Safety Information

ManualsBrandsTUOSHI ManualsComputers & AccessoriesUnlocked 4G LTE Router with SIM Card Slot -Wireless WiFi CPE, Mobile Hotspot, Wireless WiFi Router, Support T-Mobile and ATT (4 Antenna)

Report No.: AGC04298180501ES01

Page 39 of 51

EN 60950-1

Clause

Requirement – Test

Result – Remark

Verdict

ZB ANNEX (normative) SPECIAL NATIONAL CONDITIONS (EN)

1.7.5

(A2:2013)

In Denmark, socket-outlets for providing power to other

equipment shall be in accordance with the DS 60884-2-

D1:2011.

For class I equipment the following Standard Sheets are

applicable: DK 1-3a, DK 1-1c, DK 1-1d, DK 1-5a or DK 1-7a,

with the exception for STATIONARY EQUIPMENT where the

socket-outlets shall be in accordance with Standard Sheet DK

1-1b, DK 1-1c, DK 1-1d or DK 1-5a.

Socket outlets intended for providing power to Class II

apparatus with a rated current of 2,5 A shall be in accordance

with DS 60884-2-D1 standard sheet DKA 1-4a. Other current

rating socket outlets shall be in compliance with by DS 60884-

2-D1 Standard Sheet DKA 1-3a or DKA 1-3b.

Justification the Heavy Current Regulations, 6c

2.2.4

In Norway, for requirements see 1.7.2.1, 6.1.2.1 and 6.1.2.2

of this annex.

2.3.2

In Finland, Norway and Sweden there are additional

requirements for the insulation. See 6.1.2.1 and 6.1.2.2 of this

annex.

2.3.4

In Norway, for requirements see 1.7.2.1, 6.1.2.1 and 6.1.2.2

of this annex.

2.6.3.3

In the United Kingdom, the current rating of the circuit shall

be taken as 13 A, not 16 A.

2.7.1

In the United Kingdom, to protect against excessive currents

and short-circuits in the PRIMARY CIRCUIT of DIRECT

PLUG-IN EQUIPMENT, tests according to 5.3 shall be

conducted, using an external protective device rated 30 A or

32 A. If these tests fail, suitable protective devices shall be

included as integral parts of the DIRECT PLUG-IN

EQUIPMENT, so that the requirements of 5.3 are met.

2.10.5.13

In Finland, Norway and Sweden, there are additional

requirements for the insulation, see 6.1.2.1 and 6.1.2.2 of this

annex.

3.2.1.1

In Switzerland, supply cords of equipment having a RATED

CURRENT not exceeding 10 A shall be provided with a plug

complying with SEV 1011 or IEC 60884-1 and one of the

following dimension sheets:

SEV 6532-2.1991 Plug Type 15 3P+N+PE 250/400 V, 10 A

SEV 6533-2.1991 Plug Type 11 L+N 250 V, 10 A

SEV 6534-2.1991 Plug Type 12 L+N+PE 250 V, 10 A

In general, EN 60309 applies for plugs for currents exceeding

10 A. However, a 16 A plug and socket-outlet system is being

introduced in Switzerland, the plugs of which are according to

the following dimension sheets, published in February 1998:

SEV 5932-2.1998: Plug Type 25 , 3L+N+PE 230/400 V, 16 A

SEV 5933-2.1998:Plug Type 21, L+N, 250 V, 16A

SEV 5934-2.1998: Plug Type 23, L+N+PE 250 V, 16 A