Safe Operation Practices • Set-Up • Operation • Service • Troubleshooting Operator’s Manual Self Propelled Mower Front Wheel Drive Model Series A & B IMPORTANT: READ OPERATOR'S MANUAL AND ENGINE MANUAL THOROUGHLY AND FOLLOW THE IMPORTANT SAFE OPERATION PRACTICES BEFORE OPERATING . ! STOP A 8” B B A Table of Contents Safe Operation Practices......................................... 2 Assembly & Set-Up................................................... 6 Controls & Operation..........................
1 Important Safe Operation Practices WARNING! This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol. 6. Thoroughly inspect the area where the equipment is to be used.
. Check the blade and engine mounting bolts at frequent intervals for proper tightness. Also, visually inspect blade for damage (e.g., bent, cracked, worn). Replace blade with the original equipment manufacture’s (O.E.M.) blade only, listed in this manual. “Use of parts which do not meet the original equipment specifications may lead to improper performance and compromise safety!” 4. Mower blades are sharp and can cut. Wrap the blade or wear gloves, and use extra caution when servicing them. 5.
Do not modify engine Spark Arrestor To avoid serious injury or death, do not modify engine in any way. Tampering with the governor setting can lead to a runaway engine and cause it to operate at unsafe speeds. Never tamper with factory setting of engine governor.
(OK) Figure 1 Slope Gauge e da s h e d lin 15°/25% Slope 5% 15°/2 USE THIS SLOPE GAUGE TO DETERMINE IF A SLOPE IS TOO STEEP FOR SAFE OPERATION! To check the slope, proceed as follows: 1. Remove this page and fold along the dashed line. 2. Locate a vertical object on or behind the slope (e.g. a pole, building, fence, tree, etc.) 3. Align either side of the slope gauge with the object (See Figure 1 and Figure 2 ). 4.
2 Assembly & Set-Up Thank You Thank you for purchasing this product. It was carefully engineered to provide excellent performance when properly operated and maintained. Please read this entire manual prior to operating the equipment. It instructs you how to safely and easily set up, operate and maintain your machine. Please be sure that you, and any other persons who will operate the machine, carefully follow the recommended safety practices at all times.
C 1. (a) (b) Follow steps below to assemble the grass catcher (if needed). Make certain bag is turned right side out before assembling (warning label will be on the outside). See Figure 2-8. C a. Place bag over frame so that its black plastic side is at the bottom. b. Slip plastic channel of grass bag over hooks on the frame. (b) (If Equipped) Your mower may be shipped as a mulcher.
Set-Up Drive Control (If Equipped) 2 Higher 1 3 Lower 2 Higher 1 Lower 3 High Wheel If equipped, there is an adjustment wheel located in the drive control handle housing that is used to tighten or loosen the drive belt. You will need to adjust the drive control if the mower does not propel itself with the drive control engaged or if the mower’s wheels hesitate with the drive control engaged.
3 Controls & Operation Bail Drive Control † Blade Control Recoil Starter Rear Discharge Door Grass Catcher † Deck Wash † Cutting Height Adjustment Lever Side Discharge Chute † Mulch Plug † Single Lever Drive Control † Dual Lever Drive Controls † Cutting Height Adjustment Lever Premium Drive Control † Electric Starter Push Key † † If Equipped Figure 3-1 Blade Control Bail Drive Control (If Equipped) The blade control is attached to the upper handle of the mower.
Premium Drive Control (If Equipped) Electric Starter Push Key (If Equipped) The premium drive control is located on the upper handle and is used to engage the drive. Pushing the control forward will engage the drive. The farther the control is pushed forward, the faster the mower will propel. Once pressure is released from the control it will return to the neutral position and the drive will be disengaged. The electric starter push key is located on the right side of the upper handle.
4 Service Maintenance General Recommendations • Always observe safety rules when performing any maintenance. • The warranty on this lawn mower does not cover items that have been subjected to operator abuse or negligence. To receive full value from warranty, operator must maintain the lawn mower as instructed here. • Deck Care Deck Wash (If Equipped) Clean underside of the mower deck after each use to prevent build-up of grass clippings or other debris. Follow steps below for proper cleaning.
Drive Adjustment (If Equipped with Premium Drive) The drive system consists of pulleys, a belt , and a cable linking the transmission to the drive handle. As these components wear, adjustment may be needed. To adjust the drive linkage perform the following: 1. 5. Reinsert the drive cable fitting into the upper handle and rotate it downward. 6. Start the mower and check the function of the drive handle.
2. (+) Positive Terminal (-) Negative Terminal Insert the battery charger plug into a standard 120V household outlet. Charge battery for 8 to 10 hours before initial use. Do not charge longer than 12 hours. The battery should only need to be charged upon initial setup, at the end of the season, after any other extended periods of non-use, and as needed.
5 Troubleshooting Problem Engine fails to start Engine fails to start with electric starter (Electric Start Units Only) Engine runs erratic Engine overheats Occasional skips (hesitates) at high speed 14 Cause Remedy 1. Blade control disengaged. 1. Engage blade control. 2. Spark plug boot disconnected. 2. Connect wire to spark boot. 3. Fuel tank empty or stale fuel. 3. Fill tank with clean, fresh gasoline. 4. Engine not primed (if equipped with primer). 4.
Problem Idles poorly Excessive vibration/noise Mower will not mulch grass (if equipped) Uneven cut Mower will not self propel High pullback effort Cause Remedy 1. Spark plug fouled, faulty, or gap too wide. 1. Reset gap or replace spark plug. 2. Dirty air cleaner. 2. Refer to Engine Operator’s Manual. 1. Cutting blade loose or unbalanced. 1. Tighten blade and adapter. Balance blade. 2. Bent/damaged blade or blade adapter. 2. See an authorized service dealer. 1. Wet grass. 1.
Notes 16
Medidas de seguridad • Configuración • Funcionamiento • Servicio • Solución de problemas Manual del Operador Cortadora de césped autopropulsada Transmisión de rueda delantera Modelo de la Serie A y B IMPORTANTE: LEA EL MANUAL DEL OPERADOR Y EL MANUAL DEL MOTOR A FONDO Y SIGA LAS PRÁCTICAS DE OPERACIÓN SEGURA ANTES DE OPERAR. ! STOP A 8” B B A Índice Medidas de seguridad....................................................... 2 Montaje y configuración..................................................
1 Importantes medidas de seguridad ¡ADVERTENCIA! La presencia de este símbolo indica que se trata de instrucciones de seguridad importantes que se deben respetar para evitar poner en peligro su seguridad personal y/o material y la de otras personas. Lea y cumpla todas las instrucciones de este manual antes de intentar hacer funcionar esta máquina. Si no respeta estas instrucciones puede provocar lesiones personales.
Funcionamiento en pendiente 6. Apague los cigarrillos, puros, pipas y toda otra fuente de combustión. 7. Nunca cargue combustible en la máquina en espacios cerrados porque los vapores inflamables podrían acumularse en el lugar. 8. Nunca saque el tapón de la gasolina ni agregue combustible mientras el motor está caliente o en marcha. Deje que el motor se enfríe por lo menos dos minutos antes de volver a cargar combustible. 9. Nunca llene en exceso el depósito de combustible.
15. Según la Comisión de Seguridad de Productos para el Consumidor de los Estados Unidos (CPSC) y la Agencia de Protección Ambiental de los Estados Unidos (EPA), este producto tiene una vida útil media de siete (7) años ó 140 horas de funcionamiento. Al finalizar la vida útil media haga inspeccionar anualmente esta unidad por un distribuidor de servicio autorizado para cerciorarse de que todos los sistemas mecánicos y de seguridad funcionan correctamente y no tienen excesivo desgaste.
(OK) Figura 1 Indicador de pendiente g Pendiente de 15° Línea de Figura 2 (DEMASIADO EMPINADA) 5° uio n e s a1 ¡USE ESTE INDICADOR DE PENDIENTE PARA DETERMINAR SI UNA PENDIENTE ES DEMASIADO EMPINADA PARA OPERAR CON SEGURIDAD! Para comprobar la pendiente, proceda de la siguiente manera: 1. Retire esta página y pliéguela por la línea de guiones. 2. Ubique un objeto vertical que esté sobre la pendiente o detrás de la misma (por ejemplo, un poste, un edificio, un cerco, un árbol, etc.) 3.
2 Montaje y configuración Muchas gracias Gracias por comprar este producto. Ha sido cuidadosamente diseñado para brindar excelente rendimiento si se lo hace funcionar y se lo mantiene correctamente. especificaciones de los productos, diseños y equipos sin previo aviso y sin generar responsabilidad por obligaciones de ningún tipo. Si corresponde, la información sobre las prueba de potencia utilizada para determinar la potencia nominal del motor equipado en esta máquina se puede consultar en www.opei.
Colector de césped (si está incluido) C 1. (a) (b) C Siga los pasos a continuación para ensamblar el colector de recortes de césped (si fuera necesario). Asegúrese que la bolsa para recortes está con el lado derecho hacia afuera antes de ensamblar (la etiqueta de advertencia estará hacia afuera). Consulte . a. Coloque la bolsa sobre el marco de modo que el lado de plástico negro quede en el fondo. b. Deslice el canal plástico de la bolsa sobre los ganchos en el marco.
Control de la transmisión (si está incluido) 2 Superior Higher 1 3 Inferior Lower 2 Superior Higher 1 Inferior Lower 3 Rueda alta Figura 2-12 Si está incluido, la rueda de ajuste está ubicada en el alojamiento de la manija de control de la transmisión que se utiliza para ajustar o aflojar la correa de transmisión.
3 Controles y funcionamiento Gancho de control Drive Control † de Bail la transmisión † ControlControl de las cuchillas Blade Arrancador retroceso Recoilde Starter Puerta trasera de descarga Rear Discharge Door Colector césped†† GrassdeCatcher Sistema de lavado de plataforma † Deck Wash † Cutting Height Palanca de ajuste Adjustment de la altura de corte Lever Discharge TolvaSide de descarga lateral † Chute † Clavija Mulch para abono Plug†† Control de transmisión de palanca única † Control de D
Control de la transmisión premium (si está incluido) Botón del arrancador eléctrico (si viene incluido) El control de la transmisión premium se encuentra ubicado en la manija superior y se utiliza para enganchar la transmisión. Al empujar el control hacia adelante, la transmisión quedará enganchada. Cuanto más lejos se empuje el control hacia adelante, más rápido avanzará. Cuando se libera la presión del control, éste volverá a la posición neutra y la transmisión se desenganchará.
4 Servicio Mantenimiento Recomendaciones generales • Respete siempre las reglas de seguridad al realizar tareas de mantenimiento. • La garantía de esta cortadora no cubre elementos que han estado sujetos al mal uso o la negligencia del operador. Para recibir el reembolso total de la garantía, el operador deberá mantener la cortadora como se indica en este manual. • El cambio de la velocidad controlada del motor invalidará la garantía del motor.
Ajuste de la transmisión (si incluye transmisión premium) 5. Vuelva a insertar el accesorio del cable de la transmisión en la manija superior y gírela hacia abajo. El sistema de transmisión consiste de poleas, una correa y un cable que vincula la transmisión a la manija de transmisión. Como estos componentes se gastan, es posible que sea necesario el ajuste. Para ajustar la varilla de la transmisión haga lo siguiente: 6. Arranque la cortadora y compruebe el funcionamiento de la manija de transmisión.
2. (+) (+) Terminal Positive positivo Terminal (-)Terminal (-) Negative negativo Terminal Inserte el enchufe del cargador de baterías en un tomacorriente residencial común de 120 voltios. Cargue la batería de 8 a 10 horas antes de usar la unidad por primera vez. No cargue por más de 12 horas. La batería únicamente necesitará cargarse en el ajuste inicial, al final de la temporada, luego de que no se haya utilizado por períodos prolongados de tiempo y según sea necesario.
5 Solución de problemas Problema El motor no arranca Causa Solución 1. Control de la cuchilla desenganchado. 1. Engrane el control de la cuchilla. 2. Se ha desconectado el capuchón de la bujía. 2. Conecte el cable al capuchón de la bujía. 3. El depósito de combustible está vacío o el combustible se ha echado a perder. 3. Llene el tanque con gasolina limpia y nueva. 4. El motor no está cebado (si está equipado con cebador). 4.
Problema No ralentiza bien Vibración/ruido excesivos La cortadora de césped no realiza el abono del césped (si cuenta con este equipo) Causa Solución 1. Bujía sucia, averiada o con exceso de separación. 1. Vuelva a ajustar la separación o reemplace la bujía. 2. El depurador de aire está sucio. 2. Consulte el Manual del operador del motor. 1. Cuchilla de corte floja o descentrada. 1. Apriete la cuchilla y el adaptador Equilibre la cuchilla. 2. Adaptador de cuchilla o cuchilla doblada/dañada. 2.
MTD LLC, P.O.