser comprado por separado. Filtro de aire sólo se vende como un conjunto.
Limpie el Motor Si el motor ha estado funcionando, déjelo enfriar durante por lo menos media hora antes de limpiarlo. De manera regular, extraiga el pasto y la acumulación de suciedad del motor. Limpie las aletas de refrigeración de 25 horas. Limpie con un cepillo o aire comprimido. IMPORTANTE: No rocíe el motor con agua para limpiarlo porque el agua podría contaminar el combustible.
7 Solución de Problemas Problema El motor no arranca Solución 1. No se ha activado el cebador. 1. Coloque el control del regulador/cebador en la posición CHOKE (cebador). 2. Alambre de bujía desconectado. 2. Unir el alambre a la bujía. 3. Depósito de combustible combustible vacío o añejo. 3. Llenar el tanque de la gasolina limpia, fresca. 4. Bujía defectuosa. 4. Limpio, ajuste el hueco, o sustituir. 5. Reducción del flujo de combustible y filtro de combustible bloqueados. 5.
Notas 8 13
MTD LLC, P.O.