Installation Sheet

ManualsBrandsTroy Lighting ManualsLighting24" Wide Single Light Integrated LED Single Pendant

FIXTURE PREPARATION

1. Remove the fixture, parts and parts bag(s) from the carton.

NOTICE:

· Before discarding the carton, double check to

make certain that all parts are found.

F5511 APOGEE 24"DIA 1LT PENDANT INSTALLATION INSTRUCTIONS

WARNING

DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE

READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.

Page 1 of 6

FIXTURE INSTALLATION

1. Attach the heavy duty strap to the outlet box.

NOTICE:

THIS LUMINAIRE MUST BE MOUNTED OR

SUPPORTED INDEPENDENTLY OF AN OUTLET BOX.

NOTICE

· The important safeguards and instructions outlined on this sheet cannot cover all possible conditions and situations that

may occur. it must be understood that common sense, caution and care factors that cannot be built into any product.

Caution and care must be supplied by the person(s) installing, operating and caring of this lighting fixture.

· This fixture is designed to be mounted on a correctly installed standard round or octagon box or a through wiring box

with a plaster frame. The box must be securely mounted to the structure of the building. The heavy duty strap and hardware

supplied should be used. directly mounting the fixture to the outlet box may make it impossible to correctly align the fixture.

· This fixture is supplied with with a 4-pcs. stem. There is one 6" section, two 12" section and one 18" section.

This feature allows the fixture to be mounted with a stem up to 48" in length in 6" increments.

· This fixture is supplied with a swivel. By rotating the canopy the fixture may be mounted to angled ceiling.

FIGURE-1

CAUTION

· TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH

ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES.

· INSTALLATION AND MAINTENANCE OF THIS UNIT REQUIRES AN ELECTRICIAN OR

CERTIFIED FACTORY TRAINED TECHNICIAN.

· If an existing fixture is being replaced, remove it and note to which of the wires in the outlet box the fixture was attached.

DO NOT SEPARATE ANY OTHER WIRES THAT MAY BE IN THE BOX. DO NOT DAMAGE THE INSULATION OF OLDER

WIRING. In regular circumstances the BLACK wire will be the "Hot" lead and the WHITE wire will be the "Neutral" or "Common"

lead. In older buildings it is always good practice to reconfirm the polarity of the wiring.

TROY LIGHTING

Canopy

Adjustable stem

Ceiling

Swivel

Outlet box

Swivel Blocker

Small Hex Nut

Heavy duty Strap

Ball Nut

Stud

2. Determine the overall desired length of the fixture. Tape

the end of the leads to a stiff wire (coat hanger) to aid in

pulling them through the stems. Place the canopy onto

the stem. Assemble the top stem section, decorative

breaker, fixture stem and swivel. Place the swivel block

over the stem connector of the canopy and thread the

hex nuts onto them.

Summary of content (6 pages)

PAGE 1
TROY LIGHTING F5511 APOGEE 24"DIA 1LT PENDANT INSTALLATION INSTRUCTIONS WARNING DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION. CAUTION · TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. · INSTALLATION AND MAINTENANCE OF THIS UNIT REQUIRES AN ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
PAGE 2
3. Thread the studs into the heavy duty strap at the spacing that matches the mounting holes in the canopy. Adjust the screw so they extend 3/16'' beyond the canopy. 4. Cut off the excess fixture wire 6'' beyond the canopy. Strip 1/2'' of insulation from the ends of the wire. Twist the wire stands together. 5. Fasten the white fixture lead of the LED Light to the white wire in the outlet box. Fasten the wires together with an approved fastener (wire nut).
PAGE 3
Adjustable stem Glass cover Fitter A Fitter B Glass holder LED socket GLASS DIFFUSER NOTE*** Please handle the glass diffuser with care when putting to the glass holder.
PAGE 4
CIRCULAR FRAME ALIGNMENT 1. Use 120° PATTERN, fold edges of pattern. (See figure 5) 2. Place the tip of the PATTERN on the center of FRAME A and FRAME B where it intersects. 3. Align two frames base on the shape of the PATTERN. 4. After aligning the FRAME A and FRAME B, tighten it with NUT and BARREL NUT. (See figure 3) 5. Repeat step 4 for FRAME B and FRAME C.
PAGE 5
bolt nut barrel nut PATTERN CIRCULAR FRAME B 120° CIRCULAR FRAME A CIRCULAR FRAME C FIGURE-4 Page 5 of 6
PAGE 6
FO LD IN G LIN E FOLDING LINE FOLDING LINE 120° PATTERN 120° FO G IN LD E LIN FIGURE-5 FOLDING LINE Page 6 of 6 101616jbz