Instruction Manual

ManualsBrandsTuffy Security ManualsFor the car066

Page 1 of 5 - 8/18/2011 – Rev122006

INSTALLATION INSTRUCTIONS

TJ Speaker / Storage Security Console #066

Please read and fill out the enclosed warranty registration card to activate your warranty.

SHIPMENT CONTENTS

Console Front Shift Lever Console Rear Mounting Bracket

Shipping Package

(2) #10 Washers (6) 5/16” Narrow Washers (2) 10-32 Locknuts (2) 5/16 Locknuts

(4) 6-32 x 5/8” Screws (2) 10-32x1/2 Screws (3) 8 x 5/8 Phillips Screws (2) 8 x 1 ¼” Phillips Screws

(3) 1/4 x ¾” Tapping Screws (2) ¼-20 x ½” Screws (2) 5/16-18 x ½” Bolts (2) 5/16-18 X 1 ¼” Bolts

Shift Boot Plate Front Console (1) 6 Speed Shifter Neoprene seal

Tray Bracket

Tools Needed

 (1) ½” wrench or ratchet, socket, and extension

 (1) ½” wrench

 (1) 3/8” wrench or ratchet, socket, and extension

 (1) 3/8” socket bit for drill (Used to insert Tapping screws, OPTION: Hole can be predrilled and the bolt could be

fastened using a wrench, or socket and ratchet)

 (1) 5/16” Wrench

 T-25 Torx

 Phillips head screwdriver

 3/8” drill bit

 Electric drill

 Silicone sealant (not necessary but recommended)

 T-30 Torx (2005 or newer Jeep)

 10mm Wrench (2005 or newer Jeep)

Summary of content (5 pages)

PAGE 1
INSTALLATION INSTRUCTIONS TJ Speaker / Storage Security Console #066 Please read and fill out the enclosed warranty registration card to activate your warranty.
PAGE 2
Installation 1. 2. 3. Please read all instructions before starting installation. It is recommended to use silicone sealant on any mounting points to the vehicle body to prevent future rust problems. Removing one or both of the seats will make installation easier. REMOVING THE ORIGINAL FACTORY CONSOLE Vehicles already equipped with a factory speaker console 4. 5. 6. 7. 8. 9. Remove the (4) self-tapping screws from the factory console.
PAGE 3
19. Attach the new rear drink holder to the Tuffy console using (2) 10-32 x ½ screws, (2) #10 washers, and (2) 10-32 locknuts. (Continued) Follow these steps if you are installing a non-factory speaker in the Tuffy console Warning! Make sure that there is nothing under the vehicle that will be damaged by the drill bit when drilling; the emergency brake is close to the drilling location. 20. Mark the floor at the spots corresponding with holes 1 and 4 (SEE FIGURE 2) and drill out to size 3/8”.
PAGE 4
ATTENTION: FREQUENT LUBRICATION IS NECESSARY ON THE LOCKING SYSTEM The pushbutton lock contains an “O” ring seal to protect the interior from dust and water. If this mechanism is not lubricated regularly it will become difficult to operate and it may not return to its home position preventing the key from operating the lock. If this happens simply pull up on the pushbutton to manually bring it back to its home position. Lubricate the pushbutton with a light lubricant such as silicone spray.
PAGE 5
Figure 5 Figure 6 FIGURE 7 6 Speed Shifter Bracket Tray Front Console Call (970) 564-1762 for Technical Support Page 5 of 5 - 8/18/2011 – Rev122006