Safe Operation Practices • Set-Up • Operation • Service • Troubleshooting Operator’s Manual Lawn Tractor Table of Contents Safe Operation Practices......................................... 2 Product Care............................................................14 Assembly & Set-Up................................................... 6 Parts/Warranty............... See Separate Supplement Controls & Operation..............................................
Important Safe Operation Practices WARNING This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol.
7. Do not tow heavy pull behind attachments (e.g. loaded dump cart, lawn roller, etc.) on slopes greater than 5 degrees. When going down hill, the extra weight tends to push the tractor and may cause you to loose control (e.g. tractor may speed up, braking and steering ability are reduced, attachment may jack-knife and cause tractor to overturn). Children 1. b. c. Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner.
Safety Symbols This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate. Symbol Description READ THE OPERATOR’S MANUAL(S) Read, understand, and follow all instructions in the manual(s) before attempting to assemble and operate DANGER — ROTATING BLADES Never carry passengers. Never carry children, even with the blades off.
(OK) Figure 1 Slope Gauge e da s h e d lin 15°/25% Slope 5% 15°/2 USE THIS SLOPE GAUGE TO DETERMINE IF A SLOPE IS TOO STEEP FOR SAFE OPERATION! To check the slope, proceed as follows: 1. Remove this page and fold along the dashed line. 2. Locate a vertical object on or behind the slope (e.g. a pole, building, fence, tree, etc.) 3. Align either side of the slope gauge with the object (See Figure 1 and Figure 2 ). 4.
Assembly & Set-Up 2 Thank You Thank you for purchasing this product. It was carefully engineered to provide excellent performance when properly operated and maintained. Please read this entire manual prior to operating the equipment. It instructs you how to safely and easily set up, operate and maintain your machine. Please be sure that you, and any other persons who will operate the machine, carefully follow the recommended safety practices at all times.
2. 3. Remove the plastic cover, if present, from the negative battery terminal and attach the black cable to the negative battery terminal (–) with the bolt (a) and hex nut (b). See Figure 2-2. Position the red rubber boot (c) over the positive battery terminal to help protect it from corrosion. Note: If the battery is put into service after the date shown on top/side of battery, charge the battery as instructed in the Service section your Operator’s Manual on page 8 prior to operating the tractor. 2.
Tire Pressure 2. WARNING Equal tire pressure should be maintained at all times. Refer to the tire sidewall for proper pressure. Fill the fuel tank with gasoline. Use only clean, fresh (no more than 30 days old), unleaded gasoline. Fill tank to the base of the filler neck to allow space for fuel expansion. DO NOT TOP OFF THE TANK WITH FUEL. See Figure 2-9. Setting the Deck Gauge Wheels (If Equipped) Move the tractor to a firm and level surface, preferably pavement, and proceed as follows: 1.
Attaching the Hood Scoop (If Equipped) Moving the Tractor Manually On some tractors, a hood scoop may be included. If the hood scoop was not installed on the hood of your tractor at the factory, refer to the following steps to install the hood scoop: Refer to Figure 2-1 and proceed to your applicable model. 1. Cut the cable ties securing the hood scoop to the tractor. 2. Remove the four screws pre-installed in the hood scoop and retain for Step 4. 3.
3 Controls & Operation To set the parking brake: Fully depress the parking brake pedal. Move the parking brake lever all the way down and into the parking brake position (PARK BRAKE ON) and then release the brake pedal to allow the parking brake to engage. Hydrostatic Set-Up Ammeter † Throttle/Choke Control Lever Ignition Switch Module To release the parking brake: Depress the brake pedal and the parking brake lever will automatically move out of the parking brake position.
Shift Lever (If Equipped) Ignition Switch Module Deck Lift Lever Foot Control CVT & CVT The lawn tractor will have one of the following ignition switches. Refer to Figure 3-3 to identify which switch your machine utilizes and follow the applicable instructions for proper operation. The deck lift lever is located on the lawn tractor’s right fender. It is used to change the height of the cutting deck. To use, move the lever to the left, then place in the position best suited for your application.
To use the REVERSE CAUTION MODE: Setting the Cutting Height Important: The operator MUST be seated in the lawn tractor seat. 1. 1. Start the engine as instructed on page 12. 2. Turn the key from the NORMAL DRIVING MODE (Green) position to the REVERSE CAUTION MODE (Yellow) position of the ignition switch module. See Figure 3-4. Reverse Push Button Indicator Light Reverse Caution Mode Position Normal Driving Mode Stop position Start position 2.
Foot Control CVT Engaging the Blades 1. Depress the clutch-brake pedal to release the parking brake and let the pedal up. 1. Depress the brake pedal to release the parking brake and let the pedal up. 2. Move the throttle lever into the FAST (rabbit) position. 2. Move the throttle lever into the FAST (rabbit) position. Engaging the PTO (blade engage) transfers power to the cutting deck. To engage the blades, proceed as follows: 3.
4 Product Care Maintenance Schedule Before Each use Every 10 Hours Every 25 Hours Every 50 Hours Every 100 Hours P P P P P P Check/Clean Engine Intake Screens & Cooling Fans * Check/Clean Exhaust Manifold, Muffler Pipe & Muffler Shields * Check/Clean Hood/Dash Panel Louvers * Check/Clean Top & Underside of Deck, Under and Around Spindle Covers & Belt Area * Check/Clean Around Fuses, Wiring and Wiring Harnesses * Check/Clean Around Transmission, Axle and Fans * P P P P P P P P P P P P P Clean Hood
deck engaged for a minimum of two minutes, allowing the underside of the deck to thoroughly rinse. 9. Move the rider’s PTO into the disengaged (OFF) position. 10. Turn the ignition key to the STOP turn the rider’s engine off. 11. Turn the water off and detach the hose coupler from the water port on your deck’s surface. • Clean the top of the mower deck, under the spindle covers and belt area. See Figure 4-3. Engine Refer to the Engine Operator’s Manual for engine maintenance instructions.
Oil Drain Sleeve Models WARNING If the rider has been recently run, the engine, muffler and surrounding metal surfaces will be hot and can cause burns to the skin. Let the engine cool for at least five minutes Exercise caution to avoid burns. To complete the oil change, proceed as follows: 1. Run the engine for a few minutes to allow the oil in the crankcase to warm. Warm oil will flow more freely and carry away more of the engine sediment which may have settled at the bottom of the crankcase.
3. Connect the second cable (negative –) to the other post of the jumper battery. 4. Make the final connection on the engine block of the rider, away from the battery. Attach to a unpainted part to ensure a good connection. CAUTION 1. With the rider parked on a firm, level surface, place the lever for lifting the platform on the second to the top notch (second highest position) and rotate the blade as close to the discharge channel that is parallel to the rider. 2.
3. Remove the belt-keeper rod, from around the rider’s engine pulley, by removing the selftapping screw (A) that secures it. See Figure 4-11. 8. On 38” decks, gently slide the cutting deck toward the front of the tractor carefully guiding the hooks on the deck off of the deck stabilizer rod. See Figure 4-13. Deck Installation To install the deck, reverse the Deck Removal instructions on page 18-19. Tires WARNING Never exceed the maximum inflation pressure shown on the sidewall of the tire.
Important: If the cutting edge of the blade has already been sharpened to within 1-5⁄8” from the edge, or if any metal separation is present, replace the blades with new ones. See Figure 4-17. Changing the Deck Belt 3. It may also be necessary to loosen the hex nut on the left idler pulley to get the belt off the pulley and around the belt guard. 4. Carefully remove the deck belt from around the two spindle pulleys and the two deck idler pulleys. See Figure 4-18. 5.
Notes 20
Medidas de seguridad • Configuración • Funcionamiento • Servicio • Solución de problemas Manual del Operador Tractor cortacésped Índice Medidas de seguridad.................................................. 2 Montaje y Configuración............................................. 6 Controles y Funcionamiento.....................................10 Servicio.........................................................................14 Piezas/Garantía..........
Importantes medidas de seguridad ADVERTENCIA Este símbolo indica instrucciones de seguridad importantes que, de no seguirse, podrían poner en peligro la seguridad personal y/o la propiedad suya y de terceros. Lea y cumpla todas las instrucciones de este manual antes de intentar hacer funcionar esta máquina. Si no sigue estas instrucciones, se pueden provocar lesiones personales. Cuando vea este símbolo.
el suelo. giros amplios para el acodillamiento. 4. No utilice colector de césped en pendientes empinadas. 6. Desplácese lentamente y deje distancia adicional para detenerse. 5. No corte el césped húmedo. La falta de tracción puede hacer que patine. 7. No cambie a punto muerto para bajar por inercia. 6. No cambie a punto muerto para bajar por inercia. El exceso de velocidad puede hacer que el operador pierda el control de la máquina y se produzcan lesiones graves o la muerte.
No modifique el motor Para evitar lesiones graves o la muerte, no modifique el motor de ninguna manera. Si altera la configuración del regulador, el motor se puede desbocar y funcionar a velocidades que no son seguras. Nunca cambie la configuración de fábrica del regulador del motor. Cuando sea necesario, los modelos están equipados con líneas de combustible y tanques de combustible de baja penetración para controlar las emisiones por evaporación.
(OK) Figura 1 Indicador de pendiente Pendiente de 15°/25% L nt íne a d e pu Figura 2 (MUY EMPINADA) os a 1 5 ° /25% ¡USE ESTE INDICADOR DE PENDIENTE PARA DETERMINAR SI UNA PENDIENTE ES DEMASIADO EMPINADA PARA SU SEGURIDAD! Para comprobar la pendiente, proceda de la siguiente manera: 1. Separe esta página y pliéguela por la línea de puntos. 2. Ubique un objeto vertical que se encuentre sobre o detrás de la pendiente (un poste, un edificio, un cerco, un árbol, etc.) 3.
Montaje y Configuración 2 Muchas gracias Gracias por comprar este producto. Ha sido cuidadosamente diseñado para brindar excelente rendimiento si se lo hace funcionar y se lo mantiene correctamente. Por favor lea todo este manual antes de hacer funcionar el equipo. El manual le indica cómo configurar, hacer funcionar y mantener la máquina de manera fácil y segura.
Herramientas necesarias • Extracción de la traba de seguridad Llave ajustable o juego de llaves de vaso su lugar. Instalación del asiento ADVERTENCIA Conexión de los cables de la batería ADVERTENCIA PROPOSICIÓN 65 de California: Los bornes y contactos de la batería, y los accesorios afines contienen plomo y compuestos de plomo, sustancias químicas que el Estado de California considera que pueden producir cáncer y daños en el sistema reproductivo.
Cubierta de instrumentos (si está equipado) Presión de los neumáticos Hay dos ipos de velo. Una cubierta para el / / T-Estilo 1/3/5 K y otro para el salpicadero S-Style. ADVERTENCIA Se debe mantener una presión uniforme para todos los neumáticos en todo momento. Nunca exceda la presión máxima de inflado que se indica en los laterales de los neumáticos. Continuar por debajo de 1/3/5 / K / T-Style, salte a la sección S-estilo para el tablero de estilo S. 1/3/5/K/T-Estilo Cubierta 1.
Ajuste de las ruedas de calibración de la plataforma (si está equipado) Instalación de la toma de aire del capó (si está equipado) Mueva el tractor a una superficie firme y nivelada, preferentemente sobre el pavimento, y realice lo siguiente: Algunos tractores vienen con una toma de aire del capó. Si la toma de aire no fue instalada en la fábrica sobre el capó de su tractor, siga los siguientes pasos para instalar la toma de aire del capó: 1. 2.
3 Controles y Funcionamiento Para poner el freno de mano: Presione totalmente el pedal del freno. Mueva la palanca del freno de mano totalmente hacia abajo a la posición de freno de mano (CON FRENO DE MANO) y luego suelte el pedral de freno para permitir que el freno de mano enganche.
Palanca de cambios (si está equipada) Módulo del interruptor de contacto Palanca de elevación de la plataforma Pedal de CVT y CVT El tractor cortacésped tendrá uno de los siguientes interruptores de contacto. Consulte la Figura 3-3 para identificar qué interruptor utiliza su máquina y siga estas instrucciones para un funcionamiento adecuado. La palanca de elevación de la plataforma se encuentra sobre el guardabarros derecho del tractor cortacésped.
Para utilizar el MODO PRECAUCIÓN MARCHA ATRÁS: Ajuste de la altura de corte Importante: El operador DEBE estar sentado en el asiento del tractor cortacésped. 1. 1. Ponga en marcha el motor como se indica en la página 12. 2. Gire la llave desde la posición MODO MARCHA NORMAL (verde) hasta la posición de MODO PRECAUCIÓN MARCHA ATRÁS (amarillo) del módulo del interruptor de contacto. Consulte la Figura 3-4.
CVT Pedal de CVT 1. Presione el pedal de embrague-freno para liberar el freno de mano y deje que suba el pedal. 1. Presione el pedal de freno para liberar el freno de mano y deje que suba el pedal. 2. Mueva la palanca del acelerador a la posición RÁPIDO (liebre). 2. Mueva la palanca del acelerador a la posición RÁPIDO (liebre). 3. Coloque la palanca de cambios en posición AVANCE (F) o MARCHA ATRÁS (R). 3. Coloque la palanca de cambios en posición AVANCE (F) o MARCHA ATRÁS (R).
Cuidado del producto 4 Programa de mantenimiento Antes de cada uso Compruebe/Limpie las Pantallas de Entrada de Motor y los Ventiladores de Enfriamiento * Revisar/Limpiar el Colector de Escape, el Silenciador y los Escudos del Silenciador * Compruebe/Limpie la Campana/Tablero Tableros * Compruebe/Limpie la parte superior y la parte inferior de la cubierta, debajo y alrededor de las cubiertas del eje y el área de la correa * Comprobar / limpiar alrededor de los fusibles, el cableado y los arneses de cablea
5. Abra el suministro de agua. 6. Mientras está sentado en la posición del operador del tractor, arranque el motor y coloque la palanca del regulador en la posición FAST (velocidad rápida). 7. Mueva la PTO del tractor a la posición de activación (ON). 8. Permanezca en la posición del operador con la plataforma enganchada durante dos minutos como mínimo, permitiendo que la parte inferior de la plataforma de corte se lave a fondo. 9. Mueva la PTO del tractor a la posición de desactivación (OFF). 10.
Modelos de manga de drenaje de aceite ADVERTENCIA Si el motor ha estado en funcionamiento recientemente, el motor, el silenciador y las superficies metálicas circundantes estarán calientes y pueden causar quemaduras en la piel. Tenga precaución para evitar quemaduras. Para realizar el cambio de aceite, proceda de la siguiente manera: 1. 2. 3. 4. Deje el motor funcionando durante algunos minutos para que el aceite del cárter se caliente.
Arranque con puente Nivelación de la plataforma ADVERTENCIA Nunca arranque con puente una batería dañada o congelada. Asegúrese de que los vehículos no se toquen y los motores están apagados. No permita que las pinzas de los cables se toquen. Importante: Nunca haga arrancar la batería descargada de su tractor con un puente a la batería de un vehículo en marcha. 1. Conecte el cable positivo (+) al borne positivo (+) de la batería descargada de su tractor. 2.
4. Retire la correa (C) de alrededor de la polea del motor del tractor y de las poleas locas. Consulte la Figura 4-11. 5. Mirando la plataforma de corte desde el lado izquierdo del tractor, ubique el pasador de chaveta que sujeta la varilla de soporte de la plataforma del lado posterior izquierdo de la plataforma. Consulte la Figura 4-12.
Cambio de la correa de la plataforma 3. ADVERTENCIA Recuerde apagar el motor, sacar la llave, desconectar los cables de las bujías y hacer masa contra el motor para evitar que se encienda accidentalmente antes de sacar la correa. ADVERTENCIA Todas las correas del tractor cortacésped se desgastan y se las debe cambiar si presentan signos de desgaste. Importante: Las correas en V del tractor están diseñadas especialmente para que se enganchen y desenganchen sin riesgos.
Notas 20