SERVICE AND MAINTENANCE Follow the maintenance schedule given below.
SERVICE AND MAINTENANCE before | tier [every [very ferry Joey recovery foo see Ba [mos [0 [5 [so foo Jao [EO | engine Use {Hours [Hours |Hours [Ours {ours | Hours 4 | Manual Check That A Hardware sin Vv Plate &Secure Check Engine Mounting Alt Torque Tightento325-4501nvbs 37-50-11) v v Check Blade Mount Nut Torque (Tighten to 70-90 ft-tbs (35-122 N-m}} v v v Check Spark Plug Condition & Gap Vv vv Engine Break-In 04 Change Vv Vv Change Engine Check Fuel System (tines, Toni, Gap, Fittings} v v vo Cheek Spark A
SERVICE AND MAINTENANCE «Clean the poof the mover deck, under ie spindle covers and bet area. See Figure 31. Freon the tractor aerator's seat, start the engine and engage tie PTO. Allow fo un as needed. Disengage the PTO ard stop the engine, . Turn of the water supply. F. Pauli back the Jock collar of the nozzle adapter to disconnect the nozzle adapter from the deck wash nozzle.
SERVICE AN Ye + Additional to dealing the tractor before operating and storing, donor attempt to now unusually tal grass (10 {25.6 cmp or bighead, dry grass e.g. pasture or sol dry Eaves, Dry grass oF leaves may contact the engine exhaust and/or hulls up on the maser deck presenting a potential fire hazard, Sterling the Tractor Owlish the machine bo coat an apn area for at east five ‘minutes before storing.
SERVICE AND MAINTENANCE NOTE: Place an absorbent towel beneath the oif filter to keep off off the clutch, NOTE Observe proper disposal laws natl regulators for gas, ofl, etc.to protect the environment, NOTE: Maintenance, repair 1 replacement of the emission control! devices and systems which are beg done at owners ‘expense may be performed by any engine repair establishment individual, Warranty Nepalis must be performed by an authorized dealer.
SERVICE AND MAINTENANCE Removing the Tractor from Storage . Check the engine oll. Fully charge the hatchery and flatmate the tress the recommended pressure. See te side wall For proper ire inflation pressure. $l the fuel tank with dean, fresh gasoline. Start the engine and allow to dle for a few minutes to ensure engines operating proper . Drive the tractor without a oad to make certain al the tractor systems are functioning proper. Adjustments ~ ow ADJUSTING TECH LIFT PEDAL 1.
SERVICE AND MAINTENANCE . Rotate she blade nearest the discharge chute so that its parallel with the tractor, . Metastasize the distance farm the grant of the blade tlp to the ground and the rear of the blade Hp to the grind. The fest measurement taken should be between 1716-147 (2-6 mm} fess than the second measurement. . Determine Ihe approximate distance necessary for proper adjustment and proceed, f necessary. .
SERVICE AND MAINTENANCE Mace the tractor to a elev surface, disengage the PTO, tog the engine, face the RH and Li drive control levers fully outward into the park brake engaged position. Ti sere ase twa methods for removing the belt, to remove the belt by releasing belt tension go on to Step 3, lo remove lhe belt by roofing the hel off the PIO pulley skip ahead to Step. A WARNING Use caution to avoid pinching your fingers when roofing the belt off the PTO pulley. 3.
SERVICE AND MAINTENANCE Horehound b. Remove the third owe pin a) from the clevis pin (b) that secures Lhe front deck control rod (} the front deck it bracken (4). Remove the levees pin bl, See Figure M, a2 Figure 4 ¢. Carefully maneuver the deck aut fom beneath the tractor.
SERVICE AND MAINTENANCE 42" Decks 60" Decks Fare 48 Tractor Blade Care FISH Before performing any maintenance, disengage the PTO and nave telegrapher drive control levers fully outward into the Park Brake engaged position. leaving the tractor unattended, turn the Ignition key to the STOP ‘position and remove key. Protect your hands by using heavy gloves manhandling the blades, When serving the tractor deck, he careful not to cut yourself on the sharpened blades.
SERVICE AND MAINTENANCE 2. Sea 15/16 wrench ta hold the hex nut on tap of the spindle assembly when looseness the hex uta) securing the blade (b). A block of wooed 0) may be placed between the deck housing and ire cutting ede of the bide breading loose the hex ut) securing the blade. See Figure 49. Figure 49 When re-installing the blades, be sure they are installed so that the wings are pointing upward toward the tap of the deck, Tighten the fie aus (a} to 70-90 phi-1bs {95-922 Nome.