DOUBLE BURNER COUNTER INSET User Guide
Table of Contents I. Cooktop Installation 1-3 II. Important Safety Information 4 III. Product Specifications 5 IV. How to Use 5 • Power Invariance Technology 5 • Using the Temperature Setting 6 • Using the Timer Function 6 • Built-in Safety Shut Off 6 • Turning Off Unit 6 V. Compatible Cookware 7 VI. Cleaning and Maintenance 7 VII. Troubleshooting Error Codes 8 Thank you for purchasing the True Induction double burner counter inset unit.
I. Dimensions and Placement for Cut-Out in Countertop -Cut a rectangle hole in the countertop where the cooktop is to be placed. The dimensions for the cut-out are 14 1/4” x 23 11/16” -The cut-out must be placed at least 2 1/2” from any side of the countertop.
Building of Supports for Cooktop Below the Counter -Any thickness of the countertop can be utilized, however, the thickness will determine if the supports are built into the walls of the cut-out, placed below the cut-out, or be built out from the bottom of the cut-out. -Two support beams between ½” and 1” in width and 2” in depth should be placed lengthwise (spanning 23 11⁄16”) 2 ¼” below the surface of the cut-out.
Clearance Needed for Air Circulation: -Below you will see a diagram of the airflow. Be sure not to block either the intake or exhaust. - For proper air circulation, allow at least 3” of clearance from the bottom of the induction cooker, to any shelving or storage. The underside of the countertop should not be closed off from the cabinetry underneath for better airflow.
II. Important Safety Information When using electrical appliances, basic safety precautions should always be followed. For the True Induction cooker, even with the built-in safety features, it is essential to heed all precautions. -When the unit is on, do not touch outside the control panel as the surface may contain residual heat. -To protect against electric shock, do not immerse cord plugs or cooker in water (or other liquid substances).
III. Specifications Power: ETL rated for 15 amp circuit Voltage: 120v / 60Hz Temperature Range: 150°F - 450°F (exact temperature settings) Level Selection: Select settings 1 through 10 Max Time: Set timer up to 150 minutes Material: Glass Ceramic Top Single Burner Unit Measurements: 23.5” width x 15” length x 3” height IV. How To Use -Plug the power plug into a standard outlet. -The ON/OFF switch will light up and the unit will sound to indicate on.
Using the Temperature Setting: -After the unit is turned on, you can opt to use the TEMP setting. To do this, press the function key labeled TEMP one time. The pre-set temperature is 270 degrees Fahrenheit. -Using the +/- keys, you can change the temperature setting at any time. Settings range from 150-450 degrees Fahrenheit. (Exact temperatures: 150, 180, 210, 240, 270, 300, 330, 360, 390, 420. and 450°F) Using the Timer Function: -After selecting the HEAT or TEMP mode, press the TIMER button once.
V. Compatible Cookware Induction requires pots and pans that are made of ferrous (meaning magnetic) materials. Check your cookware’s retail box for the induction symbol. To tell if your current cookware is compatible with the induction technology, grab a magnet and see if it holds to the bottom of the cookware. If your magnet stays on then your cookware is ready to be used on the True Induction single burner induction portable cooktop! Optimal cookware has a flat bottom and a diameter of 4.5” to 10”.
Troubleshooting Error Codes If the display shows an error code, please refer to this sheet for a potential solution. Error Code “_ _ _” on display and beep sounds Cause and Potential Solution Cookware is not compatible with the induction cooktop. There is no cookware on the induction cooktop. Make sure the cookware is induction compatible as explained on the previous page. E1 Voltage is under 75V E2 Voltage is over 145V E3/E4 The unit may be damaged, contact seller for support.
