Operator’s Manual TB25C 2-Cycle Trimmer SAVE THESE INSTRUCTIONS IMPORTANT: Read this manual thoroughly before using this product. Follow all instructions.
TABLE OF CONTENTS SERVICE Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• IMPORTANT SAFETY INSTRUCTIONS • READ ALL INSTRUCTIONS BEFORE OPERATING SAFETY WARNINGS FOR GAS UNITS WARNING: WARNING: When using the unit, all safety instructions must be followed. Please read these instructions before operating the unit in order to ensure the safety of the operator and any bystanders. Please keep these instructions for later use. • • • • • • • • • • • • • Gasoline is highly flammable and its vapors can explode if ignited.
• • • • • • • • • • OTHER SAFETY WARNINGS Do not operate the unit faster than the speed needed to do the job. Do not run the unit at high speed when not in use. Do not force the unit. It will do a better, safer job when used at the intended rate. Always turn the unit off when operation is delayed or when carrying the unit from one location to another. Make sure all moving parts come to a complete stop. Before setting the unit down, always make sure the engine is off and all moving parts have stopped.
• SAFETY & INTERNATIONAL SYMBOLS • This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety, assembly, operating and maintenance and repair information. SYMBOL MEANING SYMBOL • SAFETY ALERT SYMBOL MEANING • ON/OFF STOP CONTROL Indicates danger, warning or caution. May be used in conjunction with other symbols or pictographs.
KNOW YOUR UNIT APPLICATIONS • • • Muffler Cutting grass and light weeds Edging Decorative trimming around trees, fences, etc. Spark Plug Starter Rope Grip ASSEMBLY TOOLS REQUIRED • #2 Phillips screwdriver Shaft Grip Air Filter Cover Handle Fuel Cap On/Off Switch Throttle Control Lower Shaft Housing Coupler Upper Shaft Housing Choke Lever Cutting Head Shield Primer Bulb Cutting Head Line Cutting Blade SPECIFICATIONS* Engine Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ASSEMBLY INSTALLING THE CUTTING HEAD SHIELD Slot Cutting Head Shield WARNING: To prevent serious personal injury, never operate the unit without the cutting head shield in place. 1. Remove the wing nut and washer from the cutting head shield. 2. Insert the short tab (the one without a hole) on the mount bracket into the slot on the cutting head shield (Fig. 1). 3. Rotate the cutting head shield counterclockwise to align the hole on the cutting head shield with the hole on the mount bracket (Fig. 1). 4.
1/8 Fig. 5 INSTALLING AND ADJUSTING THE HANDLE Handle Installing the Handle 1. Push the handle down onto the upper shaft housing (Fig. 6). Make sure the hex bolt hole faces to the left (Fig. 6). 2. Insert the bolt into the hex bolt hole and push it through (Fig. 7). Place the washer onto the bolt (Fig. 7). Screw the wing nut onto the bolt, but do not tighten the wing nut completely (Fig. 7). 3. Hold the unit in the operating position (Fig. 12).
OIL AND FUEL FUELING THE UNIT OIL AND FUEL MIXING INSTRUCTIONS The use of old and/or improperly mixed fuel is the most common cause of performance problems. Use only fresh, clean unleaded gasoline. Follow the instructions carefully for the proper gasoline/oil mixture. WARNING: Gasoline is extremely flammable. Ignited vapors may explode. Always stop the engine and allow it to cool before filling the fuel tank. Do not smoke while filling the tank. Keep sparks and open flames at a distance from the area.
STARTING AND STOPPING WARNING: Operate this unit only in a well-ventilated outdoor area. Carbon monoxide exhaust fumes can be lethal in a confined area. On/Off Switch Off (O) WARNING: Avoid accidentally starting the unit. To avoid serious injury, the operator and the unit must be in a stable position when pulling the starter rope (Fig. 11). WARNING: The cutting head will spin during the starting procedure. Wear protective clothing and observe all safety instructions to prevent serious personal injury.
OPERATION HOLDING THE UNIT WARNING: Always wear eye, hearing, hand, foot and body protection to reduce the risk of injury when operating this unit. WARNING: To prevent serious personal injury, avoid arm contact with the engine while operating the unit. The engine may be extremely hot. • • • • • • Stand in the operating position (Fig. 12). Stand up straight. Do not bend over. Keep feet apart and firmly planted. Hold the shaft grip with the right hand. Keep the right arm slightly bent.
MAINTENANCE MAINTENANCE SCHEDULE WARNING: To avoid serious personal injury, always stop the engine and allow it to cool before cleaning or maintaining the unit. Never perform cleaning or maintenance while the unit is running. Disconnect the spark plug wire to prevent the unit from starting accidentally. Perform these required maintenance procedures at the frequency stated in the table. These procedures should also be a part of any seasonal tune-up.
Cutting Head Line Line Loop Fig. 16 MAINTAINING THE AIR FILTER Air Filter Failure to maintain the air filter can result in poor performance or can cause permanent damage to the engine. Engine failure due to improper air filter maintenance is not covered by the product warranty. Cleaning the Air Filter 1. Open the air filter cover: press in the lock tab and swing the air filter cover to the right (Fig. 17). 2. Remove the air filter from inside the air filter cover (Fig. 17). 3.
MAINTAINING THE SPARK PLUG 1. Stop the engine and allow it to cool. Grasp the spark plug boot firmly and pull it from the spark plug. 2. Clean around the spark plug. Remove the spark plug from the cylinder head with a 5/8-inch socket, turning counterclockwise. WARNING: Do not sand blast, scrape or clean spark plug electrodes. Grit in the engine could damage the cylinder. 0.025 in. (0.635 mm) 3. Inspect the spark plug.
TROUBLESHOOTING PROBLEM SOLUTION THE ENGINE WILL NOT START The fuel tank is empty Fill the fuel tank with properly-mixed fuel The primer bulb was not pressed enough Press the primer bulb 10 times or until fuel is visible The engine is flooded Move the choke lever to Position 3, squeeze the throttle control and pull the starter rope until the engine starts The fuel is old (over 30 days) and/or improperly mixed Drain the fuel tank and add fresh, properly-mixed fuel The spark plug is fouled Replace
MANUFACTURER’S LIMITED WARRANTY FOR: The limited warranty set forth below is given by Troy-Bilt LLC (Troy-Bilt) with respect to new merchandise purchased and used in the United States, its possessions and territories. Troy-Bilt warrants this product against defects in material and workmanship for a period of two (2) years commencing on the date of original purchase and will, at its option, repair or replace, free of charge, any part found to be defective in material or workmanship.
Manual del Operador TB25C Recortadoras de 2 ciclos CONSERVE ESTAS INSTRUCCIONES IMPORTANTE: Lea este manual por completo antes de utilizar este producto. Siga todas las instrucciones.
ÍNDICE SERVICIO Servicio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Seguridad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Conozca su unidad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Especificaciones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Montaje . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• INSTRUCCIONES DE SEGURIDAD IMPORTANTES • LEA TODAS LAS INSTRUCCIONES ANTES DE USAR LA UNIDAD ADVERTENCIAS DE SEGURIDAD PARA LAS UNIDADES A GASOLINA ADVERTENCIA: La gasolina es sumamente inflamable y sus vapores pueden explotar si se Se deben respetar ADVERTENCIA: todas las instrucciones de seguridad al usar la unidad. Por encienden. Adopte las siguientes precauciones: favor, lea estas instrucciones antes de utilizar la unidad para garantizar la seguridad del operador y los observadores.
• • • • • • • • • • • • • • • OTRAS ADVERTENCIAS DE SEGURIDAD Utilice la herramienta apropiada. Use esta herramienta sólo para el propósito para el que fue diseñada. Sólo use la unidad como se indica en este manual. Sostenga siempre la unidad con ambas manos durante la operación. Sostenga firmemente ambas manijas o empuñaduras. No se extienda demasiado. Siempre debe estar bien afirmado y mantener el equilibrio adecuado. Tenga cuidado al trabajar sobre escalinatas, cuestas empinadas o pendientes.
• SÍMBOLOS INTERNACIONALES Y DE SEGURIDAD • Este manual del operador describe símbolos de seguridad e internacionales, así como pictogramas, que pueden aparecer en este producto. Lea el manual del operador para obtener información completa sobre seguridad, montaje, funcionamiento, mantenimiento y reparaciones. SÍMBOLOS SIGNIFICADO SÍMBOLOS SIGNIFICADO • SÍMBOLO DE ALERTA DE SEGURIDAD • APAGADO/ENCENDIDO DE CONTROL DE PARADA Indica peligro, advertencia o precaución.
CONOZCA SU UNIDAD APLICACIONES • • • Corta hierbas y malezas ligeras Bordeado Recorte decorativo alrededor de árboles, vallas, etc. Silenciador Empuñadura cuerda de arranque HERRAMIENTAS NECESARIAS PARA EL ENSAMBLAJE • Bujía de encendido Empuñadura del eje Destornillador Phillips n.
MONTAJE INSTALACIÓN DEL PROTECTOR DEL CABEZAL DE CORTE Protector del cabezal de corte ADVERTENCIA: A fin de evitar que se produzcan Ranura Soporte de montaje lesiones personales graves, no opere nunca la unidad sin el protector del cabezal de corte en su lugar. 1. Extraiga la tuerca de mariposa y la arandela del protector del cabezal de corte. 2. Inserte la lengüeta corta (la que no tiene orificio) en el soporte de montaje dentro de la ranura del protector del cabezal de corte (Fig. 1). 3.
1/8 Fig. 5 INSTALACIÓN Y AJUSTE DE LA MANIJA Manija Instalación de la manija 1. Oprima la manija hacia abajo sobre el alojamiento del eje superior (Fig. 6). Asegúrese de que el orificio del perno hexagonal mire hacia la izquierda (Fig. 6). 2. Inserte el perno en el orificio del perno hexagonal y presione para que pase a través de él (Fig. 7). Coloque la arandela en el perno (Fig. 7). Enrosque la tuerca de mariposa en el perno, pero no la ajuste completamente (Fig. 7). 3.
ACEITE Y COMBUSTIBLE INSTRUCCIONES PARA LA MEZCLA DEL ACEITE Y EL COMBUSTIBLE El uso de combustible viejo y/o mal mezclado es la causa más frecuente de los problemas de rendimiento. Sólo se debe utilizar gasolina nueva, limpia y sin plomo. Siga atentamente las instrucciones para que la mezcla de gasolina/aceite sea adecuada.
ARRANQUE Y PARADA ADVERTENCIA: Opere esta unidad únicamente en una zona bien ventilada, al aire libre. Los humos de escape de monóxido de carbono pueden ser mortales en un lugar cerrado. Interruptor encendido / apagado Apagado (O) ADVERTENCIA: Se debe evitar arrancar accidentalmente la unidad. A fin de evitar que se produzcan lesiones graves, el operador y la unidad deben estar en una posición estable cuando se jala la cuerda de arranque (Fig. 11).
INSTRUCCIONES DE PARADA 1. Suelte el control del acelerador y deje que el motor funcione en ralentí. 2. Oprima y mantenga apretado el interruptor de encendido/apagado en la posición Apagado (O) hasta que el motor se pare por completo (Fig. 8). FUNCIONAMIENTO CÓMO SOSTENER LA UNIDAD ADVERTENCIA: Utilice siempre protección ocular, auditiva, de manos, pies y corporal para reducir el riesgo de sufrir lesiones durante la operación de esta unidad.
MANTENIMIENTO ADVERTENCIA: A fin de evitar lesiones personales PROGRAMA DE MANTENIMIENTO ADVERTENCIA: Utilice vestimenta de protección y respete todas las instrucciones de seguridad para evitar que se produzcan lesiones personales graves. Realice estos procedimientos de mantenimiento requeridos con la frecuencia establecida en la tabla. Estos procedimientos también deben realizarse como parte de la afinación estacional.
Cabezal de corte Hilo Hilo Lazo Fig. 16 MANTENIMIENTO DEL FILTRO DE AIRE Filtro de aire Si no se mantiene el filtro de aire se puede obtener un rendimiento insuficiente o se pude dañar el motor de manera permanente. Las averías del motor ocasionadas por un mantenimiento inadecuado del filtro de aire no están cubiertas por la garantía del producto. Limpieza del filtro de aire 1.
MANTENIMIENTO DE LA BUJÍA 1. Detenga el motor y deje que se enfríe. Sujete con firmeza la funda de la bujía y tire para sacarla de la bujía. 2. Limpie alrededor de la bujía. Retire la bujía de la tapa del cilindro con una llave de cubo de 5/8 pulgadas, girando en sentido contrario a las agujas del reloj. ADVERTENCIA: No limpie de forma abrasiva ni raspe o limpie los electrodos de las bujías. La presencia de polvo abrasivo en el motor podría dañar el cilindro. 0.025 pulgadas (0.635 mm) 3.
SOLUCIÓN DE PROBLEMAS PROBLEMA SOLUCIÓN EL MOTOR NO ARRANCA El depósito de combustible está vacío Llene el depósito de combustible con combustible que se haya mezclado adecuadamente El bulbo del cebador no se presionó lo suficiente Oprima el bulbo del cebador 10 veces o hasta que se vea combustible El motor se ahoga Mueva la palanca del estrangulador a la Posición 3, apriete el control del acelerador y tire de la cuerda de arranque hasta que se ponga en marcha el motor El combustible está viejo (más
GARANTÍA LIMITADA DEL FABRICANTE PARA: La garantía limitada que se extiende a continuación es otorgada por la empresa Troy-Bilt LLC (Troy-Bilt) y cubre mercaderías nuevas compradas y utilizadas en los Estados Unidos, sus posesiones y territorios.