08172016-v4 Page 1
Index INSTALLATION INSTRUCTIONS Package Contents / Tools Required......................................................... Page 1 Prepare Door and Jamb..............................................................................Page 2 Adjusting Deadbolt Latch Set.....................................................................Page 3 Installing Deadbolt Latch Set.....................................................................Page 4 Preparing Interior Assembly......................................
INSTALLATION INSTRUCTIONS Package Contents Entry keys (2 ea.) Deadbolt Latch Set (Adjustable) 2-3/8” (60mm) to 2-3/4” (70mm) Interior Assembly Mounting Plate Exterior Assembly 5/16” (8mm) Screws - 2 ea. 7/8” (22mm) Screws - 2 ea. 3/4” (19mm) Screws - 5 ea. 1” (25mm) Screw - 1 ea. Deadbolt Strike Plate Tools Required Tools Required for Installation on Pre-drilled Doors: • Phillips Head Screwdriver Batteries (not included) Electronic lock requires (4) High Quality AA Alkaline batteries.
PREPARE DOOR AND JAMB NOTE: For installation on doors with pre-drilled holes skip to page 4. 1. TEMPLATE a. Cut out template printed on page 15 & 16 of this Manual (Figure 1a). b. Fold template and place on door 36” (915mm) from the ground as marked (Figure 1b). 2. MARK THE DOOR FOR DRILLING b. Mark center hole on door edge through guide on template for 1” (25mm) latch bolt (Figure 2a). a.
ADJUSTING DEADBOLT LATCH SET NOTE: Deadbolt Latch Set is shipped with the backset set at 2-3/8” (60mm) Measure the backset (backset is distance between edge of the door and the center of Lock). 1. TO CONVERT FROM 2-3/8” (60mm) BACKSET TO 2-3/4” (70mm) BACKSET a. Hold latch with numbers facing forward and thumb pressing on the bolt (Figure 1a). b. Rotate the cylinder cover clockwise (Figure 1b). c. Pull and twist the extension plate all the way out (Figure 1c). d.
INSTALLING DEADBOLT LATCH SET 3. INSTALLING THE DEADBOLT LATCH SET (need phillips head screwdriver) a. Insert Deadbolt Latch Set into door edge hole with the word “UP” and the arrow on the extension plate facing UP. Cross shaped spindle connector will be at the bottom of the Deadbolt Latch Set (Figure 3a). b. Make sure the face plate sits flush with the door. Do not force the latch into the mortise flush. Chisel out excess material if Figure 3a necessary for a flush fit. c. Using two 3/4” (19mm).
PREPARING THE INTERIOR ASSEMBLY 5. UNPACK THE INTERIOR ASSEMBLY a. Remove the battery cover by sliding the cover upward. b. Locate the screws holding the Mounting Plate to the Interior Assembly. Remove the screws to release the Mounting Plate from the Interior Assembly. 6. SET THE ENTRY SWITCH FOR LEFT OR RIGHT HANDED DOOR a. Gently move the switch to “L” for Left Handed Door (Figure 6a). b. Gently move the Switch to “R” for Right Handed Door (Figure 6b). Entry Switch (Left or Right) Figure 6a-b 7.
INSTALLING EXTERIOR ASSEMBLY 8. INSTALLING THE EXTERIOR ASSEMBLY Work with the Door Open for easy access. a. Unpack the Exterior Assembly. Use care to not scratch the green circuit board during handling and installation. b. Check that the Rubber Gasket is properly seated on the Exterior Assembly (Figure 8a-b). c. Insert the Exterior Assembly onto the door with the tailpiece going through the Deadbolt Latch Set cross shaped spindle connector in the VERTICAL POSITION.
INSTALLING INTERIOR ASSEMBLY 11. ATTACH THE CONTROL WIRE TO THE INTERIOR ASSEMBLY a. Use care to attach the Control Wire male plug to the Interior Assembly female socket connector (Figure 11a). b. Do not force the Control Wire male plug into the Interior Assembly female socket connector (Figure 11b). c. The Control Wire male plug has two alignment tabs on the smooth side of the plug which is the top of the plug (Figure 11c). d.
INSTALLING INTERIOR ASSEMBLY (CONT.) 13. Installing Batteries a. Insert 4 AA high quality Alkaline batteries into the Battery Compartment in the direction noted +/- on the Compartment. The Lock will beep 2 times, the keypad will illuminate blue, and the Light Indicator will flash green twice to signify that it has received power (Figure 13a). NOTE: Do not touch the Keypad until the blue light turns off. Do not use rechargeable batteries or non-alkaline batteries. b.
OPERATION INSTRUCTIONS Exterior Assembly Overview Light indicator Green • Indicates Successful Programming Step • Indicates Unlocking is Successful Red • Indicates Failed Programming Step • Indicates Locking is Successful Lock button Lock - Used to lock door Clear - Used to clear wrong keypad entries Unlock button Unlock - Used to unlock door Programming - Used in programming steps Batteries (not included) Electronic lock requires (4) High Quality AA Alkaline batteries.
Locking and Unlocking TO UNLOCK THE LOCK Using Keypad: Enter a valid User Code (default code is 1234) and press 1 beep and lights green. TO LOCK THE LOCK Using Keypad: Press and hear and then hear 2 beeps and lights red. Changing Programming Code CHANGE CURRENT OR PRESET PROGRAMING CODE PC Factory default Programming Code PC = 123456, this is the master password for your lock. All programming functions require this code.
Deleting User Codes DELETE ONE EXISTING OR PRESET USER CODE The unit comes with a factory User ID ID = 01 for User Code UC = 1234. IMPORTANT: To delete 1 User Code UC , the lock must have more than 1 User Code in its database. PC 2 Existing re-enter ID UC ID Hear 1 beep and Light Indicator illuminates green. DELETE ALL USER CODES IMPORTANT: this will delete the user codes but not the programming code, enter the following. PC 3 re-enter PC Hear 1 beep and Light Indicator illuminates green.
Vacation Mode With Vacation Mode enabled, the system enters into low-power comsumption mode. During this mode, all buttons and functions will be invalid until they are re-enabled (see steps below). ENABLE: PC 10 1 Hear 1 beep and Light Indicator illuminates green then lock door DISABLE: To disable the Vacation Mode, you must press and hold for more than 3 seconds, then input PC to unlock the door. Vacation Mode is now disabled.
Restore Factory Settings To reset the lock to the original factory settings including the Programming Code PC and all User Codes UC remove one battery for 10 seconds. Reinsert the battery and wait for a long and short beep. Press 3 times within 3 seconds. The lock will beep and the light indicator will turn green. Low Battery Warning Beeps and LED flashes red for 5 seconds. Replace with good quality alkaline batteries. Note: Removing batteries does not erase active Programming or User Codes.
INSTALLATION TROUBLE SHOOTING Issue Solution Latch Working BackwardsLock unlocks when lock button is pushed or locks when unlock button or code is pushed. Direction switch is set to incorrect setting. Remove the Interior Assembly and move the switch to the opposite direction. • Check that your switch is set in the correct position Left or Right Handed door. If Correct • Rotate Interior Knob and reinstall Interior Assembly. Retest again while holding Interior Assembly in place.
Page 15 MARK FOR 1 83 "(35mm) DOOR THEN DRILL 1"(25mm) HOLE IN CENTER OF DOOR EDGE (2" IN DEPTH) MARK FOR 1 34 "(45mm) DOOR FOLD HERE ON DOOR EDGE IMPORTANT! PLACE TEMPLATE ON HIGH EDGE OF DOOR BEVEL 23/4"BACKSET 23/8"BACKSET FOR INSTALLING ENTRY LOCK AND DEADBOLTS TEMPLATE DRILL 2-1/8"(54mm) HOLE MARK CENTER OF HOLE ON DOOR FACE
Back of Template Page 16
CONSUMER ASSISTANCE EMAIL: LHICustomerService@lewishymaninc.com WEBSITE: www.truboltlocks.info ADDRESS: Consumer Assistance Dept. Lewis Hyman, Inc.
Programming Record My Codes: Programming Code Date Created (6 digits) / / User Code 01 (4-8 digits) / / User Code 02 (4-8 digits) / / User Code 03 (4-8 digits) / / User Code 04 (4-8 digits) / / User Code 05 (4-8 digits) / / User Code 06 (4-8 digits) / / User Code 07 (4-8 digits) / / User Code 08 (4-8 digits) / / User Code 09 (4-8 digits) / / User Code 10 (4-8 digits) / / User Code 11 (4-8 digits) / / User Code 12 (4-8 digits) / / User Cod
Programming Record (Cont.
Limited 1-Year Electronic Warranty Limited Lifetime Mechanical and Finish Warranty This Tru-Bolt® product comes with a 1-Year Limited Warranty on Electronic Parts and a Limited Lifetime Mechanical and Finish Warranty against defects in materials and workmanship under normal use to the original residential user. Simply bring this product with the original sales receipt back to your nearest Menards® retail store.
Manufactured by: Lewis Hyman Inc.
