Operator’s Manual Straight Shaft Trimmer TBSS IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY P/N 769-02553 (5/06)
INTRODUCTION THANK YOU Thank you for buying this quality product. This modern outdoor power tool will provide many hours of useful service. You will find it to be a great labor-saving device. This operator’s manual provides you with easy-tounderstand operating instructions. Read the whole manual and follow all the instructions to keep your new outdoor power tool in top operating condition.
RULES FOR SAFE OPERATION The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and their explanations, deserve your careful attention and understanding. The safety warnings do not, by themselves, eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures. SYMBOL MEANING SAFETY ALERT SYMBOL: Indicates danger, warning, or caution. Attention is required in order to avoid serious personal injury.
RULES FOR SAFE OPERATION • CORD SETS: Make sure your cord set is in good condition. When using a cord set, be sure to use a cord that is heavy enough to carry the current that your unit will draw. An undersized cord set will cause a drop in line voltage resulting in loss of power and overheating. See the operator’s manual for the unit that will power this add-on for the recommended cord size. • Inspect all extension cords and the unit power connection periodically.
RULES FOR SAFE OPERATION SAFETY AND INTERNATIONAL SYMBOLS This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety, assembly, operating and maintenance and repair information. SYMBOL MEANING • SAFETY ALERT SYMBOL Indicates danger, warning, or caution. May be used in conjunction with other symbols or pictographs.
RULES FOR SAFE OPERATION KNOW YOUR UNIT APPLICATIONS With Trimmer Add-On: • Cutting grass and light weeds. • Decorative trimming around trees, fences, etc.
OPERATING INSTRUCTIONS ASSEMBLING THE COUPLER Release Button Coupler The following Troy-Bilt Add-Ons are also available for your unit: Blower/Vacuum . . . . . . . . . . . . . . . . . . . . . . . . . . . TBBV Cultivator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBGC Hedge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . TBHS Edger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBLE Snow Thrower . . . . . . . . . . . . . . . . . . . . . . . . . . .
OPERATING INSTRUCTIONS HOLDING THE TRIMMER WARNING: Always wear eye, hearing, foot and body protection to reduce the risk of injury when operating this unit. Before operating the unit, stand in the operating position (Figs. 4 & 5). Check for the following: • The operator is wearing eye protection and proper clothing. • The right arm is slightly bent, and the hand is holding the shaft grip. NOTE: Do not rest the Bump Head™ on the ground while the unit is running.
MAINTENANCE AND REPAIR INSTRUCTIONS LINE INSTALLATION FOR THE SPEEDSPOOL® Always use Genuine Factory Parts™ 0.080 inch (2.03 mm) replacement line. Line other than specified may make the engine overheat or fail. WARNING: Never use metal-reinforced line, wire, or rope, etc. These can break off and become a dangerous projectile. Trimming Line Eyelet There are two methods to replace the SpeedSpool® trimming line.
MAINTENANCE AND REPAIR INSTRUCTIONS 7. Repeat procedures 4-6 with the second piece of line. 8. Hold the outer spool. Wind the inner reel counterclockwise until approximately four (4) inches (102 mm) of line remain (Fig. 12). NOTE: Do not wind the inner reel before installing the second piece of line. 2. Pull the old inner reel with existing line from the outer spool. 3. Insert the ends of the prewound inner reel line into the outer spool eyelets (Fig. 15).
MAINTENANCE AND REPAIR INSTRUCTIONS 2. Pull out the bump knob, spring, and foam seal (Fig. 14). 3. Pull the inner reel with existing line from the outer spool (Fig. 14). 4. Remove any existing line from the inner reel before cleaning. Remove any debris or grass from the knob, spring, inner reel, and foam seal. Wash the inner reel with warm soapy water (Fig. 17). CLEANING Use a small brush to clean off the outside of the unit. Do not use strong detergents.
TROUBLESHOOTING CUTTING HEAD WILL NOT ADVANCE LINE CAUSE ACTION Cutting head bound with grass Stop the unit and clean cutting attachment Cutting head out of line Refill with new line Inner reel bound up Replace the inner reel Cutting head dirty Clean inner reel and outer spool Line welded Disassemble, remove the welded section and rewind the line Line twisted when refilled Disassemble and rewind the line Not enough line is exposed Push the bump knob and pull out line until 4 inches (102 mm) o
SPECIFICATIONS STRAIGHT SHAFT TRIMMER ADD-ON Unit Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 lbs. (1.36 kg.) Cutting Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SpeedSpool® Dual String Cutting Head Line Spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NOTES 14
NOTES 15
MANUFACTURER’S LIMITED WARRANTY FOR: The limited warranty set forth below is given by Troy-Bilt LLC (“Troy-Bilt”) with respect with new merchandise purchased and used in the United States, its possessions and territories. Troy-Bilt warrants this product against defects in material and workmanship for a period of two (2) years commencing on the date of original purchase and will, at its option, repair or replace, free of charge, any part found to be defective in material or workmanship.
Manuel de L'utilisateur Désherbeuse à arbre droit TBSS IMPORTANT: LISEZ LES RÈGLES ET CONSIGNES DE SÉCURITÉ SOIGNEUSEMENT P/N 769-02553 (5/06)
INTRODUCTION TOUS NOS REMERCIEMENTS Nous vous remercions d'avoir acheté ce produit de qualité. Cet outil moderne de plein air est conçu pour vous rendre service pendant longtemps. Il vous sauvera beaucoup de temps comme vous pourrez vous en rendre compte. Ce manuel de l'utilisateur comporte un mode d'emploi facile à comprendre. Prenez soin de le lire au complet et de respecter toutes les instructions pour conserver votre outil en excellant état de fonctionnement.
CONSIGNES DE SÉCURITÉ Les symboles de sécurité attirent votre attention sur des dangers potentiels. Ces symboles et leurs détails explicatifs méritent que vous les lisiez et compreniez bien. Les avertissements de sécurité ne peuvent éviter les dangers de par eux-mêmes. Les consignes ou mises en garde qu'ils donnent ne remplacent pas des mesures préventives appropriées contre les accidents. SYMBOLE SIGNIFICATION SYMBOLE D’ALERTE DE SÉCURITÉ : indique un danger, un avertissement ou une mise en garde.
CONSIGNES DE SÉCURITÉ • Inspectez souvent les rallonges et la connexion d’alimentation. Relevez tout signe de détérioration, coupures ou fissures dans l’isolation. Vérifiez que les connexions ne sont ni endommagées ni défectueuses, et remplacez les cordons le cas échéant.
CONSIGNES DE SÉCURITÉ SYMBOLES DE SÉCURITÉ ET INTERNATIONAUX Ce manuel de l'utilisateur décrit les symboles et pictogrammes de sécurité et internationaux pouvant apparaître sur ce produit. Consultez le manuel de l'utilisateur pour les informations concernant la sécurité, le montage, le fonctionnement, l'entretien et les réparations. SYMBOLE SIGNIFICATION • SYMBOLE D’ALERTE DE SÉCURITÉ Indique un danger, un avertissement ou une mise en garde.
CONSIGNES DE SÉCURITÉ FAMILIARISEZ-VOUS AVEC VOTRE APPAREIL APPLICATIONS Avec l'accessoire à désherber : • Coupe d'herbe et de mauvaises herbes légères. • Taille autour des arbres, des clôtures, etc.
MODE D'EMPLOI MONTAGE DU COUPLEUR Les accessoires Troy-Bilt suivants sont également disponibles pour votre appareil : Souffleuse/aspirateur . . . . . . . . . . . . . . . . . . . . . . . TBBV Cultivateur . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBGC Taille-haies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBHS Coupe-bordure . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBLE Souffleuse à neige . . . . . . . . . . . . . . . . . . . . . . . . . .
MODE D'EMPLOI Le fil peut se briser dans les cas suivants : TENUE DE LA DÉSHERBEUSE AVERTISSEMENT: portez toujours des protections (yeux, oreilles, pieds et corps) pour diminuer les risques de blessures durant l'utilisation de l'appareil. • Happement de corps étrangers • Usure normale du fil • Coupe de mauvaises herbes épaisses à longues tiges Avant de faire marcher l'appareil, tenez-vous en position de fonctionnement (Figs. 4 et 5).
ENTRETIEN ET RÉPARATIONS INSTALLATION DU FIL DU SPEEDSPOOLMD Utilisez toujours une ligne de remplacement Genuine Factory PartsMC de 2,03 mm (0,080 po). Tout autre ligne peut faire surchauffer ou entraîner une panne du moteur. Fil Œillet AVERTISSEMENT : n'utilisez jamais de fil, de chaîne ou de cordon à renfort métallique car ils peuvent se briser et se transformer en projectile dangereux.
ENTRETIEN ET RÉPARATIONS 7. Répétez les procédures 4-6 pour le second morceau de fil. 8. Tenez la bobine extérieure. Rembobinez le moulinet intérieur vers la gauche jusqu'à ce qu'il ne reste plus qu'environ 102 mm (4 po) de fil (Fig. 12). REMARQUE : ne rembobinez pas le moulinet intérieur avant de poser le second fil. Installation d'un moulinet pré-enroulé 1. Retirez le bouton de butée, le ressort et le joint en mousse en tournant le bouton de butée à gauche (Fig. 14).
ENTRETIEN ET RÉPARATIONS MD Nettoyage du SpeedSpool Le nettoyage du SpeedSpoolMD peut s'avérer nécessaire • pour retirer du fil coincé ou trop long; • si le SpeedSpool devient difficile à rembobiner ou s'il ne fonctionne pas correctement lorsque vous tapez sa tête sur le sol. 1. Axe MD Plongeur Tenez la bobine extérieure et dévissez le bouton de butée à gauche (Fig. 16). Moulinet intérieur Fig. 18 PIÈCES DE RECHANGE SPEEDSPOOLMD Fil de remplacement . . . . . . . . . . . . . . . . . . . . . . . .
DÉPANNAGE LA TÊTE DE COUPE NE FAIT PAS AVANCER LE FIL CAUSE SOLUTION Accessoire de coupe engorgé d'herbes Arrêtez et débranchez l’appareil et nettoyez l'accessoire de coupe Tête de coupe sans fil Chargez du fil neuf Moulinet intérieur bloqué Remplacez le moulinet Tête de coupe sale Nettoyez le moulinet intérieur et la bobine extérieure Fil soudé Démontez et déposez la partie soudée, et rembobinez le fil Fil tordu durant la recharge Démontez puis rembobinez le fil Quantité de fil exposée insuff
CARACTÉRISTIQUES ACCESSOIRE DE DÉSHERBEUSE À ARBRE DROIT Poids de l’appareil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,36 kg (3 lb) Mécanisme de coupe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tête de coupe à deux fils SpeedSpoolMD Bobine de fil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMARQUE F14
REMARQUE F15
GARANTIE LIMITÉE DU FABRICANT POUR: La garantie limitée énoncée ci-après est accordée par Troy-Bilt LLC (« Troy-Bilt ») et concerne les marchandises neuves achetées et utilisées aux États-Unis, ainsi que dans leurs possessions et territoires.
Manual Del Operador Recortador de eje recto TBSS IMPORTANTE: LEA LAS REGLAS DE SEGURIDAD E INSTRUCCIONES DETENIDAMENTE P/N 769-02553 (5/06)
INTRODUCCION MUCHAS GRACIAS Gracias por haber adquirido este gran producto. Esta moderna herramienta motriz de exteriores está diseñada para brindarle muchas horas de servicio útil. Usted comprobará que es un artefacto que le ahorrará mucho trabajo. Este manual del operador le brinda instrucciones de operación de fácil comprensión. Lea todo el manual y siga todas las instrucciones para mantener su nueva herramienta motriz de exteriores en las mejores condiciones de funcionamiento.
NORMAS PARA UNA OPERACION SEGURA Los símbolos de seguridad se utilizan para llamar su atención sobre posibles peligros. Los símbolos de seguridad y sus explicaciones merecen toda su atención y comprensión. Los símbolos de seguridad no eliminan ningún peligro por sí mismos. Las instrucciones o advertencias que ofrecen no substituyen las medidas adecuadas de prevención de accidentes. SIMBOLO SIGNIFICADO SIMBOLO DE ALERTA DE SEGURIDAD: Indica peligro, advertencia o precaución.
NORMAS PARA UNA OPERACION SEGURA • JUEGOS DE CABLES: Verifique que su juego de cable esté en buenas condiciones. Cuando use un juego de cables, verifique que el cable que usa es lo suficientemente pesado como para conducir la corriente que su unidad consumirá. Un juego de cables de menor peso puede causar una caída de voltaje en la línea y llevar a una pérdida de energía y recalentamiento.
NORMAS PARA UNA OPERACION SEGURA SIMBOLOS DE SEGURIDAD E INTERNACIONALES Este manual del operador describe los símbolos y figuras de seguridad e internacionales que pueden aparecer en este producto. Lea el manual del operador para obtener información completa acerca de la seguridad, ensamble, operación y mantenimiento y reparación. SIMBOLO SIGNIFICADO • SIMBOLO DE ALERTA DE SEGURIDAD Indica peligro, advertencia o precaución. Puede ser utilizado junto con otros símbolos o figuras.
NORMAS PARA UNA OPERACION SEGURA CONOZCA SU UNIDAD APLICACIONES Con aditamento para recortador de eje: • Corte de césped y malezas delgadas. • Recorte decorativo alrededor de árboles, cercos, etc.
INSTRUCCIONES DE OPERACIÓN Acoplador ENSAMBLAJE DEL ACOPLADOR Los siguientes accesorios Troy-Bilt también están disponibles para su unidad: Soplador/Aspirador . . . . . . . . . . . . . . . . . . . . . . . . . TBBV Cultivador . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBGC Recortador de setos . . . . . . . . . . . . . . . . . . . . . . . . TBHS Recortador de bordes . . . . . . . . . . . . . . . . . . . . . . . TBLE Soplador de nieve . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTRUCCIONES DE OPERACIÓN COMO SOSTENER EL RECORTADOR ADVERTENCIA: Use siempre protección para sus ojos, audición, pies y cuerpo para reducir el riesgo de una lesión al operar esta unidad. La línea puede cortarse por: • Enredarse con un objeto extraño • Fatiga normal de la línea • Intentar cortar hierbas gruesas y leñosas Antes de operar esta unidad, párese en posición de operación (Figs. 4 y 5). Verifique lo siguiente: • Forzar la línea en objetos como paredes o postes de cercos.
INSTRUCCIONES DE MANTENIMIENTO Y REPARACION INSTALACIÓN DE LA LINEA PARA EL SPEEDSPOOL® Use siempre línea de reemplazo de 2,03 mm (0,080 pulgadas) de Genuine Factory Parts™. Una línea diferente a la especificada pudiera recalentar el motor o hacer que falle. Línea de corte Ojalillo ADVERTENCIA: No use nunca línea reforzada con metal, alambre, cadena ni soga, etc. Estos elementos pueden desprenderse y convertirse en un proyectil peligroso. Existen dos métodos para cambiar la línea de corte SpeedSpool®.
INSTRUCCIONES DE MANTENIMIENTO Y REPARACION 7. Repita los pasos 4 a 6 con la segunda pieza de línea. Instalación de un carrete interior prebobinado 8. Sostenga la bobina exterior. Bobine el carrete interior en sentido antihorario hasta que queden alrededor de cuatro (4) pulgadas (102 mm.) de línea (Fig. 12). 1. Saque la perilla percuisva, el resorte y el sello de espuma girando la perilla percusiva en sentido antihorario (Fig. 14).
INSTRUCCIONES DE MANTENIMIENTO Y REPARACION Limpieza del SpeedSpool® La limpieza de SpeedSpool® puede ser necesaria, • Para sacar línea enredada o en exceso, • Si el bobinado del SpeedSpool® se torna dificultoso o no opera en forma correcta cuando golpea la cabeza contra el suelo, 1. Sostenga la bobina exterior y desenrosque la perilla percusiva en sentido antihorario (Fig. 16). Carrete interior PIEZAS DE REPUESTO PARA EL SPEEDSPOOL® Línea de repuesto . . . . . . . . . . . . . . . . . . . . . . . .
RESOLUCION DE PROBLEMAS LA CABEZA DE CORTE NO HACE AVANZAR LINEA CAUSA ACCION El accesorio de corte está atascado de hierba Apague, desenchufe la unidad y limpie el accesorio de corte El accesorio de corte no tiene línea Coloque una línea nueva El carrete interior está trabado Cambie el carrete interior La cabeza de corte está sucia Limpie el carrete interior y la bobina exterior La línea se ha soldado Desarme, saque la sección soldada y rebobine la línea La línea se retorció al reponerla Desar
ESPECIFICACIONES ACCESORIO RECORTADOR DE EJE RECTO Peso de la unidad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 lbs. (1.36 kg.) Mecanismo de corte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SpeedSpool® Cabeza percusiva de línea doble Bobina de la línea . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NOTAS E14
BOOM AND TRIMMER PARTS - MODEL TBSS STRAIGHT SHAFT TRIMMER ATTACHMENT 3 1 2 6 5 4 8 7 5 Item Part No.
GARANTÍA LIMITADA DEL FABRICANTE PARA: La garantía limitada establecida a continuación es dada por Troy-Bilt LLC (“Troy-Bilt”) con respecto a mercancía nueva que sea comprada y usada en los Estados Unidos, sus posesiones y territorios.