TEX-100 Ethernet Extender User Manual Version 2.
Table of Contents Chapter 1 Introduction ......................................................................................................................3 1.1 Features ..........................................................................................................4 1.2 Specification ....................................................................................................5 1.3 Applications .............................................................................................
Chapter 1 Introduction TEX-100 Ethernet Extender is a high-speed Ethernet Extender with one Ethernet port (RJ-45 connector) and one VDSL port (RJ-45 connector). It is a bridge mode modem, well accommodating VDSL2 (Very-high-data-rate Digital Subscriber Loop) technology to extend Ethernet service over single-pair phone line. It is compliant to ITU-T G.993.2 standard and supports VDSL2 30a profile that features 100Mbps of symmetric data rate over the existing copper wires.
1.1 Features Cost effective bridge function to connect two Ethernet LAN Support flow control on Fast Ethernet port via PAUSE frame or Back Pressure IEEE 802.
1.2 Specification 4-position DIP Switch Selectable CO or CPE mode Selectable 30a or 17a (VDSL2 Profile) Selectable Band plan (Symmetric or Asymmetric) Selectable target SNR margin (6dB or 9dB) LED: LAN: ACT/LNK,10/100Mpbs, Half/Full Duplex VDSL: Power On/Off, CO/CPE, Idle/Trained/Link Performance* (AWG24 Wire) Downstream/Upstream LAN Interface: RJ-45 connector Complying with IEEE 802.3/802.3u/802.3x 10/100 Base-T Auto-Negotiation, Auto-MDI/MDI-X.
Power supply: DC single 12 Volt over 2.0 mm DC jack; 4.2 Watt maximum. Dimension: 73.4mm x 96.2mm x 22.8mm *The above performance data is for reference only, the actual data rate may vary depending on the quality of the copper wire and environmental factors. 1.
Chapter 2 Hardware Installation This chapter shows the front panel and how to install the hardware. 2.
1. The RJ-45 is designed to connect to the Local Network with the Unshielded Twisted Pair (UTP) cable. The LEDs on top of RJ-45 connector show the status below: 2. 3. The following table describes the DIP Switches’ setting.
Pin 1: OT, RT switch OT: LAN Extender acts as Central Office (CO) side. RT: LAN Extender acts as Customer Premise Equipment (CPE) side. Pin 2: Impulse noise protection 30a: High Speed Mode. Provides communication protection for up to 250ms impulse noise with latency less than 6 ms. 17a: Long Reach Mode. Direct data transmission with latency less than 1 ms. Pin 3: Band Plan Symmetric: Support the band plan G.997 and provide the symmetric transmission on both downstream and upstream.
Pin 4: General protection 9dB: Better channel noise protection with SNR up to 9 dB 6dB: Original channel noise protection with 6 dB SNR. 4. The following table describes the LEDs’ function of the product. 2.2 Rear Panel The DC Jack on the rear panel can be connected to power supply adaptor with the DC input.
2.
Appendix I Connector Architecture Ethernet Port Connector (RJ-45) The Ethernet Port interface is an 8 position Modular Jack. The table below displays the pin out assignments. VDSL Interface Pin Assignments (RJ-45) The VDSL interface is standard eight-pin modular jack. The table below displays the pin out assignments.
Appendix II Chassis Accessory There is also the Chassis solution for application on the rack in CO side. The major feature of the Chassis is listed below: 2U, 19”, 17-Slot rack Support 17-slot in one unit Power Input: AC: 100 ~240V or DC48: 36 ~ 60V Cross flow cooling fan built-in 100M units are hot swappable Specifications Power Input: AC : 100 ~240V or DC48 : 36 ~ 60V Power Consumption: >60W Dimensions: 76 X 212 X 88 mm (D x W x H ) Weight: 7.
