Installation Sheet

ManualsBrandsTroy Lighting ManualsLightingMurphy 1-Light Vintage Iron Pendant

FIXTURE PREPARATION

1. Remove the fixture and parts bag(s) from the carton.

NOTICE:

Before discarding the carton,

double check to make certain that all parts are found.

F4904 MURPHY 1-LT. SMALL PENDANT INSTALLATION INSTRUCTIONS

WARNING

DISCONNECT POWER BEFORE RELAMPING OR WIRING THE FIXTURE

READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.

CAUTION

· TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH

ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES.

· INSTALLATION AND MAINTENANCE OF THIS UNIT REQUIRES AN ELECTRICIAN OR

CERTIFIED FACTORY TRAINED TECHNICIAN.

· If an existing fixture is being replaced, remove it and note to which of the wires in the outlet box the fixture was attached.

DO NOT SEPARATE ANY OTHER WIRES THAT MAY BE IN THE BOX. DO NOT DAMAGE THE INSULATION OF OLDER WIRING.

In regular circumstances the BLACK wire will be the "Hot" lead and the WHITE wire will be the "Neutral" or "Common" lead. The

GREEN or BARE COPPER wire is the "Ground". In older buildings it is always good practice to reconfirm the polarity of the wiring.

Page 1 of 3

NOTICE

· The important safeguards and instructions outlined on this sheet cannot cover all possible conditions and situations that

may occur. It must be understood that common sense, caution and care factors that cannot be built into any product. Caution

and care must be supplied by the person(s) installing, operating and caring of this lighting fixture.

· This fixture is design to be mounted on a correctly installed standard round or octagon box or a through wiring box with a

plaster frame. The box must be securely mounted to the structure of the building. The crossbar and hardware supplied should

be used. Directly mounting the fixture to the outlet box may make it impossible to correctly align the fixture.

FIGURE-1

TROY LIGHTING

FIXTURE INSTALLATION

1. Attach the crossbar to the junction box using th mounting screws.

(The green screw should face the floor).

2. Affix the canopy to the wood canopy using the three (3) wood screws.

Insert wire to the fixtures as shown in FIGURE-1.

3. Remove the threaded ring from the collar loop. Fully thread the

collar loop onto the nipple. Thread the hex nut onto the nipple and the

nipple into the crossbar. Place the canopies over the collar loop and against

the ceiling. Adjust the nipple so that 1/4" of the threads on the collar loop

extend beyond the canopies. Tighten the hex nut against the crossbar.

Using the threaded ring, install the canopies.

4. Open the end links of the chain and attach the chain to the collar loop.

Hang the fixture on the chain at the desired height. Remove the excess chain

and close all links, then attach the chain link to the collar loop.

Unscrew the threaded ring from the collar loop. Allow the

ring and canopies to slide down the chain to the top of the fixture.

CROSSBAR

WOOD CANOPY

CANOPY

WOOD SCREW

JUNCTION BOX

COLLAR LOOP

CHAIN LINK

OVAL CHAIN

GREEN SCREWMOUNTING SCREW

NIPPLE

HEX NUT

RING

WIRE

Summary of content (3 pages)

PAGE 1
F4904 MURPHY 1-LT. SMALL PENDANT INSTALLATION INSTRUCTIONS TROY LIGHTING WARNING DISCONNECT POWER BEFORE RELAMPING OR WIRING THE FIXTURE READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION. CAUTION · TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. · INSTALLATION AND MAINTENANCE OF THIS UNIT REQUIRES AN ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
PAGE 2
WARNING The use of chain pliers for opening and closing links of chain is required. The use of tools other than chain pliers may damage the chain link resulting in a failure which can cause harm to the fixture, property, and/or person(s). Electrical tape 5. Thread the lead wire and ground wire (first) through the threaded ring, then the canopies and up through alternating links of the chain until the ceiling is reached. 6.
PAGE 3
WOOD COVER ACORN CUP SCREW SOCKET COVER LAMP GLASS PENDANT FIGURE-3 Page 3 of 3 111215ACG