C O N T R A C T O R P U M P S & G E N E R A T O R S BUILT F O R W O R K Electric Submersible Pumps • Engine Driven Pumps • Genera tors • Accessories w w w . t s u r u m i p u m p .
Electric Submersible Pumps LB Series • HS Series Features Long-life by design 1 TOP DISCHARGE, FLOW THRU DESIGN 2 MULTI-DIRECTIONAL DISCHARGE CONNECTOR: Can be configured for horizontal or vertical discharge. Providing for a more stable installation. 3 4 5 6 7 4 2 RUBBER CASING WITH LARGE ROUNDED CUT-WATERS: Resists wear and degradation of performance due to abrasive particles. 5 CABLE BOOT: Prevents kinking at cable entrance by extending bending radius.
12 8 MINIATURE THERMAL MOTOR PROTECTOR: Protects against, overheating & run-dry. 9 V-RING SEAL PROTECTOR: Protects mechanical seal from abrasive particles. 10 URETHANE, SEMI-VORTEX IMPELLER & WEAR PLATES: Resists wear by abrasive particles and does not depend on close tolerances to maintain pump performance. 4 5 Tsurumi Impeller polished, not worn by abrasive material. 8 Competitor Impeller is effectively worn out.
Electric Submersible Pumps GROUP PERFORMANCE RANGE Reliable and cost-effective pumps enable Tsurumi to remain an industry leader in the rental and construction markets. Our customers know that while many pumps may look the same, only Tsurumi incorporates the most durable components into the final manufactured product.
Electric Submersible Pumps LB-480 • LB-480A DEWATERING PUMPS LB-480 Slimline design pump allows to fit into 8" pipes. Powerful pumps built with durable materials in an easy handling design. Top discharge provides maximum motor cooling efficiency allowing continuous duty operation at low water levels and extended dry-run capability. LB-480A Automatic Submersible Pump performs like the non-automatic version in every aspect of construction site usage requiring a tough and durable pump.
Electric Submersible Pumps LB(T)-800 • LB-800A DEWATERING PUMPS LB-800 • LBT-800 Slimline design pumps allow to fit into 8" pipes. Powerful pump built with durable materials in an easy handling design. Top discharge provides maximum motor cooling efficiency allowing continuous duty operation at low levels and extended dry-run capability. LB-800 (Single Phase) • LBT-800 (Three Phase) Features • Designed to fit an 8" pipe. • Up to 59’ shut off head.
Electric Submersible Pumps LB-1500 • LBT-1500 DEWATERING PUMP LB-1500 • LBT-1500 Slimline design pumps fit into 8" pipes. Powerful pump built with durable materials in an easy handling design. Top discharge provides maximum motor cooling efficiency allowing continuous duty operation at low levels and extended dry-run capability. LB-1500 (Single Phase) • LBT-1500 (Three Phase) Features • • • • • Fits into 8" pipes • • Circle Thermal Motor Protector: Protects against, overheating over amperage & run-dry.
Electric Submersible Pumps HS HSZ TRASH PUMP HS TRASH PUMP Durable trash pumps in two sizes—a 1HP 3-inch discharge and a 1/2HP 2-inch discharge. Both designed to pump sand, solids and debris with minimal wear and clogging. HSZ AUTOMATIC TRASH PUMP Automatic trash pumps in two sizes, designed to pump sand, solids and debris with minimal wear and clogging. HS2.4S 70 60Hz HSZ3.75S 60 HS HSZ TRASH PUMP Features Total Head (ft) • Built-in shaft mounted agitator suspends solids.
Electric Submersible Pumps HSD SERIES SAND PUMP EXTREME DURABLE TRASH PUMP: Pump sand, solids and debris with minimal wear and clogging. HSD Series Features • Anti-wicking block prevents water incursion. • Oil Lifter extends seal life by ten times. • Dual Inside Mechanical Seal with silicon carbide faces provides longer operational life of any seal available. • V-Ring Seal design protects mechanical seal from abrasive particles. • Built-in larger shaft mounted agitator suspends solids.
Electric Submersible Pumps LSR GROUND DRAINAGE PUMP Pump holds suction for drainage to 0.2 inch water level. LSR2.4S Features • Urethane, Semi Vortex Impeller and Wear Plates for maximum durability and maintaining pump performance. • Dual Inside Mechanical Seal With SiC faces provides longer operational life. • Oil Lifter provides lubrication of the seal faces. (Patented) • V-Ring Seal design protects mechanical seal from abrasive particles.
Electric Submersible Pumps F-13 UTILITY PUMP Oil free economical submersible pumps for clean surface water application. With built-in check-valve for houses, yards and gardens. Available ready to plug-in, with built-in level control, 1 1/4" or 3/4"NPT discharge. 30 F-13 Features • Completely oil free air filled motor protected by 3 oil seals. • Built-in thermal motor protector. • Incorporates a check valve built into the discharge. • Pump can be operated either manual or automatic.
Electric Submersible Pumps LH LHW THREE PHASE SLIMLINE PUMP Fits in an 8 inch pipe! Tsurumi introduces an ultra-slim pump with very high head that fits inside an 8 inch pipe. Ideal for deep-well pre-dewatering. LH LHW Slimline Features Circle Thermal Motor Protector: Protects against, overheating over amperage & run-dry. 1 Anti-Wicking Block: Prevents water incursion due to capillary wicking, should the power cable be damaged or the end submerged. 2 LH23.
Electric Submersible Pumps KTZ THREE PHASE DEWATERING PUMPS Designed to withstand the most demanding conditions found in the construction, aggregate and mining markets. Tsurumi KTZ Series dewatering pump easily converts between high head and high volume performance with a simple change of impeller and wear plate. Wide range of sizes for any job. KTZ Series Features 1 2 3 Circle Thermal Motor Protector: Protects against, overheating over amperage & run-dry.
Electric Submersible Pumps Specifications PUMP FLUID LB-480(A) • LB-800(A) • LB-1500 LB480-62 LB480A-62 LB-800 Dewatering Automatic Operation Slimline Pump Max. Capacity (GPM) 62.4 62.4 Max. Head (ft) 39.5 39.
Electric Submersible Pumps Specifications PUMP FLUID HS2.4S • HS3.75S • HSZ2.4S • HSZ3.75S • HSD2.55S HS2.4S Sand/Solids Trash Pump HS3.75S Sand/Solids Trash Pump HSZ2.4S Automatic Trash Pump HSZ3.75S Automatic Trash Pump HSD2.55S Extreme Durable Sand Pump Max. Capacity (GPM) Max.
Electric Submersible Pumps Specifications PUMP FLUID LSR2.4S • LSC1.4S • NK2-15 • NK2-22 • NK2-22L LSR2.4S LSC1.4S Ground Level Floor Level 62.4 39.5 0.236 Semi-Vortex 45 39 0.236 Semi-Vortex Impeller Material Urethane Rubber Urethane Rubber Casing Material Ethylane Propylene Rubber Ethylane Propylene Rubber Wear Plate Material Urethane Rubber Urethane Rubber Max. Capacity (GPM) Max.
Electric Submersible Pumps Specifications PUMP FLUID LBT-800 • LBT-1500 • LH23.0W • LH33.0 LBT-800 LBT-1500 Slimline Pump Slimline Pump 82 59 1/4 Semi-Vortex 111 69 1/4 Semi-Open Impeller Material Urethane Rubber Urethane Rubber Casing Material Natural Rubber Wear Plate Material Natural Rubber Shaft Seal - Type/Material Double inside mechanical seal with Silicon Carbide on Silicon Carbide faces on lower seals, and Carbon on Ceramic faces on upper seals. Max. Capacity (GPM) Max.
Electric Submersible Pumps Specifications KTZ21.5 - KTZ611 KTZ21.5 KTZ22.2 KTZ23.7 KTZ31.5 KTZ32.2 KTZ33.7 KTZ35.5 KTZ43.7 KTZ45.5 KTZ47.5 KTZ411 KTZ67.5 KTZ611 FLUID Wear Resistant Pumps Max. Capacity (GPM) Max. Head (ft) PUMP Solid Diameter (inches) 106 75 5/16 132 100 5/16 143 115 5/16 180 47 5/16 203 67 5/16 260 125 5/16 Impeller Material Semi Open High Chrome Casing Material Cast Iron Impeller Type 25.0 377 167 5/16 549 102 13/16 645 107 13/16 25.0 32.5 25.0 25.0 32.5 37.2 32.
Parts and Accessories Automatic Float Switch Hoses and Suction Strainers TSURUMI’s TS-series piggy-back float switches allow fast and easy installation of Tsurumi submersible pumps for automated operation. Simply tighten the float mounting strap to the discharge pipe, or other suitable support, and set the float tether length for the desired pumping range. (See chart below). Next, plug the pump into the float’s piggy-back receptacle and plug into electrical outlet.
Wheel Kit & Lifting Bail Wheel Kit PGWK-200 for TPG3 Series Generator & Gas Engine Pumps Wheel Kit PGWK-11K for TPG-11000HDXE Lifting Bail PGLB-1 For All Generators, Gas Engine Pumps: Wheel Kit PGWK-200 / PGWK-11K and Lifting Bail PGLB-1 Heavy-duty and easy to install our wheel kits and lifting bails fit all of Tsurumi Generators. Sand Kit Model: K15-SK Control Panels The Sand Kit can be added to the NK Series to suspend sand and prevent sand lock.
SU P E R I O R D E S I G N & T E C H N O L O G Y Anti-Wicking Cable Entrance: Maximum protection against water incursion through the cable entry. • • • Molded Cable Boot or Cable Protection Tube - extends cable bending radius, prevents abrading, and reduces fatigue. Cable Gland - provides 360 degree compression of cable boot, protection tube or cable bush for a water tight fit.
