User manual

Operating instructions
230 V/AC LED Control Printed Circuit
Board for standard LEDs 20 mA
Item no. 1570586
Intended use
The control printed circuit board serves for direct and icker-free connection of an
LED to common household voltage (230V AC/50Hz). The necessary LED is not con-
tained in the delivery and must be connected separately by the user.
The assembly group must be installed completely (incl. LED) in a casing where it is
protected from accidental touching.
For safety and approval purposes, you must not rebuild and/or modify this product.
If you use the product for purposes other than those described above, the product
may be damaged. In addition, improper use can cause hazards such as short circuit-
ing, re, electric shock etc. Read the instructions carefully and keep them. Make this
product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All
company names and product names are trademarks of their respective owners. All
rights reserved.
Delivery content
• LED control printed circuit board
• Operating instructions
Latest operating instructions
Download the latest operating instructions via the link www.conrad.com/downloads
or scan the QR code shown. Follow the instructions on the website.
Explanation of symbols
The lightning symbol inside a triangle is used when there is a potential risk
of personal injury, such as electric shock.
An exclamation mark in a triangle indicates important instructions in this
operating manual that absolutely have to be observed.
The arrow symbol indicates specic tips and advice on operation.
Safety instructions
Read the operating instructions carefully and especially observe the
safety information. If you do not follow the safety instructions and
information on proper handling in this manual, we assume no liability
for any resulting personal injury or damage to property. Such cases
will invalidate the warranty/guarantee.
Attention, important note!
Only persons with relevant electro-technical knowledge and experi-
ence should carry out the installation! *)
If it is not installed properly, you risk:
• your own life
• the life of the person using the electrical system.
If it is not installed properly, you risk severe damage to property, e.g., by
re.
You face the risk of being held liable for personal injury and material dam-
age.
Contact an Electrician!
*) Specialist knowledge required for the installation:
In particular the following expertise is required in regards to the installation:
• the applicable „5 safety rules“: Switch off power; secure against switch-
ing back on; determine voltage-free status; earthing and short-circuiting;
cover or fence off nearby live parts
• Choose appropriate tools, meters and, if necessary, personal protective
equipment
• Evaluation of the measurement results
• Select the electrical installation material to ensure the shutdown condi-
tions
• IP protection types
• Installation of the electrical installation material
• Type of mains supply network (TN system, IT system, TT system) and
the connection conditions that follow from them (classical earthing, pro-
tective earthing, required additional measures, etc.)
If you do not have the expertise required for the installation, do not
connect and install it yourself, but ask a qualied technician.
a) General
• The unauthorised conversion and/or modication of the product is not
allowed for safety and approval reasons.
• Maintenance, adjustment or repair work may only be carried out by an
expert/authorised service centre familiar with the hazards involved and
the relevant regulations.
• The product is not a toy and should be kept out of the reach of children!
There is danger of a life-threatening electric shock! Install the product out
of the reach of children.
• Protect the product from extreme temperatures, direct sunlight, strong
vibrations, high humidity, moisture, combustible gases, vapours and sol-
vents.
• On industrial sites, the accident prevention regulations of the associa-
tion of the industrial workers‘ society for electrical equipment and utilities
must be followed!
• Do not leave the packaging material lying around carelessly as it may be
a danger to children.
• Handle the product with care; it can be damaged by impacts, blows or
falls even from a low height.
• If you have doubts about how the product should be operated or how to
safely connect it, consult a qualied technician.
• Maintenance, adjustment and repair work should only be carried out by
an expert or a specialised workshop.
• If you have any questions that are not answered in these operating in-
structions, please contact our technical customer service or other profes-
sionals.
b) Installation/connection
• During installation, all poles must be disconnected from the mains volt-
age, e.g., via RCD. There must be an appropriately dimensioned fuse or
circuit breaker between the RCD and the product.
• The device must be voltage-free during installation and connection. Fur-