Product Manual

ManualsBrandsTruckStar ManualsCanopies + SheltersBuyers Products Dump Tarp Roller Kit — 7ft. x 12ft. Mesh Tarp

9049 Tyler Blvd. • Mentor, Ohio 44060

Phone (440) 974-8888 • Fax (440) 974-0165

Toll-Free Fax 800-841-8003 • buyersproducts.com

Installation Instructions

—continued inside

1. Determine the location of the tarp roller. The

tarp roller should be mounted above the cab on the

dump body’s cab guard. To prevent damage from

loads being dumped into the body, the tarp roller

should be mounted outside of the dump body’s

load area. Also, verify the location is accessible for

winding the tarp up.

2. Clamp the bearing bracket assemblies (item

4&5) to the dump body in the locations determined

in step 1. The bearing bracket assembly with the

detent lever (item 5) is to be mounted on the

driver’s side of the dump body. Make sure the

brackets are aligned vertically as well as from front

to back by measuring from a common point on

each side of the body. Verify the bearing bracket

assemblies are mounted high enough to

accommodate the tarp when rolled onto the roll bar

assembly.

3. Mark the bearing bracket mounting hole’s

locations onto each side of the dump body. Remove

the brackets and drill 13/32" holes in the four

marked locations.

4. Assemble the bearing brackets to the dump

body using the four 3/8-16 x 1 cap screws, lock

washers and nuts supplied. Do not tighten fasten-

ers at this time, just hand tighten to hold brackets

in position.

5. Locate the inner hex tube (item 1) and make

a pencil mark in the center of the tube’s length.

Insert the inner hex tube half way into the driver’s

side roll tube assembly (item 2). Insert the

passenger’s side roll tube assembly (item 3) onto

the opposite end of the inner hex tube. Measure

the distance between the inside of the mounted

bearing brackets (for measurements less than

81.75”: The driver’s and passenger’s side roll tube

assemblies (items 2 & 3) will need to be shortened

by an equal amount to obtain the proper width).

Separate the roll tubes, so the length of the

complete roll tube assembly from adaptor to

adaptor is ¼" less than the distance between

mount brackets. Locate the pencil mark, and verify

For DTR Series Dump Tarp Kits

Summary of content (4 pages)

PAGE 1
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • buyersproducts.com Installation Instructions For DTR Series Dump Tarp Kits 1. Determine the location of the tarp roller. The tarp roller should be mounted above the cab on the dump body’s cab guard. To prevent damage from loads being dumped into the body, the tarp roller should be mounted outside of the dump body’s load area. Also, verify the location is accessible for winding the tarp up. 2.
PAGE 2
that the inner hex tube is centered inside the outer roll tube assemblies. Screw each roll tube assembly to the inner hex tube using one ¼" x 1" self drilling and taping screw (item 9A) 2" from the end of the outer tube. 6. Slide the complete roll tube assembly into the 5" loop in the end of the tarp. Verify that the webbing in the seams of the tarp will be on the bottom when installed. Note: The roll tube end of the tarp only has one row of webbing reinforcement. 7.
PAGE 3
SEE DETAIL A SPROCKET SEE DETAIL DETENT LEVER SEE DETAIL B TARP PULL ROPE ATTACH HOOK TO CENTER GROMMET PULL ROPE STORAGE HOOKS MOUNT 15-17" APART DETAIL A Fig. 1 C REAR BAR KIT (OPTOINAL) DETAIL REAR TARP STRAPS AND HOOKS CRIMP HOOKS TO SECURELY ATTACH C PULL ROPE STORAGE HOOKS MOUNT 15-17" APART Fig. 3 DETAIL B Fig. 2 WARRANTY Buyers Products Co.
PAGE 4
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • buyersproducts.com Dump Body Tarp Roller Parts List ITEM PART NO. QTY.