Manual

MODELS 12089, 12090, 12204 Parts List
REF PART
No. No. DESCRIPTION
TRANSMISSIONCOVER& SHIFTLEVER
BRACKETASSEMBLIES
1 1186299 Bolt-hex hd., #10-32 x 3/8",
self-locking flange ..................... 3
2 9463 Knob-tines/PTOclutch lever,
tapered, plastic .......................... 1
3 2263 Detent Plate-tines/PTOclutch lever
(incLRef. No. 4) ......................... 1
4 1900758 Decal-operating instructions,
detent plate................................ 1
5 1186347 Bolt-flanged hex hd.,
3/8-16 x 1-1/2". ......................... 4
7 1186329 Bolt-flanged hex hd.,
5/16-18 x 3/4", Grade5 ............ 1
9 1107382 Washer-fiat, 5/16", S.A.E.............. 1
10 1900870001 Bracket-shift levers(incl. Ref.
No. 86) ...................................... 1
11 9362 Pin-spring, 1/8". ........................... 1
12 9838 Nut-castle (slotted), 1/2"-20, call
Tech Servicefor tightening
instructions ............................. 1
13 9934 Washer-shoulder, 1/2". ................ 1
14 9932 Washer-disc spring ...................... 2
15 .... Lever-wheel speed shift (see page
51, Ref. No.5 for part number). 1
16 1900869001 Cover-power unit transmission .... 1
16A 2566 Cover-power unit transmission
(incl. Ref. No.'s 18,19, 20, 21, 22,
23 and 24) ................................. 1
17 1123 Gasket-transmission cover........... 1
18 1100045 Bolt-hex hd., 5/16-18 x 1",Grade 5,
(remove with care) ................... 1
19 1186230 Nut-hex, 5/16"-18......................... 1
20 1901439 Spring-neutral plunger (remove
with care) .................................. 1
21 1035 Plunger-neutral (remove withcare)
(incl. Ref. No. 22) ...................... 1
22 1901440 Clip Ring-retains neutralplunger.. 1
23 1186393 Nut-hex, flangelocknut, 3/8"-16... 1
24 1902004 Bolt-hex hd., 3/8-16x1-1/2",
threaded full length.................... 1
TINES/PTOCLUTCHLEVERASSEMBLY
25 1900878001 Lever-eccentric, tines/PTOclutch.
(also see Ref. No.'s 1, 2,3 and
4 listed above)........................... 1
26 1100804 Bolt-hex hd., 1/4-20 x 1/2". .......... 1
27 2123 Bushing-tines/PTO clutch lever
eccentric shaft ........................... 1
REF
QTY. No.
28
29
3O
31
33
34
35
36
37
38
39
40
42
43
44
45
45
45
45
46
47
48
49
50
51
52
53
PART
No. DESCRIPTION QTY.
9516
2461
9911
9672
9500
1909139
9301
1100004
1186310
1900879001
1983632
1124-2
1224-1
Retaining Ring-(snap ring),
external...................................... 2
Eccentric-shaft, tineslPTO clutch
lever........................................... 1
Lockwasher-hi-collar, 1/4"............ 1
Screw-socket hd., 1/4-20 x 3/8" ... 1
DRIVESHAFTASSEMBLY
Retaining Ring-external ................ 1
Dog Clutch-power unit ................. 1
Key-3/16 sq. x 1".......................... 3
Bolt-hex hd., 5/16-24 x 3/4", self-
locking flange, Grade5 .............. 1
9944 Washer-disc spring (concave)...... 1
2107 Pulley-transmission drive, cast iron 1
50027 Washer-flat, hardenedshoulder
1-1/4"......................................... 1
Bolt-hex hd., 1/4-20 x 3/4", front
bearingcap ................................ 3
Cap-front bearing ......................... 1
Seal-oil, front bearing cap ............ 1
Gasket-front bearing cap .............. 1
Shim-front bearing cap,.
010" thick ..............................As Req'd
1224-2 Shim-as above, .030"...............As Req'd
1224-3 Shim-as above, .005"...............As Req'd
1224-4 Shim-as above, .062"...............As Req'd
1714 Bearing& Cup-tapered cone roller
bearingwith cup (race). Coneand
cup sold as set only ................... 2
11601 Shaft-main drive, power unit. Incl.
integral worm, plus two pressed-
on cone roller bearings,two
bearingcups and two shoulder
washers ..................................... 1
9617 Seal-oil, drive shaft, rear .............. 1
9517 RetainingRing-(snapring), intemal........1
9309
1060A
9604
1132-1
PINIONSHAFTASSEMBLY
Pin-roll (spirol), 114x 2"............... 2
Plug-retaining, pinion bearing (incl.
Ref. No. 62) ............................... 2
O-Ring-retaining plug................... 2
Shim-retaining plug, I-I164" inner
dia., .033"thick (on right side
only one #1132-I shim is also
used betweenbearing and washer,
Ref. No.'s 54 & 55).................... As
Req'd
(continued onpage 55)
53