Installation Sheet

1
2
6
7
8
5
9
4
3
10
12
11
CATE
F1018
INSTALLATION INSTRUCTIONS
FIXTURE INSTALLATION
1. Thread the 2 MOUNTING SCREWS (2) into the MOUNTING PLATE (1).( the green screw is in the front ). Attach the
mounting ring to the junction box. Then thread the nipple into the MOUNTING PLATE (1) and the hex nut onto the
nipple.
2. Remove the threaded ring from the SCREW COLLAR LOOP (3). Fully thread the SCREW COLLAR LOOP (3) onto
the nipple. Place the CANOPY (4) over the screw collar loop and against the ceiling. Adjust the nipple so that
1
4
" of
threads on the screw collar loop extend beyond the canopy. Then remove the canopy and tighten the hex nut against
the mounting plate.
3. Open the LOCK LINKS (5) and attach to the screw collar loop. Close the top LOCK LINK (5).Hang the fixture on the
chain at the desired height. Remove excess chain. Close the bottom LOCK LINK on fixture LOOP (6).Unscrew the
ring from the screw collar loop. Let the ring and canopy slide down the chain to the top of the fixture.Thread the lead
wires and ground wire (first) through chain,ring and then the canopy.
4. When the ceiling is reached,measure 6" beyond the chain and cut off the excess wire. Separate the leads and strip of
approx.
1
2
" of insulation from each lead.Twist the strands of wire together. Push the leads and ground wire up through
the screw collar loop and nipple and into the junction box.
5. Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bar copper wire) or the
GROUND SCREW (7) on the MOUNTING PLATE (1). NEVER CONNECT GROUND WIRE TO "HOT" WIRE!
FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
6. Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together with an
approved fastener (WIRE NUTS) (8). Starting 1" below the fastener, tightly wrap the connection with electrical tape
so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRE OF
STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!
7. Connect the black fixture leads to the hot (Generally black) wire in the outlet box. Fasten the joined wires same as
previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT
IN SERIOUS INJURY OR DEATH!
8. Slide the CANOPY (4) and screw collar ring up the chain and secure the canopy to the ceiling.
9. TWIS the LOOP (10) onto NIPPLE (9). Put CANDLE SLEEVES (11) onto CANDLE CUPS (8), adjust it on straight.
10. Push the BULBS (12) (not included) up into the sockets of the fixture.THIS FIXTURE IS RATED FOR 40 WATT
TYPE B LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE!
11. Restore power to the outlet at the breaker or fuse box.
www.hvlgroup.com
Questions? We're here to help!
Contact us at [e-mail]
ITEM DESCRIPTION
PART NUMBER
1
MOUNTING PLATE
HDW-F1018
2
MOUNTING SCREW
HDW-F1018
3
SCREW COLLAR LOOP
HDW-F1018
4
CANOPY CPY-F1018
5
LOCK LINKS
LNK-F1018
6
GROUND SCREW
HDW-F1018
7
WIRE NUTS
HDW-F1018
8
CANDLE CUPS CDL-F1018
9
NIPPLE HDW-F1018
10
LOOP LOO-F1018
11
CANDLE SLEEVES CDL-F1018-S
12
BULBS NOT INCLUDED
ATTENTION PRUDENCE
· DÉBRANCHEZ L'ALIMENTATION AVANT DE REMPLIR OU DE CÂBLER LE LUMINAIRE. LISEZ
COMPLÈTEMENT TOUTES LES INSTRUCTIONS AVANT DE COMMENCER L'INSTALLATION
· POUR ÉVITER LE RISQUE D'INCENDIE OU D'ÉLECTROCUTION, LE LUMINAIRE DOIT ÊTRE INSTALLÉ
CONFORMÉMENT À TOUS LES CODES ÉLECTRIQUES/DE CONSTRUCTION NATIONAUX ET LOCAUX
APPLICABLES. L'INSTALLATION ET L'ENTRETIEN DE CET APPAREIL DOIVENT ÊTRE EFFECTUÉS PAR UN
ÉLECTRICIEN AGRÉÉ OU UN TECHNICIEN CERTIFIÉ FORMÉ EN USINE.
· CALIFORNIE PROP 65 : CET APPAREIL D'ÉCLAIRAGE CONTIENT DES PRODUITS CHIMIQUES CONNUS PAR
L'ÉTAT DE CALIFORNIE POUR PROVOQUER LE CANCER, DES MALADIES CONGÉNITALES ET/OU D'AUTRES
DOMMAGES À LA REPRODUCTION. LAVER LES MAINS APRÈS UTILISATION.
· RETIRER LE LUMINAIRE, LES PIÈCES ET LE(S) SAC(S) DE PIÈCES DU CARTON. AVANT DE JETER LE
CARTON, VÉRIFIEZ DOUBLE POUR VOUS ASSURER QUE TOUTES LES PIÈCES SONT TROUVÉES.
INSPECTER LE LUMINAIRE AVANT L'INSTALLATION POUR TOUT DOMMAGE AU LUMINAIRE.
· GRADATION : LE LUMINAIRE PEUT ÊTRE CONTRLÉ PAR UN DISPOSITIF DE GRADATION MURALE. UTILISER
UNIQUEMENT UN GRADATEUR TRIAC/ÉLECTRONIQUE. ASSUREZ-VOUS QUE LE CARTON EST MARQUÉ
POUR UNE UTILISATION AVEC UNE SOURCE DE LUMIÈRE FLUORESCENTE À INCANDESCENTE COMPACTE
UNIQUEMENT. CEUX-CI PEUVENT ÊTRE FOURNIS PAR VOTRE DISTRIBUTEUR ÉLECTRIQUE LOCAL,
CENTRE À DOMICILE OU MAGASIN DE QUINCAILLERIE.
· VEUILLEZ NETTOYER UNIQUEMENT AVEC UN CHIFFON DOUX ET SEC ! N'UTILISEZ PAS DE NETTOYANTS