Installation Sheet

1
2
6
7
13
8
5
9
4
3
11
10
12
CATE
F1007
INSTALLATION INSTRUCTIONS
FIXTURE INSTALLATION
1. Thread the 2 MOUNTING SCREWS (2) into the MOUNTING PLATE (1).( the green screw is in the front ). Attach the
mounting ring to the junction box. Then thread the nipple into the MOUNTING PLATE (1) and the hex nut onto the
nipple.
2. Remove the threaded ring from the SCREW COLLAR LOOP (3). Fully thread the SCREW COLLAR LOOP (3) onto
the nipple. Place the CANOPY (4) over the screw collar loop and against the ceiling. Adjust the nipple so that
1
4
" of
threads on the screw collar loop extend beyond the canopy. Then remove the canopy and tighten the hex nut against
the mounting plate.
3. Open the LOCK LINKS (5) and attach to the screw collar loop. Close the top LOCK LINK (5).Hang the fixture on the
chain at the desired height. Remove excess chain. Close the bottom LOCK LINK on fixture LOOP (6).Unscrew the
ring from the screw collar loop. Let the ring and canopy slide down the chain to the top of the fixture.Thread the lead
wires and ground wire (first) through chain,ring and then the canopy.
4. When the ceiling is reached,measure 6" beyond the chain and cut off the excess wire. Separate the leads and strip of
approx.
1
2
" of insulation from each lead.Twist the strands of wire together. Push the leads and ground wire up through
the screw collar loop and nipple and into the junction box.
5. Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bar copper wire) or the
GROUND SCREW (7) on the MOUNTING PLATE (1). NEVER CONNECT GROUND WIRE TO "HOT" WIRE!
FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
6. Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together with an
approved fastener (WIRE NUTS) (8). Starting 1" below the fastener, tightly wrap the connection with electrical tape
so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRE OF
STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!
7. Connect the black fixture leads to the hot (Generally black) wire in the outlet box. Fasten the joined wires same as
previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT
IN SERIOUS INJURY OR DEATH!
8. Slide the CANOPY (4) and screw collar ring up the chain and secure the canopy to the ceiling.
9. Put the NIPPLE (9) , POLE (10) onto FIXTURE and TWIST with LOOP (11). Put CANDLE SLEEVES (12) onto
CANDLE CUPS (8), adjust it on straight.
10. Push the BULBS (13) (not included) up into the sockets of the fixture.THIS FIXTURE IS RATED FOR 60 WATT
TYPE B LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE!
11. Restore power to the outlet at the breaker or fuse box.
WARNING/CAUTION
· DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS
COMPLETELY BEFORE STARTING INSTALLATION.
· TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL
APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND
MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED
FACTORY TRAINED TECHNICIAN.
· CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF
CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH
HANDS AFTER USE.
· REMOVE THE FIXTURE, PARTS AND PARTS BAG(S) FROM THE CARTON. BEFORE DISCARDING THE
CARTON, DOUBLE CHECK TO MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE
PRIOR TO INSTALLATION FOR ANY DAMAGE TO THE FIXTURE.
· DIMMING: THE FIXTURE CAN BE CONTROLLED BY A WALL DIMMING DEVICE. ONLY USE
TRIAC/ELECTRONIC DIMMER. MAKE SURE THE CARTON IS MARKED FOR USE WITH LED COMPACT
FLUORESCENT-INCANDESCENT LIGHT SOURCE ONLY. THESE CAN BE PROVIDED BY YOUR LOCAL
ELECTRICAL DISTRIBUTOR, HOME CENTER, OR HARDWARE STORE.
· PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS
www.hvlgroup.com
Questions? We're here to help!
Contact us at [e-mail]
ITEM DESCRIPTION
PART NUMBER
1
MOUNTING PLATE
HDW-F1007
2
MOUNTING SCREW
HDW-F1007
3
SCREW COLLAR LOOP
HDW-F1007
4
CANOPY CPY-F1007
5
LOCK LINKS
LNK-F1007
6
GROUND SCREW
HDW-F1007
7
WIRE NUTS
HDW-F1007
8
CANDLE CUPS CDL-F1007
9
NIPPLE HDW-F1007
10
POLE
HRD-F1007
11
LOOP LOO-F1007
12
CANDLE SLEEVES CDL-F1007-S
13
BULBS NOT INCLUDED