Model: MD-2B Mini Duo Burner User Guide
Table of Contents I. Important Safety Information 1-3 II. Control Panel Overview 4 III. Specifications & How to Use 5 • Operating the Keys 5 • Stand by Mode 5 • Lock 5 • Switch off the Lock 5 • Readiness Mode 6 • Menu On 6 • Power Sharing 7 • Set Timer Mode • Hot Surface Indicator 7 7 IV. Notes on using your Cooktop V. Compatible Cookware 7 8 VI. Cleaning and Maintenance VII. Counter Installation Instruction 8-9 10-11 VIII.
: • even with the built• only be performed by a qualified person. • While cooking fat or oil on the cooktop may ignite. There is a risk of burning and fire; therefore, never leave the cooktop unattended at anytime. • When the unit is on, do not touch outside the control panel as the surface may contain residual heat. • To protect against electric shock, do not immerse cord plugs or cooker in water (or other liquid substances). • When using any electric appliance around children, close supervision is required.
: • • It is important to be aware that the unit’ • When possible, Unplug the cooktop from the outlet when not in use and before cleaning. Allow to cool before performing any maintenance or repairs. • - heated surface. • Do not store items of interest to children in cabinets above the range or on the backguard of a range - children climbing on the range to reach items could get seriously injured. • • Do not repair or replace any part of the appliance unless specifically recommended in the manual.
II. Control Panel Overview: by 2 Surface remains hot after use. Do not touch! Attention: Le dessus reste chaud pres usage! 1 true INDUCTION 1. Left Cooking Zone 2. Right Cooking Zone 3 3. Ceramic - Glass 4. Left touch control panel 5. Right touch control panel U U Diagram make look different from actual product. 5 4 Power Temp Time Power -- + Temp Time -- POWER Menu-On Timer Lock + POWER Menu-On Timer Lock 12 6 Power Temp Time 7 8 -- + 9 10 11 POWER Menu-On Timer 6.
: Power 1800 Voltage 120V / 60Hz Power Range 100W - 18 10 Max Time 180 minutes Material Glass Ceramic Top / Metal Body Unit Measurements 20.
III. Specifications & How to Use: Readiness Mode While in the standby mode, press the “ON/OFF” key, it will make a “beep” sound once, indicating that the induction cooktop functions are ready to use. The unit will automatically return to standby mode if heating zone is not turned on within 30 seconds. Turning Off Unit: POWER When use of the cooktop is complete, press the “POWER” key. “POWER” light will turn off, indicating the unit is now on the standby mode.
III. Specifications & How to Use: Power Sharing When both burners are on, one of the two burners would not have a power level higher than level 7. Both of them together would not be more than level 10. If only one burner is on, the heating zone can maintain its full heat setting, but when operating both burners, their combined total is level 10, meaning that when operating the two burners at the same time, they will self adjust levels accordingly.
V. Compatible Cookware: by true INDUCTION Surface remains hot after use. Do not touch! Attention: Le dessus reste chaud pres usage! materials. Check your cookware’s retail box for the U U technology, grab a magnet and see if it your magnet stays on then your cookware cooktop! Power Temp Time Power -- + POWER Menu-On Timer Lock Temp Time -- + POWER Menu-On Timer Lock The following are not -resistant glass, ceramic, copper, aluminum pan/pots, roundbase less than 5 inches. VI.
VI. Cleaning and Maintenance: Cleaning Burned-on Residue: WARNING: Damage to the glass surface may occur if you use scrub pads or any other type of abrasive cleaning materials. 1. Allow the cooktop to cool. 2. Spread a few drops of the ceramic cooktop cleaner on the burned residue area. 3. Using the included ceramic cooktop cleaning pad, rub the residue area, applying pressure as needed. 4. If any residue remains, repeat the steps listed above. 5. cleaner and a paper towel.
Warning! For Your Safety: Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other be avoided. If cabinet space is available, the risk can be reduced by installing a range hood that protects horizontally IMPORTANT INSTALLATION INFORMATION All electric cooktops run off a single phase, three-wire cable, 240V/60Hz AC only electrical supply with ground. Minimum distance between cooktop and overhead cabinetry is 30”.
VI Allow a 2" space below the covered cable opening to clear the electric cable and allow space for installation of the junction box on the wall at the back of the cooktop. Before installing the cooktop: 1. Visually inspect the cooktop for damage. Also make sure all cooktop screws are on tight. Recheck all measurements to ensure they are correct. 2. Place the cooktop into the countertop cutout to ensure it fits properly Serial plate is located under the burner box of the cooktop.
Error Code Possible Cause • IGBT - Insulated Gate Bipolar Transistor • NTC - Negative Temperature Coefficient, to check the temperature of electronic elements • NTC1 - To check the temperature of IGBT • NTC2 - To check the temperature of heating center • Cooktop controls are locked. Cooktop does not work • Make sure Lock mode is turned off. • Check house lights to confirm power outage. • Power outage. • Contact manufacturer. • No cookware or improper cookware placement on the cooking zone.
Error Code Power sharing Possible Cause When two heating zones are turned on, will create a totla max 10 setting • • (Insulated Gate Bipolar “E0” appears in the • Transistor) overheating. Timer display “E1” appears in the Timer display • See POWER SHARING unit. • No cookware found or improper placement of cookware on the cooking zone. • Make sure the cookware is centered on the cooking zone, and that it’ • Supplied voltage to cooktop is too low.