CAUTION! PLEASE KEEP POWER SWITCH ON BEFORE OPERATING THIS EQUIPMENT Turbo Air Speed up the Pace of Innovation Underbar Equipment Bottle Coolers Installation and Operation Manual Please read this manual completely before attempting to install or operate this equipment! TBC-24SD TBC-36SD TBC-50SD TBC-65SD TBC-80SD TBC-95SD TBC-24SB TBC-36SB TBC-50SB TBC-65SB TBC-80SB TBC-95SB SD series: Stainless Steel Exterior SB series: Black Laminated Vinyl Exterior or Black Powder Coating Exteri Exterior r or www.
CONTENTS PAGE SPECIFICATION 2 SERIAL NUMBER 2 INSTALLATION OF THE BOTTOM SHELVES 3 INSTALLATION OF THE DIVIDERS 4 INSTALLATION OF THE OPENER KIT 5 HOW TO USE THE BOTTLE OPENER 6 INSTALLATION 7 CLEANING & CAUTION 8 BASIC OPERATION 9 BEFORE REQUESTING SERVICE 10 WARRANTY 11-13 SPECIFICATIONS Horizontal Bottle Cooler MODEL TBC-24SD/SB TBC-36SD/SB TBC-50SD/SB TBC-65SD/SB TBC-80SD/SB TBC-95SD/SB COMP H.P.
INSTALLATION OF THE BOTTOM SHELVES 1) Before adding cans or bottles to cooler, please install bottom shelves. 2) Then install dividers. (see page 4) * Note: The size and quantities of the bottom shelves can be different according to model number.
INSTALLATION OF THE DIVIDERS 1) To re-position divider, push back wards. 2) Spring in back of divider point ʻCʼ will be shorten to about 1/2 inch. 3) Front of divider will be able to remove from point ʻAʼ and ʻBʼ. 4) Position divider in the hole, point ʻCʼ where you would like it. 5) Push divider back wards. 6) Insert front of divider in the holes, point ʻAʼ and ʻBʼ, where you would like it. ʻAʼ ʻCʼ ʻBʼ * Note : The shape and quantities of the dividers can be different according to model number.
INSTALLATION OF THE OPENER KIT 1) Bottle opener kit is inside cabinet. 2) On the front outside wall of bottle cooler, there are screws. 3) Hook the opener kit onto the screws, like drawing 1. 4) Push down so head of screw will insert into smaller opening, like drawing 2. 5) To detach it, follow above list in the reverse order.
HOW TO USE THE BOTTLE OPENER 1. In direction of arrow. 2. Grip the bottle tightly so it will not fall on removing cap. 3. The cap will drop to bottom of opener case. 4. When opener case is full, separate from cabinet. 5. Turn opener case over to empty.
INSTALLATION 1. GOOD AIR CIRCULATION - Do not place any object that will restrict air flow in front or back grills. - Turbo air highly recommends that there is ample space in rear of unit. 3 inches or more is best. 2. PLACE ON STRONG GROUND - Be sure the location chosen has a floor strong enough to support the total weight of the cabinet and contents. 3. DO NOT PLACE NEAR HEAT - Be sure to avoid hot corners and locations near stoves. - High ambient temperature will make cooling efficiency lower. 4.
CLEANING Before cleaning, turn unit off at power switch. 1. CLEANING THE INTERIOR AND EXTERIOR - The interior and exterior of the unit can be cleaned using warm water with soap. - Do not use an abrasive cleaner because it will scratch the surface. 2. CLEANING THE CONDENSER FINS - To maintain proper refrigeration performance, the Condenser coil must be free of dust, dirt, and grease. This will require periodic cleaning. Condenser fins should be cleaned at least every three months (90 days) or as needed.
BASIC OPERATION TBC-24SD, TBC-24SB TBC-36SD, TBC-36SB TBC-50SD, TBC-50SB TBC-65SD, TBC-65SB TBC-80SD, TBC-80SB TBC-95SD, TBC-95SB 1. The controller(thermostat) is located at the right inside of the unit. 2. The factory setting for the control is ʻ5ʼ, and maintains about 38˚F (3˚C) inside. 3. Set toward “1” for warmer temperature and “7” for colder temperature. Temperature Controller (Thermostat) 4. The thermostat controls compressorʼs cycling by sensing inside temperature. 5.
BEFORE REQUESTING SERVICE SYMPTOMS CAUSES SOLUTIONS Cooler is freezing products • Thermostat set too cold. • Turn the temperature dial to a warmer setting. The unit does not refrigerate at all. • There is a power connection failure problem. • Check the power cord to make sure the unit is pluged in it correctly. The unit does not refrigerate well. • The unit is in sunlight or near a heating device. • Product was put in warm. • The unit lid is opened too frequently or left open too long. • The temp.
MANUFACTURING COMPANY TWO YEAR WARRANTY Turbo air warrants to the original purchaser of every new Turbo air refrigerated unit, the cabinet and all parts thereof, to be free from defects in material or workmanship, under normal use and service, for a period of two (2) year from the date of original installation or 27 months after shipment date from Turbo air , whichever occurs first.
What is NOT covered by this warranty Turbo airʼs sole obligation under this warranty is limited to either repair or replacement of parts, subject to the additional limitations below. This warranty neither assumes nor authorizes any person to assume obligations other than expressly covered by this warranty. 1. WARRANTY IS NOT TRANSFERABLE. This warranty is not assignable and applies only in favor of the original purchaser/user to whom delivered.
Warranty Claims... All claims for parts or labor must be made directly thorough Turbo Air. All claims should include: model number of the unit, the serial number of the cabinet, proof of purchase, date of installation, and all pertinent information supporting the alleged defect. In case of compressor replacement under warranty, either compressor or compressor tag must be returned to Turbo Air along with above listed information. Failure to comply with warranty policies will result in voiding claims.