Datasheet

ManualsBrandsTRU COMPONENTS ManualsSwitches & ButtonsJoystick 12 Vdc Steel lever (straight) Solder pins 98002C2 1 pc(s)

Page 1 of 7 QR-QE-20/2003.08.01

SPECIFICATIONS (

規格書

)

編號 NO. ：

F-JN10K-01-030

公司名稱 CO. Name ：

型號名稱 Model Name ：

FJN10K-N1B10K01

一、ELECTRICAL CHARACTERISTICS 電氣特性

日期:2015 年 11 月 02 日

序號

NO.

項目

ITEM

性能

PERFORMANCE

測試條件

PTEST CONDITIONS

Total

resistance

全阻值

▓10K±20% □50K±20%

□100K±20% □120K±20%

Between terminal 1 and terminal 3.

1-3 端子間.

Resistance

taper

阻抗特性型式

Type B; Refer to attached drawing

“Resistance taper characteristics”

B 型；見附頁“阻型特性圖＂

Percentage of the voltage of terminal 1-2 to

the voltage of terminal 1-3.

端子

1-2

電壓對端子

1-3

電壓的百分比。

Rated voltage

額定電壓

Linear Taper B：AC 50V

DC 5V

B 型: AC 50V

DC 5V

E=√PR

E:額定電壓 Rated voltage(V)

P:額定功率 Rated power(W)

R:公稱全阻值 Nominal total resistance(Ω)

The rated voltage is calculated by above

formula. When the rated voltage exceeds the

maximum operating voltage, the maximum

operating voltage should be the rated voltage.

額定電壓按以上公式計算，當額定電壓超

過最大工作電壓時，最大工作電壓即為額

定電壓.

Rated power

額定功率

Linear Taper B: 0.0125W

B 型: 0.0125W

The rated power should be changed

according to the following chart when the

ambient temperature changed.

它與環境溫度按以下曲線變化。

Derating curve of rated dissipation

Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau

Datasheet

Item no. 1566390 V1_0118_01_en

Summary of content (10 pages)

PAGE 1
Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau Datasheet Item no. 1566390 V1_0118_01_en SPECIFICATIONS (規格書) 編號 NO. 公司名稱 CO. Name ： F-JN10K-01-030 ：型號名稱 Model Name ： F J N 1 0 K - N 1 B 1 0 K 0 1 一、 ELECTRICAL CHARACTERISTICS 電氣特性序號 NO.
PAGE 2
10% or less of the total resistance for over 60°(60°included) carbon film angle (Before the life test) ; 15% or less of the total resistance for 40 ° thru 60 ° carbon film angle (Before the life test) ; 20% or less of the total resistance for 30° thru 40°(40°included) carbon film angle (Before the life test) ; 25% or less of the total resistance for 25° thru 30°(30°included) carbon film angle (Before the life test) ; 30% or less of the total resistance for 20° thru 25°(25°included) carbon film angle (Before
PAGE 3
碳膜角度為 60°(含)以上時,全阻值的 15%以下(壽命測試後); 碳膜角度為 40 °~60°時,全阻值的 20%以下(壽命測試後); 碳膜角度為 30°~40°(含)時,全阻值的 25%以下(壽命測試後); 碳膜角度為 25°~30°時(含),全阻值的 30%以下(壽命測試後); 碳膜角度為 20°~25°時(含),全阻值的 35%以下(壽命測試後); 碳膜角度為 20°(含)以下時,全阻值的 40%以下(壽命測試後). 6 Voltage Divider Error 分壓誤差值 43.5%~56.5% Voltage divider error is defined the ratio of the voltage terminals 1-2 to terminals 1-3 after the drive arm rested. 5V D.C.
PAGE 4
3 Pull strength of lever 搖杆拉拔強度 More than 5.0 Kgf 3 seconds min 大於 5.0Kgf，至少 3 秒鐘 Apply specified pull force on the lever upward. 作用於搖杆上，沿搖杆方向向上. 4 Push Strength of lever 搖杆推強度 More than 3.0 Kgf 3 seconds min 大於 3.0Kgf，至少 3 秒鐘 Apply specified push force on the lever downward. 作用於搖杆上，沿搖杆方向向下. 5 Operating force of lever 搖杆作用力 6 Accuracy of reset position of lever 搖杆復歸精度 7 Operation angle of lever 搖杆使用有效角度 Test position： More than 10 degrees deflection of lever. 搖杆偏斜 10 度以上之位置測定.
PAGE 5
3 4 Cold 耐寒性 Damp heat 耐濕性 The total resistance change should be within ±20%. To be operated mechanically. 全阻值變化要在±20%以內，機械方面能動作。 Insulation resistance: more than 10M Ω with 250V insulation resistance tester. The total resistance change should be within ±20%. To be operated mechanically. 用 250V 絕緣測試機測試，絕緣阻抗 10MΩ以上, 全阻值變化要在±20%以內, 機械方面能動作.
PAGE 6
Manual Soldering: Less than 350℃ and quicker than 3 seconds. 手銲: 350℃以下，3 秒以內 Number of cycles 耐久次數值 8 Total resistance≦Initial value±20%. No mechanical malfunction. 全阻值變化≦初始值±20% . 機械方面能動作. ■Standard life 標準壽命： 1,000,000 cycles Min 1,000,000 次以上。 □Long life 長壽命： 2,000,000 cycles Min 2,000,000 次以上。四、 SWITCH CHARACTERISTICS (FOR WITH-SWITCH TYPE) 開關規格 (適用於帶開關機種 ) 序號項 NO.
PAGE 7
Less than 100 mΩ 低於 100 mΩ Apply 2 times of the operating force of the static load on the vertical direction of the lever, measure the resistance by using the Contact Resistance Tester with 1KHZ, 20mV, 5~50mA of current. 將兩倍於作動力之靜負荷加於操作柄之中央以(1KHZ,20mV, 5~50mA)微電流接觸阻抗計測定. More than 100 MΩ 100 MΩ以上 A voltage of DC100V is applied between terminals. 以 DC100V 之電壓加於端子間測定. 8 Withstand voltage 耐電壓 There shall be no damage, arc or dielectric breakdown.
PAGE 8
Y Y REST POSITION 66°±6° X DIRECTION 未指定容許±尺寸之公差 10以下 ±0.3 01 03 04 05 06 07 08 09 10 Code 碳膜層 (Carbon) SPEC Code 11 12 13 14 15 16 17 18 19 Code 38 42 43 47 53 硫化層 (Anti-Sulfurated) Code A(Carbon) C0 C3 C5 D0 D5 ANGLE A B 45° 8° 32° 8° 20° 6° 45° 10° 6° 45° 6° 46° 8° Code 20 22 26 30 32 33 34 35 44 ANGLE A C 53° 12° Code 54 60 59 66 71 Code 48 51 52 55 56 73 74 A(Carbon) Code A(Carbon) B(Silver) 64 銀層 (Silver) 低碳層 (Low Resistance) DISPOSAL UNIT 5 MM 2.
PAGE 9
成品包裝規格書 PRODUCT PACKING STANDARD 編號 NO. 公司名稱 CO. Name 型號名稱 Model Name : F-JN10K-01-030 : : FJN10K-N1B10K01 日期 (DATE): 2015/11/02 1. 成品包裝方式 PACKING METHOD: 1.1. 將 V.R 成品置放於單個膠盒內蓋上膠蓋，並將膠盒疊放在一起再用膠紙將其扎好。 Let the V.R be placed into plastic box and cover the case, and the plastic boxes be superposed one by one and use adhesive tape them together. 1.2.
PAGE 10
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represents the technical status at the time of printing. © Copyright 2018 by Conrad Electronic SE.