O ® / m / Operator's Manual i.
THANK YOU Rules for Safe Operation Thank you for buying this quality product. This modern outdoor power tool will provide many hours of useful service. You will find it to be a great labor-saving device. This operator's manual provides you with easy-tounderstand operating instructions. Read the whole manual and follow all the instructions to keep your new outdoor power tool in top operating condition.
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and their explanations, deserve your careful attention and understanding. The safety warnings do not, by themselves, eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures. SYMBOL MEANING SAFETY ALERT SYMBOL: Indicates danger, warning, or caution. Attention is required in order to avoid serious personal injury.
• CORDSETS:Makesureyourcordsetis ingood condition.Whenusinga cordset,besureto usea cordthatis heavyenoughto carrythecurrentthatyour unitwilldraw.An undersized cordsetwillcausea drop in linevoltageresultingin lossof powerand overheating. Seetheoperator'smanualfortheunitthat willpowerthisadd-onfortherecommended cordsize. • Inspect all extension cords and the unit power connection periodically. Look closely for deterioration, cuts or cracks in the insulation. Also inspect the connections for damage.
SAFETY AND INTERNATIONAL SYMBOLS This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety, assembly, operating and maintenance and repair information. SYMBOL A © @ MEANING • SAFETY ALERT SYMBOL Indicates danger, warning, or caution. May be used in conjunction • WARNING - READ OPERATOR'S with other symbols or pictographs.
APPLICATIONS With Trimmer Add-On: • Cutting grass and light weeds. • Decorative trimming around trees, fences, etc. _ Line Cutting \ \ \ Blade \ \ \ \ \ \ \ Cutting Gear Housing \ \ Cutting Attachment 6 Hanger Attachment Shield
ASSEMBLINGTHE COUPLER Coupler The following Troy-Bilt Add-Ons are also available for your unit: Blower/Vacuum ........................... TBBV Cultivator ................................ Hedge Trimmer TBGC ........................... TBHS Edger ................................... Snow Thrower Turbo Blower Tree Pruner Removing L TBLE ............................ TBST ............................. TBTB .............................. L Fig. 2 the Add-Ons 3.
HOLDING THE TRIMMER NOTE: DO not rest the Bump Head TM on the ground while the unit is running. and body protection to reduce the risk Of injury when operating this unit. Some line breakage will occur from: _ J Before operating the unit, stand in the operating position (Figs. 4 & 5). Check for the following: • The operator is wearing eye protection and proper clothing. • The right arm is slightly bent, and the hand is holding the shaft grip.
LINE INSTALLATION FOR THE SPEEDSPOOL ® Always use Genuine Factory Parts TM 0.080 inch (2.03 mm) replacement line. Line other than specified may make the engine overheat or fail. Trimming Line Eyelet WARNING: Never use metal-reinforced Pine, wire, or rope, etc. These Can break off and become a dangerous project e. There are two methods to replace the SpeedSpool® trimming line.
7. Repeat procedures 4-6 with the second piece of line. 2. 8. Hold the outer spool. Wind the inner reel counterclockwise until approximately four (4) inches (102 mm) of line remain (Fig. 12). Pull the old inner reel with existing line from the outer spool. 3. Insert the ends of the prewound inner reel line into the outer spool eyelets (Fig. 15). Push the new inner reel, arrow side up, into the outer spool. NOTE: Do not wind the inner reel before installing the second piece of line. .2 Fig. 15 4.
2. Pull out the bump knob, spring, and foam seal (Fig. 14). 3. Pull the inner reel with existing line from the outer spool (Fig. 14). 4. Remove any existing line from the inner reel before cleaning. Remove any debris or grass from the knob, spring, inner reel, and foam seal. Wash the inner reel with warm soapy water (Fig. 17). CLEANING Use a small brush to clean offthe outside of the unit. Do not use strong detergents.
CAUSE ACTION Cutting head bound with grass Stop the unit and clean cutting attachment Cutting head out of line Refill with new line Inner reel bound up Replace the inner reel Cutting head dirty Clean inner reel and outer spool Line welded Disassemble, remove the welded section and rewind the line Line twisted when refilled Disassemble and rewind the line Not enough line is exposed Push the bump knob and pull out line until 4 inches (102 mm) of line is outside of the Cutting attachment CAUSE
Unit Weight ..................................................................... Cutting Mechanism ............................................. Line Spool ................................................................... Line Spool Diameter ........................................................... Trimming Line Diameter ..................................................... Cutting Path Diameter ......................................................... SpeedSpooP 3 Ibs. (1.36 kg.
BOOM Item 1 2 Part NO.
MANUFACTURER'S O I m LIMITED WARRANTY FOR: I_m The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise purchased and used in the United States, its possessions and territories. Troy-Bilt LLC warrants this product against defects in material and workmanship for a period of two (2) years commencing on the date of original purchase and will, at its option, repair or replace, free of charge, any part found to be defective in material or workmanship.