Installation Sheet

FIXTURE INSTALLATION
1. Attach the ARMS (1) to the FIXTURE ASSEMBLY (2) then hang to the DISTRIBUTOR (3). Feed the wire through the
STEM (4) and twist tightly onto the DISTRIBUTOR (3). Keep adding additional stems until your desired hanging height is
met.
2. Slide in CANOPY(5 ) onto the STEM (4), and thread the SWIVEL (6) onto the top end of the STEM (4). Then attach the
SWIVEL BLOCK (7) onto the CANOPY (5), secure using HEX NUTS (8).
3. Pull the wire out from the junction box, and install the MOUNTING PLATE (9) onto the junction box using the
MOUNTING SCREWS (10).
This fixture is designed to be mounted on standard round or octagon junction box. The
junction box must be securely mounted to the structure of the building. Thread the STUDS (11) unto the MOUNTING
PLATE (9), adjust its threads so that 3/16" of threads extend beyond the CANOPY (5).
4. Attach the SAFETY CABLE (12) to the building structure or brace using CABLE CLIP (13).
5. Trim off the excess wire to a minimum 6" beyond the STEM and strip each wire 5/8".
6. Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bare copper wire) or the
GROUND SCREW (14) on the MOUNTING PLATE (9). NEVER CONNECT GROUND WIRE TO "HOT" WIRE!
FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
7. Connect the fixture's SPT Neutral (SPT WIRE WITH NO WRITINGS) wire lead to the neutral (Generally white) wire in the
outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (15). Starting 1" below the fastener, tightly
wrap the connection with electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE
NO EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!
8. Connect the fixture's SPT hot (SPT WITH WRITNGS) wire lead to the hot (Generally black) wire in the junction box.
Fasten the joined wires same as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO
FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
9. Push the wires back into the junction box. Lift up the CANOPY (5) up to the ceiling, and secure with the MOUNTING
NUTS (16)
10. Screw the BULB (17) into the socket of the fixture.THIS FIXTURE IS RATED FOR 60 WATT LAMP. DO NOT EXCEED
THE RECOMMENDED WATTAGE!
11. Restore power to the outlet at the breaker or fuse box.
CECILIA
F2608
INSTALLATION INSTRUCTIONS
WARNING/CAUTION
· DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS
COMPLETELY BEFORE STARTING INSTALLATION.
· TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL
APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND
MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED
FACTORY TRAINED TECHNICIAN.
· CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF
CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH
HANDS AFTER USE.
· REMOVE THE FIXTURE, PARTS AND PARTS BAG(S) FROM THE CARTON. BEFORE DISCARDING THE
CARTON, DOUBLE CHECK TO MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE
PRIOR TO INSTALLATION FOR ANY DAMAGE TO THE FIXTURE.
· DIMMING: THE FIXTURE CAN BE CONTROLLED BY A WALL DIMMING DEVICE. ONLY USE
TRIAC/ELECTRONIC DIMMER. MAKE SURE THE CARTON IS MARKED FOR USE WITH LED COMPACT
FLUORESCENT-INCANDESCENT LIGHT SOURCE ONLY. THESE CAN BE PROVIDED BY YOUR LOCAL
ELECTRICAL DISTRIBUTOR, HOME CENTER, OR HARDWARE STORE.
· PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS
www.hvlgroup.com
Questions? We're here to help!
Contact us at [e-mail]
1
2
3
4
7
5
8
6
9
10
11
14
15
16
13
12
17
ITEM DESCRIPTION
PART NUMBER
1 ARM ROD-F2603
2 FIXTURE ASSEMBLY FAS-F2608
3
DISTRIBUTOR MIS-F2603
4 5/8" DIA STEM KIT 6"+12"+12"+18"
STM-F2603-06,12,18
5
CANOPY CPY-F2603
6
SWIVEL SWL-F2603
7
SWIVEL BLOCK
SWL-F2603-B
8 HEX NUT NUT-F2603-H
9
MOUNTING PLATE
HDW-F2603
10
MOUNTING SCREW SCR-F2603-M
11 STUD STD-F2603
12 SAFETY CABLE CBL-F2608-S
13
CABLE CLIP CBL-F2608-C
14 GROUND SCREW SCR-F2603-G
15 WIRE NUT NUT-F2603-W
16
MOUNTING NUT
NUT-F2603-M
17
BULB
NOT INCLUDED