User Manual

ManualsBrandsTruxedo ManualsAutomotiveTruXedo TruXport Soft Roll-up Truck Bed Tonneau Cover | 247101 | fits 93-08 Ford Ranger Flareside/Splash 6' Bed

P/N 1116032 Rev R

___

Owners & Installation Manual

READ INSTRUCTIONS - Failure to assemble cover properly will void warranty.

Damaged or missing parts?

Call

1-877-878-9336

Mon - Fri 8 am - 5 pm CT

Parts will be shipped to you factory direct.

Do not return kit to place of purchase.

Tools Required:

1/2” Socket

Specify length or make and

model of vehicle to inquire

about headers, cover, side

rails, or bows.

TruXedo, Inc.

P.O. Box 1078, 2209 Kellen Gross Dr., Yankton, South Dakota 57078

Call Toll Free: 1-877-TRUXEDO (1-877-878-9336) Fa x : (605) 664-9304

Visit Us Online: http://www.truxedo.com

Summary of content (6 pages)

PAGE 1
Owners & Installation Manual Read Instructions - Failure to assemble cover properly will void warranty. Damaged or missing parts? Call 1-877-878-9336 Mon - Fri 8 am - 5 pm CT Parts will be shipped to you factory direct. Do not return kit to place of purchase. Specify length or make and model of vehicle to inquire about headers, cover, side rails, or bows. Tools Required: 1/2” Socket TruXedo, Inc. P.O. Box 1078, 2209 Kellen Gross Dr.
PAGE 2
1 2 Install weather seal on cab end corner plugs: Set cover assembly on front bulkhead: weather seal corner plug pa ra ll el to bu lk he a d 3 Place side rails on pickup bed rails. Assemble clamps. Place rear clamps loosely over side rails & pickup bed rails. Insert side rail corner plugs into header: in 4 NOTE: Additional weather seal may be required for pickups with bed caps, tailgate protectors, or liners. Add weather seal if needed to seal appropriately.
PAGE 3
7 8 Tighten front clamps: Center side rails on pickup bed: 1/8” side rail ce nt align grooves in clamp with grooves in side rail clamp install front clamps as close to bulkhead as possible. tighten. er he sid ad e r er a on ils pic and ku ta i p be lga te d 1/8” 9 leave 1/8” clearance between tailgate header and side rails. Tighten clamps at tailgate: fold back header and cover, while holding side rail in place (see step 8). tighten clamp. repeat on opposite side rail.
PAGE 4
12 A Close cover: Release safety straps, and unroll cover over pickup bed. Open tailgate. ! 9 13 B C D E With tailgate open, hook tailgate header into header stops on both sides of vehicle. Press center of tailgate header down until both latches engage. Listen for double click. Secure loop to hook fasteners on one side rail by pressing edge of cover along full length of rail. Pull cover tight across width of pickup bed. Secure loop and hook fasteners on opposite side rail.
PAGE 5
Replacement Parts 1 2 6 3 7 5 8 4 31 11 9 27 15 12 10 18 31 33 16 32 13 29 19 17 14 20 19 21 21 25 26 22 25 26 28 22 24 23 30 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 _______ Truxport Cover * _______ Bow * 1703558 Corner Plug _______ Cab End Header * 1703557 Corner Plug 1703548 Cap Screw, 5/16” x 1 3/4” 1703530 Male Clamp 1703531 Female Clamp _______ Passenger’s Side Rail * 1116028 Safety Clips 1703561 Clamp Assembly _______ Driver’s Side Rail * 1703569 End Pl
PAGE 6
five year WARRANTY TruXedo, Inc. warrants that all new, unused products are free from defects in material and workmanship. This Five Year Limited Warranty is effective if the product is properly installed and used for the purpose intended. It applies to the original buyer only. TruXedo’s obligation under this Warranty is limited to repairing, or at its option, replacing any part that is returned, transportation prepaid, to TruXedo, Inc., Yankton, South Dakota, if the product is, in our judgment, defective.